Buy or Sell Your 40 KW Generators

Reconditioned Sharples P3400 Horizontal Decanter Centrifuge, 14" dia x 56" long bowl (356 mm x 1,420 mm), L/D 4:1, 4-1/4" pitch conveyor (108 mm) for higher solids conveyance capacity, Stellite hard-surfaced, Bowl speed: 3400 RPM., Centrifugal force: up to about 3,000 G, Typical capacity: 20 80 GPM (4.5 18 m/hr) ...more

Manufacturer: CI Hayes, Type: Front Load Vacuum Furnace, Model: VMHT, Serial Number: 15534, Load Area: 30” wide x 52” deep x 30” high!, Maximum Temp: 1450°F, Electrical: 480V / 3-phase / 60 Hz; 60 KW max. continuous input, Cooling Fan: 75 / 19 HP, 2-speed, Pump:Stokes 212-11-10, Transformer: ...more

30 KW GENERAC DIESEL GENERATOR, -Mfg. 2016, -Model Number: 1520910, -Serial Number: 3000106304, -Type Code: SD0030AG162.4D18HBLY3, -Standby Rated at 30 kw / 30 kva, -Setup 120/240 Volt, Single Phase ONLY (125 Amps), -NOT Reconnectable to Other Voltages, -4 Wire, -60 Hertz, 1800 RPM, 1.0 PF, -12 Battery Volts, -Powered ...more

Qty (2) Leeds & Northrup Pit Nitriding Furnaces, 1200 F. Electric 230/3/60 49 KW each, 28" Diameter x 36 Deep Internal Dims, Brick Lined, Top Loading Nitriding Furnaces complete with Bottom-Mounted Alloy Recirculating Fan, Swing-Away Lid with Oil Seal, Side-Mounted Air Cooled Exchanger, (2) Alloy Work Baskets for ...more

Electric Heat 140 Deg. F. Wash and Rinse Temperatures, Heated Air Blow Off, 7" WIde Belt 1x1 Inch Heavy Duty Belt, 12" Part Height, 190 Gallon Wash Tank, 60 GPM SS PUMP, 36 KW Electric Heat, 150 Gallon Rinse Tank, 40 GPM SS PUMP, 36 KW Electric Heat, Sprays From Above, can be modified, Oil Coalscer, OverFlow/ Auto ...more

WEBER KSF2-1100 Wide Belt Sander (2) Heads43" Width cap.: Combination Head, Combination HeadHead Configuration:1st Head: Combination Head 15 kW.2nd Head: Combination Head 15 kW.3rd Station: Cleaning.55 KW: -- 43" Width cap. -- Operating width: 1100 mm. -- Max. workpiece thickness: 140 mm -- Min 4 mm. -- Height ...more

Make: Elumatec, Model: DG-104/02, Year: 2005, Machine Location: Michigan, Bed Length: 4,500mm/177″, Minimum Cutting Length at 90°: 13.7795″, Minimum Cutting Length Tilted at 45°: 13.7795″, Pivoting Range Inwards: 90° – 45°, (Up To 22.5° Manual with Digital Display), Tilting ...more

WEINIG Hydromat H30N High Speed Feed Through Moulder; 9-heads.The machine may be older, but is refurbished to a very high standard, is like new! Feed speeds up to 120 m/min. Four-sided planing and profiling of large workpieces at high feed speeds, also for fresh sawn timber.Heavy Duty cast-iron construction - reduces ...more

STAHLE - Saturn: Top & Bottom Sander with Return Conveyor SystemHead Configuration ● (2) Top Combination Head Sanding Units powered by: 4 kW (5-1/2 HP) Motors. ● Brush head powered by: 37 kW (1/2 HP) Motor. ● (2) Bottom Combination Head Sanding Units powered by: 4 kW (5-1/2 HP) Motors. ● Brush ...more

All wetted surfaces, including pumps and plumbing, are constructed from stainless steel—the most premium and durable option available for a parts washer. This ensures maximum longevity, corrosion resistance, and reliability. No expense was spared in the design and build of this unit, Flow:, 3' Load, 5' ...more

GE SF6 Gas Insulated Dead Tank Circuit Breaker DT1-72.5FK-F1 72.5KV 3000A 60Hz Number of Cycles: 132 Overvoltage Factor: 2.0 Voltage Factor: 1.5 Line Charging: 100A Isolated Bank: 630A Back to Back: 360A Inrush Peak: 25kA Inrush Frequency: 3360Hz Out of Phase Switching: 10kA Rated Interrupting Time: 3.0 Cycles ...more

