Buy or Sell Your 10 Foot Power Squaring Mechanical Shears

SERIAL. 4966, MODEL. SH5216A, YEAR NEW. 2011, CAPACITY. 16 GAUGE, CAPACITY STAINLESS. 20 GAUGE, LENGTH OF BLADES. 52", STROKE PER MINUTE. 20, FRONT ARM SUPPORTS. 2, BACK GAUGE. 26", PASS LINE. 32", BLADE ANGLE. 1 DEGREE, PNEUMATIC FOOT PEDAL. YES, PSI. 190 TO 115, FOOT PEDAL. YES.

Pre Owned Lodge & Shipley Model 2CT40i High Speed Power Squaring Shear New 1978, Serial Number 50046, Capacity (Mild Steel) 12 Gauge, Distance Between Housings 42 3/4”, Back Gauge Range 0 - 24”, Throat 10.5”, Strokes Per Minute 120, Hold Downs: 5, Distance Under Hold Downs 3/8”, Main Drive ...more

Plate thickness (max.) 0.39 in Working Length 126 in Rear stop 30 IN Cutting angle 1.5 deg Hold-down 15 positions Work Table Height 32 in Support arms 49.61 in Number of support arms 3 positions Motor rating hydraulic pump 20.1 Hp Overall dimensions (length x width x height) 161x78x64 in WEIGHT 22,660 lbs s Foot Pedal ...more

Accurshear 6’ x 10 Gauge Low Profile Hydraulic Shear, Model 61356, Serial # 1264, Asset # 15842, Capacity 10 Gauge, Cut Length 6’, Knife Size 1 x 3, Knife Length 76”, Number of Holddowns 10, Holddown Tonnage 10 Tons, Full Stroke 34 Cycles per Minute, Short Stroke 60 Cycles per Minute, Motor 10 HP ...more

19 Stands 20.00" x 1.50" Michigan Rollform Rollforming Line, Model Number: 15GMHU-20-L, Rollformer was Rebuilt by MRF in 2023., Line was only run for 2 months after rebuild., Consisting of the following:, -Uncoiler: New in 2023, 6,000# x 16" Wide Capacity, Non-Powered Pulloff Style Payoff Reel, Manual Mandrel ...more

Shears, Hydraulic48"1/4" Mild Steel, 10 Ga. Stainless Steel, 3/8" Soft Aluminum20 Ga.12-202 degrees34.5""24"24" Manual Backgauge7.5 HP, 3 Phase, 220V/35A (440V/18A Optional)1 HP 220/440V, 3 Phase17 Gallons74" x 86" x 63"5,350 lbs..

PUNCHING, PUNCH PRESSURE 66 tons, PUNCH WORK TABLE Includes back gauge and adjustable stops., ADJUSTABLE SEE-THROUGH PUNCH STRIPPER For fast and easy setup. With electronic safety interlock., DIE HOLDER Adjustable for quick punch and die alignment., STANDARD TOOLING 1-1/4" x 5/8", OVERSIZE TOOLING 1-1/2" x ...more

EquipmentIronworkersSunrise IW-110S Hydraulic IronworkerSunrise IW-110S Hydraulic IronworkerHave one to sell?Sell Now1 (714) 253-4707used@jpsint.comConditionNewQuantity1 availableRequest QuoteLoading.NewHave one to sell?Sell NowOverviewType:IronworkersManufacturer:SUNRISEModel:IW-110SStatus:For SaleThis model is in ...more

One-man Operation Hydraulic Tire Shear with removable tongue and two hand controls for safe operation., • 18 HP gas motor with electric start, • 3400 RPM • Salami double pump, • Shear Capacity: light truck - passenger tires Off Road -Semi - Farm Tractor - Road Grader Tires, • Shear Cycle Time: ...more

WYSONG 1252 POWER SHEAR 12 GA. X 4' #7139 #2, Capacity: 12 Ga. (Mild Steel), Cutting Length: 52, Rake Angle: 5/16 / Ft, Number of Hold Downs: 8, Back Gage Range: 24, Floor to Bed: 33, Speed: 60 SPM, Motor: 5 HP 220 / 440 V, Dimensions: 95 X 64 X 64 High, Weight: 4,500 Lbs, Front Operated Manual Back Gauge ...more

55 Ton Ironworker with Flat Bar Shearing, Punching Station, Angle Shearing and Open Station for Additional Tooling., Tonnage: 55 T, Angle: 4” X 4” X.25”, Power: 5 HP, Throat: 7.5”, Stroke: 6.75”, Punch Capacity: 1-1/16” Ø in ” Mild Steel, Flat Shear Capacity: ...more

