Buy or Sell Your C18 Engines

SERIAL. 2H339, MODEL. UH3, YEAR NEW. 2020, AREA OF TABLE. 51.18" X 11.81", LONGITUDINAL TABLE TRAVEL. 37-3/8", CROSS TRAVEL. 14-13/16", VERTICAL KNEE TRAVEL. 18-1/2", RAM TRAVEL. 15-1/2", SPINDLE SPEEDS (VARIABLE). 35 TO 1382 RPM, LONGITUDINAL & CROSS TABLE FEEDS. 1/2 TO 24-7/8" IPM, LONGITUDINAL & CROSS RAPID ...more

Used in Very good condition after refurbish by MTC, 2012 MARVEL SERIES 8 MARK III, Power Blade tension, Power tilt, head return, Throat. 18", Work Height. 34.5", Power. 5 hp, Blade Width. 1.25", Blade Length. 184", FPM. 50-450, Dimensions. 94"L x 62"W x 92"H, Weight. 3,500 lbs.

, 18 Sq.Ft. APV Plate Exchanger. 2" inlet/outlet, APV HXC, FT2. 18 ft, Tube PSIG. 100, Tube Mat. SS, Type. PLATE, Horiz/Vert. V, Shell PSIG. 100, Shell Pass. 1, Tube Pass. 1.

Simec SB3000 Wire Brush Deburring Machine, **New in 1997**, To the best of our knowledge all listed below are deemed correct., It is the buyers responsibility to confirm all and we encourage an inspection of the machine(s) and accessories prior to purchase., Model: SB3000, Bar Capacity: 1-1/2" to 4" Diameter, Max. Bar ...more

Siemens GCA121.1E Rotary Air Damper Actuator, AC/DC 24 V, 2-Position, 18 Nm - Siemens GCA121.1E Rotary Air Damper Actuator, AC/DC 24 V, 2-Position, 18 Nm, Spring Return 90/15 sWith self-centering shaft adapter for shaft dia. 8.25.6 mm, square 6.18 mm, min. shaft length 20 mmWith position indication and adjustable ...more

Johnson Controls T-3610-1002 Pneumatic Low Limit Controller, 0 to 270 Deg F - Johnson Controls T-3610-1002 Pneumatic Low Limit Controller, 0 to 270 Deg F (-18 to 132 Deg C), Proportional, Direct Acting, 18 in. (46 Cm) Rigid Stem Element with Plastic Mounting Bracket for Unit Ventilators - Johnson Controls - Johnson ...more

LL37 | Crouse-Hinds | Condulet Cast Iron Body, Type LL, 1" | New - APPLICATIONS: Act as pull outlets for conductors being installed. Provide openings for making splices and taps in conductors. Connect conduit sections. Provide taps for branch conduit runs. Make 90deg bends in conduit runs. Provide for access to ...more

used- mobile alar auto-vac model 6120 rotary vacuum drum filter system, trailer mounted mobile. 6' diameter by 12' long drum, providing approximately 226 sqft. of effective filter surface area. designed for high-capacity solid-liquid separation, the unit operates continuously under vacuum pressure to ...more

Manual Activated Turret Punch, Make: Rotex, Model No.: 18-AK62, Serial No.: 13530, DOM: 1962, and s:,.Capacities:,.8 Ton,.5/32" - 2" Hole Diameter,.16-Gauge Mild Steel,.Metal, Rubber, & Gasket Material,.Die Stations: 18,.Throat: 18" Horizontal,.Punch Deck Diameter: 12",.Mounted on Stand, Overall ...more

Belimo CMB24-SR-R is a non fail-safe actuator delivering 18 in-lb (2 Nm) torque. It operates on AC/DC 24 V with a modulating control input of 2.10 V. The actuator's running time is 75 seconds for 90 rotation. It s position feedback of 2.10 V and has an angle of rotation up to 95. The device is designed for small ...more

BELT, SEAT, 3" SUSPENSION, BUCKET-MP, 1.4 YD3, PO, CANOPY, BASE, COUPLER, PG, HYDR.D.LOCK, BHL, COUPLING, QD, THREADED CAPS, CTWT, 1015 LBS, CUTTING EDGE, TWO PIECE,WIDE, DISPLAY, STD, ENG, 74.5KW, C3.6, T4F, FAN, STD, GUARD, STABILIZER, HYD, MP, 6FCN, INSTRUCTIONS, ANSI, LANE 2 ORDER, LINES, AUX COMBO, E-STICK ...more