Round Tube Diameter: 1" - 5", Max Square Tube: 4", Max Rectangle: 2" x 6", Wall Thickness:.049" -.180", Line Speed: 250 FPM, Maximum D/T Ratio: 50:1 Approx, Minimum D/T Ratio: 14:1. Approx, Line Direction: Left to Right, Complete Line with:, 3 Arm Loopco Turnstile, Entry L-Type Coil Car, Mandrel Uncoiler, Loopco ...more

Extra Heavy Duty 5-Axis Machine ideal for high speed and precision routing/sizing/milling/triming/boring of carbon fiber, fiberglass, composites, & wood, component parts, as well as machining light alloys. -- Axis strokes & quick positioning speeds: X-axis is 157" (4.000 mm) at 196 FPM (60 MPM), Y-axis is 157" ...more

, Manufacturer: Miller, Model Number: Spectrum 750, Serial Number: KB077305, Stock Number: 13853, s:, Type of output — Direct current, Straight Polarity (Electrode negative), Rated output — 70 amperes, 120 Volts DC @ 60% duty cycle, Type of input power — 3-phase; 230, 460 or 575 Volts AC; 60 Hz ...more

American Film & Machinery Model WSN-GEN-2M stainless steel, steam shrink tunnel and conveyor with self contained steam generator and number of containers per minute – depending on materials and application. Can handle middle or full body and cap shrink applications with materials of PVC, PETG, OPS and PLA ...more

used hosokawa alpine turboplex atp 315/3 ultrafine air classifier system ceramic lined, 6150 micron, 3-wheel high efficiency design. ceramic lined classifying wheels and vessel for abrasive applications, rated for fineness of 6-150 micron, feed rate of 1500-7500 kg per hour, featuring (3) 315mm diameter classifying ...more

used- gloe corporation mobile extraction system. recovery rates of 2 gpm at only 160f and 25"hg (more heat + more vacuum = faster recovery) ability to recirculate to further concentrate crude. can batch 100lbs of ground material or about 60lbs flower at a time. easy production of oil; easy scalability; no building ...more

50 KW GENERAC / FORD NATURAL GAS OR PROPANE GENERATOR, -Mfg. 2014, -Model Number: 17421970100, -Serial Number: 9073793, -Type Code: SG0050AG035.4V18HPLYA, -Standby Rated at 50 kw / 50 kva, -Setup 120/240 Volt, Single Phase ONLY (208.3 Amps), -NOT Reconnectable to Other Voltages, -4 Wire, -60 Hertz, 1800 RPM, 1.0 PF ...more

RIBEX ''ROBO'' VACUUM MEMBRANE PRESS WITH TWIN TABLE. - Usable table area of 2,730 x 1,250 x 90 mm thickness (107.5"; x 49.2"; x 3.5"; thick)- Standard overall table size is 2870 x 1400 x 90 mm (`113 x 55";). Standard vinyl rolls customer is using are 57" wide.- double worktable (automatic ...more

*****ETA April 21, 2026***** New Cummins 100 kW standby (90 kW prime) diesel generator set, model C100D6C. Cummins QSB5-G13 NR3 engine rated 173 HP at 1800 RPM, EPA Tier 3 emissions. 3/60/120/208V, 12 lead reconnectable to 480V and other voltages. 125-400 Amp main-line circuit breaker. PMG permanent magnet generator. ...more

HEESEMANN MFA 10 Wide Belt Sander, for veneer, lacquer, and solid wood sanding;1,600 mm (63") max. working width, 150 mm (5-15/16") working height.Head configuration: (1) Steel Contact Roller, (1) longitudinal segmented polishing platen head, (1) DB-S planetary unit, and (1) Brush roller.Polishing platen head is ...more

Make: Komatsu, Model: TFP612-3, Year: 2024, Machine Location: Upon Request, Max Workpiece Dimensions:72″x144″, Max Material Thickness:0.59″, X Axis Travel:156.3″, Y Axis Travel:79.5″, Z Axis Travel:9.45″, X Axis Rapid Traverse: Max 590.55 in/min, Y Axis Rapid Traverse: Max 1574.8 ...more

Used 2019 DOOSAN PUMA 4100B CNC Turning Center. With a 31.2" swing over bed, 43" between centers, and 21.7" turning diameter, it's Doosan EZ Guide, tool presetter, manual steady rest and chip conveyor for efficient machining., 2019 DOOSAN PUMA 4100B, Swing Over Bed. 31.1", Machining Length. 38.5", Distance Between ...more

TRIULZI SY.PLE.3300.6.1+3.4 Horizontal Glass Washing And Drying System - 3300 mm (130")Automated Closed-Loop Horizontal Flat Glass Washing & Drying System. The system is designed for the most effective washing and drying of glass sheets with an emphasis on quality, efficient energy usage, and minimal maintenance ...more