JLT 720A-8W Face Frame Assembly Table. The JLT CLAMPS Face Frame Assembly System simplifies the assembling process. -- This is to ensure flush alignment of frames regardless of thickness of material. -- Major face sanding is eliminated. -- Total 1"; thick, 5' x 8' clamping surface featuring a high quality UHMW ...more

GMC 10′ x 1/4″ Heavy Duty Hydraulic Shear, HS-1025E, Inventory # 7766, Model: HS-1025E, Cutting Capacity:, Mild Steel: 10′ x 1/4″, Stainless Steel: 10′ x 10 Gauge, Blade Length: 120″, Strokes per Minute: 10 – 15 (Adjustable), Work Table Height: 34 1/2″, Front Support ...more

UNIQUE 280-3-60 Door ClampThis 3' x 6' Door Clamp Table on a 60 angle, is designed for ALL shops to accurately square and clamp cabinet or entry doors, panels, etc. -- The UNIQUE magnet and pin combination mounted air cylinders, allows the operator to move them to any location on the table. -- Includes; (4) ...more

GMC 4′ x 1/4″ Hydraulic Shear, HS-0425E, Inventory # 5345, Model: HS-0425E, Capacity:, Mild Steel: 4′ x 1/4″, Stainless Steel: 4′ x 10 Gauge, Blade Length: 52″, Strokes per Minute: 12 – 20, Throat Depth: 18″, Worktable Height: 34 1/2″, Front Support Arm: 24″ ...more

Make: Accurl, Model: MasterCut.315"X10', Year: 2025, Machine Location: Upon Request, DELEM 360 touch control, AUTO Blade gap & AUTO Rake Angle adjustment, Servo driven 40″ back gauge, 4-Sided blades, Bosch Hydraulics, Siemens Motor/Schneider electrical., The Master-Cut is a 360T CNC Control which levers ...more

CAPACITY IN MILD STEEL:, AT NOMINAL RAKE OF 3/8 in ------------------ 1/2 in x 16 ft, AT INCREASED RAKE OF 1/2 in ---------------- 5/8 in x 16 ft, LENGTH BETWEEN HOUSINGS -------------------- 16 ft-3 in, DEPTH OF THROAT ---------------------------- 18 in, BACK GAUGE RANGE --------------------------- 48 in, SPEED, FULL ...more

Make: Adira, Model: GHS-0630, Year: 1999, Machine Location: Tennessee, Maximum Cutting Thickness: 1/4″, Maximum Cutting Length: 120″, Back Gauge Depth: 29″, Number Of Hydraulic Holddowns: 16, Blade size: 0.25″ x 2.5″ x 122″, Throat Depth: 12″, Table Height: 34″, Rake ...more

65 Ton Hydraulic Ironworker with Complete Punching Attachment with split dovetail mounting 5 Punch and Die sets Automatic Urethane Hold Down on the Punch Stripper and on Angle Plate and Bar Shear., Tonnage: 65 Tons, Punching Capacity 1-1/16” diameter through 3/4” plate, Throat Depth 8”, Bending ...more

Cutting capacity:, Mild steel 10 x 10 Ga., Stainless steel 10 x 14 Ga., soft alumnium 10'x 1/4", min. thickness 24 Ga, Blade length 10' 1" = 121", Strokes per minute 10-15, Worktable height 34 1/2", Front support arm 24", Back gauge 24" Manual B.G., Blade rake angle 2 degree, Oil tank cap. 26 Gal, Main Motor 7 ...more

90 Ton Hydraulic Ironworker with Complete Punching Attachment with split dovetail mounting 5 Punch and Die sets Automatic Urethane Hold Down on the Punch Stripper and on Angle Plate and Bar Shear., Punching (90 Tons): 1-1/8” Diameter Through 1” Plate, Throat Depth: 10”, Bending (Optional): 12” ...more

Geka 55 Ton Hydraulic Ironworker, Hydracrop 55 A, Inventory # 10104, Model: Hydracrop 55 A, S/N: 23278 “2011”, Punching Power: 55 Tons, Max. Punching Capacity: Ø 1 1/2″ x 3/8″, Angle Shearing Capacity: 4 1/2″ x 4 1/2″ x 3/8″, Flats Shearing Capacity: 12″ x ...more

Cutting capacity:, Mild Steel: 4'x 10 Ga., Stainless Steel: 4' x 14 Ga., soft aluminum: 1/4", min. thickness 20GA, Blade Length: 4'4", Strokes per Minute: 12-20, Worktable Height: 34 1/2", Front Support Arm: 24", Back Gauge (German SIKO):24" Powered B.G., Blade Rake Angle: 2 degrees, Oil Tank Capacity: 17 ...more