The Belimo FSTF24 is a fire and smoke actuator offering 18 in-lb (2 Nm) torque with a spring return mechanism. It operates on AC/DC 24 V with On/Off control. The actuator's running time for motor operation is 75 seconds, with a fail-safe return time of less than 15 seconds. It s a manual override and has an angle ...more

Inventory No. 0226-012-0001 Manufacturer Daewoo Model No. PUMA250LB Name CNC Lathe Arrival Date 02-05-2026 Dimensions L x W x H (inches) Unavailable Electrical 3/50/60/200/220 Weight (lb.) 14260 Category CNC Condition Used Available Quantity 1 Serial No. P25L0199 Make Year 1998 Item W/fanuc Series 18-t Control, Chip ...more

Used Grizzly Industrial 52" Foot Shear, Model: G5772, Serial: 17113, Year: 2017, Capacity: 26" x 16 Ga mild steel, 52" x 18 Ga mild steel, Front step gauge range: 0"-12.5", Rear step gauge range: 0"-35", Max Thickness: 0.0478", Max Thickness (gauge): 18 gauge, Length of Blade: 52".

SKU: 116150, Model: DQKB-5641334, Year: 2004, Condition: Used, S/N: A040595981, Horsepower: 2922 hp, Fuel Type: Diesel, Hours: 250, Mount: Skid Mounted, Rating: Standby, Electrical :, kVA: 2187.5 kVA, Voltage: 347/600 volts, Phase: 3-phase, Made In: UNITED STATES, Additional :, Cummins Engine: QSK60-G6, Rated kW: 1750 ...more

Used Manesty Unipress rotary table press, model MFG 765, 27 station, keyed upper punch guides, 6.5 ton main compression, 1 ton pre compression, B tooled, 16 mm max tablet diameter, 18 mm max depth of fill, single side with force feeder with feed hopper, with control cabinet, up to 196,200 tablets/hour, serial# 15578 85.

Used Manesty Unipress rotary table press, 34 station, keyed upper punch guides, 6.5 ton main compression, 1 ton pre compression, B tooled, 11 mm max tablet diameter, 18 mm max depth of fill, single side with force feeder with feed hopper, with control cabinet, up to 247,200 tablets/hour, serial# 15458 84.

, Model: A.S., # of Stand: 18, Shaft Diameter: 2.75", Nominal Roll Space: 36", Vertical: 1.75", Horizontal Center Distance Between Stand: 10.5", Wet Gear Drive, Variable Speed Drive, Remote Hand Control, Machine Type.Roll Formers Manufacturer.ASC Model.A.S. Year.1971 Condition.Used.

Unused Battery 36 Volt Battery Charger. Model: MX3-18-775. Battery type: L-A. Amp hours: 775. (18) cells. Input AC volts: 208/240/480. Input AC amps: 23/2/10. Output DC volts: 36. Output amps max: 155, 60 Hz. 3 phase. Approximate shipping weight: 300 lbs. Overall dimensions: 2 ft. 3 in. L x 2 ft. 1 in. W x 2 ft. ...more

Capacity 90 Ton x 8' Tonnage 90 Ton Maximum Bending Length 98" Open Height 21" Throat 7" Closed Height 7" Ram Speeds Type CNC/ Hydraulic Bed Width 3.5" CNC Backgauge Cincinnati 5-Axis WEIGHT 18,000 Lbs. Stroke 14" s Cincinnati Proform Control Pro Tech Light Curtain Safety System Foot Pedal Controlled 14,742 Hours ...more

Buy Rite Finishing is proud to offer Rohner Spray Booths to our lineup of quality finishing equipment! A Paint Mix Room, or Paint Kitchen as it is often called, offers a secure & controlled work area to safely store and mix paint while being protected from harmful toxins and vapors. Our paint mixing rooms and ...more

SERIAL. 2730, MODEL. H618, LONGITUDINAL. 18-1/2", CROSS. 6-3/4", VERTICAL. 12", MAGNETIC CHUCK. 6" X 18", WHEEL SIZE. 8" X 1/2", ELAVATING.0005", CROSSFEED.001", SPINDLE SPEED. 3,450 RPM., Machine Type.Grinders, Surface, Rotary Manufacturer.BOYAR SCHULTZ Model.H618 Year.N/A Condition.Excellent.