SKU: 137945, Condition: Used, Additional :, Was used for: Sodium Hydroxide solution, Mixing Tank, Volume: 7000 L, Max. Operating Height of Liquid: 1850 mm, Motor Rating: 4 kW, Max. Flowrate: 200 L/min, Max. Pressure: 392 kPA, Connection Sizes: 50/40 mm, Storage Tank, Volume: 12000 L, Max. Operating Height of Liquid: ...more

Complete Gold and Silver CIL process and recovery concentrator plant, includes feed and crushing circuit, ANI FLSmidth SAG and Ball Mill circuit, precious metal recovery via carbon in leach process and electrowinning. The final product from the plant was dor which was shipped off-site to a refinery. Offered with ...more

Manufacturer: Seco-Warwick, Type: Mesh Belt Brazing Furnace, Model Number: MBC-18812, Serial Number: 158966, Max-Temp: 2100°F, Furnace Dim's (approx.):, (1) Load Table: 4’ long, (2) Preheat Section: 4’ long, (3) Heating Section: 10’ long, (4) Slow Cool Section: 2’ long, (5) Water ...more

used & refurbished alfa laval decanter centrifuge model nx14 series 400. brand new control panel included technical information: throughput capacity up to 6 m3/hr effective capacity depends on the characteristics of the product and the quality of clarification required around: 2.500 lt/hr avocado oil 2.500 lt/hr ...more

*****ETA April 21, 2026***** New Cummins 150 kW standby (135 kW prime) diesel generator set, model C150D6D. Cummins QSB7-G5 engine rated 324 HP at 1800 RPM, EPA Tier 3 emissions, SN-S99098939. 3/60/120/208V, 12 lead reconnectable to 480V and other voltages. 200-600 Amp main-line circuit breaker. PMG permanent magnet ...more

LEADERMAC SMARTMAC 523. Feed Through Moulder, 5-head;Cast-iron 1-piece machine frame, specially heat-treated, for maximum stability & rigidity.: -- Head configuration: 5-Head (B-R-L-T-B), working capacity 230 x 125 mm (9-1/16" x 4-15/16"). -- Spindle sequence: 1. Bottom 7.5 kW (10 HP), 2. right 5.5 kW (7.5 HP), 3. ...more

BÜTFERING SCO 313 QCH Diamond. 3-Head Wide Belt Sander, 1,350 mm (53") working width. Constant pass-line.Perfectly suitable for veneer & solid wood sanding, lacquer sanding, as well as High Gloss.Head configuration: (1) Cross belt sanding head, (1) Combination head consisting of Contact Roller & Finishing ...more

Friulmac Model Dualfeed 2.5 Automatic Double Crosscut saw & Moulder Feeder Working Units on each side Trimming Unit: Motor Power: 4kW (5.36HP) Spindle RPM: 3750RPM Spindle Diameter: 30mm Max Blade Diameter: 250mm Adjustments: In/Out: Manual Up/Down: Manual Dust Extraction: 1+1 Dust Ports with 100mm outside ...more

Material- Carbon Steel, Material Thickness max/min - 6.5mm/0.20mm, Entry Uncoiler, Snubber Roll, Straightener, Coil Weight - 7 ton, Coil outside diameter, max - 1400 mm, Coil inside diameter - 508 mm, Max material width - 630 mm, Material Thickness max/min- 6.0 mm/ 0.40 mm, Roll Face- 680mm, Max Speed- 300 m/min ...more

LEADERMAC LMC-723 Feed Through Moulder, 7-head;1-piece, Cast Iron Machine Frame is specially heat treated for maximum stability and rigidity.: -- Head configuration: 7-Head (B-R-L-R-T-B-U), working capacity 230 x 150 mm (9-1/16" x 5-15/16"). -- Spindle sequence: 1. Bottom 7.5 kW (10 HP), 2. right 7.5 kW (10 HP), 3. ...more

Price on request:, m.lamprecht@eurolux.de +49 176-93263486 We can also deliver the BAV vacuum process system to you. Just ask us., More BAV vacuum process system on our website:, https://eurolux.de/, We look forward to your inquiry., Cat. no. 09-2600, Year of construction: 2007, Batch size: 60-160 liters, Mixing ...more

The DCA20SPXU4F is a 20 kW Single Phase generator with 1.0 power factor and 12/240 volt output, Unit, Prime Rating 20 kW, Standby Rating 22 kW, Generator RPM 1800, Voltage - Single Phase 120/240 V, Generator Design Revolving field, Self-ventilated, Drip-proof, Single bearing, Voltage Regulation (No Load to Full Load) ...more

COMEVA - G-300,.4-Axes CNC Controlled Door Frame/Jamb Milling Machine: Designed for cutting and milling the stiles and rails (headers) of door frames/jambs using a saw blade which rotates from +/- 45 & 90 straight cuts (rabbet-step cuts) and a router head for the milling pockets of all types of hinges and locks. ...more