Make: Accurl, Model: MS8-8x3200, Year: 2022, Machine Location: Upon Request, Capacity: 0.24″ Carbon / 0.16″ Stainless, Cutting Length: 10.50′, Rake Angle: 0.5°-2.5°, Throat Depth: 5.12″, Working Table Height: 33.86″, Blades Length: 129.92″, Strokes Per Minute: 12-25/min ...more

Angle 4×450 tonsPunching,Shearing: flat and round bar, angle iron, T-bar.NotchingYou will NOT regret buying this carefully manufactured piece of German engineering!, Angle 4×450 tonsPunching,Shearing: flat and round bar, angle iron, T-bar.NotchingPrice, load $,3,500 USD., You will NOT regret buying this ...more

PUNCH STATION 45 TON (1-1/8 in IN 1/2 in ) THROAT DEPTH 4.25 inches MAX DIAMETER 1 inches ANGLE SHEAR 3 in X 3 in X 5/16 in ROD SHEAR.75 inches BAR SHEAR 6 in (3/8 in X 6 in ) ELECTRICS 110V, S:, - MACHINE STAND WITH PUNCH & DIE & TOOLING STORAGE RACK, - KEYED PUNCH RAM FOR SAFTEY, - 2 in DIE HOLDER, PUNCH NUT ...more

Manufacturer: Butech, Year: 2000, Model: MS-625-78, Material to Cut: HR, HRP&O, Steel, Thickness:.625" Max.,.060" Min., Strip Width: 76" Max, 24" Min., Shear Strength: 80,000 PSI Max. Up To.500" ; 50,000 PSI Max. Over.500", Line Direction: Right to Left, Shear Style: Mechanical Downcut (Single Rake), Drive: 100 ...more

Cutting capacity:, Mild Steel: 4' x 1/4, Stainless Steel: 4' x 10 Ga., soft aluminum: 4' x 3/8", min. thickness: 20Ga, Blade Length: 4'4", Strokes Per Minute: 12-20, Worktable Height: 34 1/2", Front Support Arm: 24", Backgauge: 24" manual back gauge, Blade Rake Angle: 2 degree, Oil Tank Capacity: 17 ...more

Cutting capacity:, Mild Steel: 4' x 1/4, Stainless Steel: 4' x 10 Ga., soft aluminum: 4' x 3/8", min. thickness: 20Ga, Blade Length: 4'4", Strokes Per Minute: 12-20, Worktable Height: 34 1/2", Front Support Arm: 24", Backgauge: 24" SIKO Powered Backgauge, Blade Rake Angle: 2 degree, Oil Tank Capacity: ...more

360 Rotation, New in 2012, Weight of Shear 7,100, Minimum Excavator Weight 45,000, Jaw Opening 22", Jaw Depth 25", Cutting Force 600 Ton, Repacked Cylinder, New Turn Motor.

Marvel 66 Ton Heavy Duty Ironworker, Model MSIW66S, Asset # 17726, Serial #MSIW66SM-203, Capacities & Rated on 65,000 PSI Tensile, PUNCHING, Punch Pressure: 66 tons., Punch Holder and Jog Mode., Punch Work Table: Includes back gauge and adjustable stops., Adjustable See-Through Punch Stripper: For fast and easy ...more

1000 TON AMD MDL #1000-3030 BAR SHEAR W/ ENTRY TABLE, MANUFACTURER - ADVANCED MACHINE DESIGN COMPANY, MODEL - 1000-3030, MACHINE NUMBER - 7412, TONNAGE - 1000, ROUND CAPACITY - 7 1/8" (1020 STEEL), SQUARE CAPACITY - 6 1/4" (1020 STEEL), ROUND CAPACITY - 5 5/8" (8620 STEEL), SQUARE CAPACITY - 5" (8620 STEEL), ROUND ...more

Overview, Type:IronworkersManufacturer:SCOTCHMANModel:5075Stock #:1870Status:For Sale, FOB Rock Springs, WY, ImperialMetricTonnage 50 T 45.359 t Angle (L1) 4" 101.6 mm Angle (L2) 4" 101.6 mm Angle (T) 1" 25.4 mm Power 5 hp 5 hp Throat 7.5" 190.5 mm Punch Station 50 Ton, 24" Bar Shear ...more

DISCLAIMER, Please note this machine is incompatible with the use of a rotary phase converter. Any attempt to purchase, install, or employ one, whether carried out by you or a professional service company, will automatically void the warranty. It is crucial to understand that any such actions are entirely the ...more

, Manufacturer: Cincinnati, Model Number: 2512G, Serial Number: 56811, Year: 2019, Stock Number: 14042, s:, Operator control stand, Foot pedal control, 36" power back gauge, 13' squaring arm, Ball transfers in table, Finger guard, Cutting length: 12', Maximum thickness capacity: 3/8", Length of blades: 148" ...more

, Manufacturer: Herr-Voss, Year of Manufacturer: 1997, Width Capacity: 24" Min. - 75" Max, Gauge Range:.090" Min. -.250" Max, Shear Strength: 65,000 PSI Max, Please Note: it is missing the flywheel, clutch and brake, *Currently Removed and In Storage.