LEADERMAC SMARTMAC 523. Feed Through Moulder, 5-head;Cast-iron 1-piece machine frame, specially heat-treated, for maximum stability & rigidity.: -- Head configuration: 5-Head (B-R-L-T-U), working capacity 230 x 150 mm (9-1/16" x 5-15/16"). -- Spindle sequence: 1. Bottom 11 kW (15 HP), 2. right 7.5 kW (10 HP), 3. ...more

1994 Stulz Air Technology Systems Incorporated DESICAIR-Series Desiccant Dehumidifier. Model: DES-4250-106-E. S/N: 9403214. Conditioned air quality: 4250 cfm. Process face velocity: 616 ft/min. Process ESP: 0.5 in. WC. Rotor nominal speed: 23 rpm. Inlet temperature: 96 °F. Outlet temperature: 142 °F. ...more

Special s:, -Motorized crowning, -Motorized folding beam adjustment, -Motorized BMP adjustment, -Hydraulic tool clamping, -MAH 25 motorized backgauge, - L-shaped table extensions, - Working range 10 mm - 1600 mm (.393" – 63")/10 mm - 3200 mm (.393" – 126"), - Steel ball rollers for easy ...more

1.3 KIP ITS-600 Vibration Test System with Power Amplifier, (1) New Frank Bacon Model ITS-600, 1,320 lbf (5.87 kN) Electrodynamic Vibration Test System with Power Amplifier., ITS-600 Vibration System, Sine Force Rating: 5.87 kN (1,320 lbf), Random Force Rating: 4.10 kN (921 lbf), Shock Peak Force Rating : 11.76 kN ...more

used- cummins 600 kw standby (545 kw prime) diesel generator, model dqca, sn-c090235145. cummins qsk23-g7 nr2 engine rated 1220 hp at 1800 rpm, sn-00319501, epa tier 2 emissions. 3/60/277/480v, 12 lead reconnectable to other voltages. 1200 amp main-line circuit breaker. pmg permanent magnet generator. oversized ...more

Spec Sheet:, The 2007 Clausing CSG-618ASD II is a precision 6" x 18" hydraulic surface grinder designed for high-accuracy grinding tasks. Based on technical data for the Clausing/Equiptop 618 series, the are as follows:, Capacity and Table, Table Size: 6" x 18" (152 x 460mm), Longitudinal Table Travel (Hydraulic): ...more

Used 1,200 Liter A Berents Becomix homogenizing planetary mixing system, model RW 1200 CD + MV1000, stainless steel construction, 1,628 liter total capacity, 1,200 liter working capacity, bottom mounted 23 kW homogenizer head, top mounted 12.65 kW anchor agitator with bottom and sidewall scrappers, vessel rated -1/+2 ...more

EMMEGI PRECISION C2 TU/5 Twin Head Double Miter Saw for Window Profile Fabrication - 6 Meter (20 ft.)Twin head, cutting off machine with: (3) Controlled axes with automatic movement of the mobile head, and electronic management of all 45 (internal) to 15 (external) angles. Blades feed driven by: Hydropneumatic ...more

EMMEGI - PRECISION TS2 TU/6: Twin Head Double Miter Saw for Window Profile Fabrication - 6 Meter (20 ft.)Twin head, cutting off machine with: (3) Controlled axes with automatic movement of the mobile head, and electronic management of all 45 (internal) to 15 (external) angles. Blades feed driven by: Hydropneumatic ...more

MACHINE #13670487. TYPE #HW05-590-2. OVERALL CLEARANCE L TO R IS APPROX 80.5". APPROX DISTANCE BETWEEN "FRAMES" IS 28". TWO OIL HEATED PLATENS THAT ARE APPROX 4.75" THICK. LOWER PLATEN HAS OPTIONAL CONTINUOUS GEAR/CHAIN DRIVEN FOIL/MYLAR BELT (4.5" DIA ROLLERS). DAYLIGHT BETWEEN THE HEATED PLATENS IS APPROX 50". EIGHT ...more

used- avian pasg2000 shredder and g80/120 granulator system. shredder : 2000 mm rotor diameter; 6000x1600x1600mm feed hopper; (480) 30mm blades; (1) shaft; (2) 90kw 415v/50hz/3p motors; plc controls; 15kw 415v/50hz/3p hydraulic motor; conveyor. granulator : 800 x 1200mm working width; 800mm rotor diameter; 7 set ...more

VIET VALERIA S 3 333 TM + 3CCC Inf. 1350. Top & Bottom Wide Belt Sanding LineMonolithic welded steel frame. The thickness of the steel guarantees the solidity and stability of the entire structure and reduces vibrations. 1,350 mm (53") working width, working height max.160 mm, min. 3 mm (6-5/16" - 1/8"), min. ...more