Punch Tonnage Capacity: 120 Tons, Punch Capacity (.78" Mild Steel): 1.57" Diameter, Punch Capacity (1.1" Mild Steel): 1.10" Diameter, Throat Depth: 24", Blade Length: 23.8", Punch Work Height (From Floor): 45.9", Punch Travel: 3.15", Shear Capacity @ 90 Degree: 6" x 6" x.5", Shear Capacity @ 45 Degree: 2.75" x 2.75" ...more

SKU: 129197, Model: 3DL12, Condition: Used, S/N: 39378, Gauge Capacity: 0.375 in, Horsepower: 30 hp, Bed Length: 3/8" x 12', Electrical :, Voltage: 460 volts, Phase: 3-phase, Dimensions: 120.00 (H) x 84.00 (W) x 168.00 (L) inches, Additional :, Full Load Rating Amperes: 59.1 Amps, Largest Motor Rating ...more

70-ton dual operatorOptions or Upgrades, comes with an angle shear.

Overview, Type:IronworkersManufacturer:ENERGY MISSIONModel:BMT EM Ironworker-50Condition:New - Build-To-OrderYear:2024Status:For Sale, Sheet metal 6x.6", Sheet metal 9.8x.4", Blade Length 12.75", Shearing with angle 4x4x.4", Working height 34", NOTCHING, Thickness.24", Width 1.8" ...more

NEW ANSI 52-3 glass Insulators. Compliant with ANSI C29.2 and CSA C411.1 Standards- ~10" diameter- ~5.75" spacing- 20,000 lb M&E strength- Ball & socket (Type B)- Used for transmission strings (typically 69kV–230kV depending on string length)Qty: 20,000Glass - Porcelain comparisons:GlassHigher dielectric ...more

Capacity 49 tons Punch Capacity 3/16 Thru 3/4 Flat Bar Shear Capacity 3/16 x 22, 3/4 x 9 Angle Shear Capacity 4 x 4 x 3/8, 3 x 3 x1/2 Round Bar Shear Capacity 1.375 inches Square Bar Shear Capacity 1.25 inches Approx. Shipping Dimensions 75 L x 48 W x 72 H Approx. Shipping Weight 3000 pounds.

Used Durco Centrifugal Pump, Model 2K2X2X10, D20 Alloy, 2" x 2" x 10" impeller, rated 150 GPM @ 18' head at 1800 RPM, mechanical seal with lubricator, on base with 20 H.P. 230/460 volt drive, XP, Serial No. 457950.

Niagara 6′ x 12 Ga. Sheet Metal Shear Model #46, 6′ x 12 ga. capacity in mild steel, Length of knives 74-1/2″, Rake angle 5/16″, Holddowns 15, 30″ bed height, 75 strokes per minute, 18″ rear operated manual back gauge, Full length foot treadle, T-slots in front of bed, Main motor 3 ...more

Shears, Hydraulic120"10 Ga. Mild Steel, 14 Ga. Stainless Steel, 1/4" Soft Aluminum121"10-152 degrees34.5""18"7.5 HP, 3 Phase, 220V/35A (440V/18A Optional)1 HP178" x 67" x 65"8,850 lbs.

PUNCHING Max 1-1/16" thru 3/4" thick material or 65 tons Platen Surface 11" x 38" Capacity 65 tons COPING/NOTCHING 3 1/2" X 5" X 3/8" BLADE PLATE SHEAR 18" X 1/2", 12" X 3/4", 8" X 1" ANGLE SHEAR 5" X 5" X 1/2", Pre-Owned PIRANHA Ironworker, The PIRANHA PII-65 is a powerful and reliable ironworker, perfect for various ...more

Product Roper Whitney Pexto No. 455 Combination Angle Iron Shear, Notcher, BenderShear Capacity- 2″ x 2″ x 1/4″, Weight- 200 lbs, Blades are in good shape. Overall a good working unit..

SCOTCHMAN HYDRAULIC IRONWORKER, MODEL: 6509, SERIAL NUMBER: 5658FF297*, *Reconditioned December 2025, Capacity: 65 Ton, Punch: 1-1/16 In 3/4", Throat Depth: 9", Flat Bar Shear: 24", 1" x 6", 3/4" x 8", 1/2" x 12", 3/16" x 24", Angle Shear, 90 Degrees: 6" x 6" x 3/8", 5" x 5" x 1/2", Angle Shear, Miter Angle 45 ...more