Inventory No. 0823-314-2879 Manufacturer Grundfos Model No. MTR20-5/2 A-WB-A-HQQV Name Multi Stage Pump Arrival Date 01-08-2026 Dimensions L x W x H (inches) 40 x 17 x 18 Capacity 3.7 KW Electrical 3/50/60/208/230/460 Weight (lb.) 147 Category Pumps Condition Used Available Quantity 1 Serial No. 0001 Item 2930 Rpm.

Belimo GMX24-PC delivers 360 in-lb (40 Nm) torque, operates on AC/DC 24 V, and supports 0-20 V phase cut modulating control. s include a manual override via an external push button and a maximum rotation angle of 95, adjustable with a mechanical stop. Electrical connection is facilitated through an 18 GA plenum cable ...more

, Width: 72 inches, Thickness:.187 inches, Work Roll Diameter: 2.687 inches, Manufacturer: Herr-Voss, Thickness Range:,.043" -.187" Stainless & Carbon Steel @ 60,000 PSI Yield,.040" -.210" Aluminum @ 35,000 PSI Yield, Width: 18" - 72", Work Roll Diameter: 2.687", Roll Face: 84", Work Rolls: 17 (8 over 9), 7 ...more

Used 118,745 liter (31,372 gallon) M Roth GmbH storage tank, 304 stainless steel construction, approximately 3,900mm (153.54") inner diameter x 8,500mm (334") straight side, dish top, 55 degree cone bottom, approximately 2,400mm (94.48") deep, rated 0.9 bar at 40°C internal, jacketed cone and 196" of straight side ...more

Brand/Model: Union TX-75 : Used Union TX-75 triplex production pump package with the following s: • 4" stroke • 75 HP • #3 Steel billet fluid end • 2 3/8” plungers • 6" ANSI 150# FF suction connection • 3" ANSI 600# FF discharge connection • 5.0 gear ratio • ...more

Item DC Inverter Drive Module Manufacturer Siemens Series SIMOVERT MC Type shown on nameplate Wechselrichter DC Inverter Part number 6SE7032 6TG50 Z Order options shown C43 F01 G44 G91 K01 K11 K80 Serial number T P42247600015 Input DC 510 to 650 VDC Input current 250.0 A Output 3 phase AC 0 to 327 to 413 VAC Output ...more

Arm: 7', Column: 15", Spindle taper #6 MT, Speeds: 18 to 1,124 RPM, Feed in Thousandths: 6 to 125, Threads Per Inch: 8, 11.5, 14, Motor: 7.5 HP 3 Phase, Capacity in Steel: 23/4", Rapid Traverse, Power Clamping, Right Angle Base, Freight charges are not included in sale price. Freight scheduling and costs are ...more

6/24/20, BATTERY, HEAVY DUTY, 850 CCA, CERTIFICATION ARR, (US/CANADA), CONTROL, ISO, ON/OFF, COUNTERWEIGHT,MACHINE,EXTERNAL, DISPLAY, BASIC, ANTI-THEFT, DUAL SELF LEVEL, Engine, FAN, COOLING, DEMAND, INCLUDES: STANDARD FLOW, INSTRUCTIONS, ANSI, USA, LIFTING EYES, FOUR POINT, LIGHTS, LED, Online Owner's Manual ...more

SERIAL.1048, METAL THICKNESS CAPACITY. 18 GAUGE, NUMBER OF STANDS. 7, MAXIMUM STOCK WIDTH. 3-7/8", SHAFT DIAMETER. 1-1/4", HORIZONTAL SHAFT CENTER DISTANCE. 4", FLOOR TO PASSLINE. 35", CURRENTLY SET UP 1/2" PITTSBURGH, ENTRY & EXIT ADJUSTABLE EDGE GUIDES, 1/2 HORSEPOWER MAIN MOTOR.

2024 CAT 420XE, 420 LANE 2 ZCON, BELT, SEAT, 2" SUSPENSION, BUCKET-GP, 1.5 YD3, IT, BUCKET-SOIL, 24", 8.5 FT3, COUPLER, PG, MAN.D.LOCK, BHL, COUPLING, QD, THREADED CAPS, Customer Value Agreement (CVA) 2 yar/1000 hour parts kit only, CUTTING EDGE, TWO PIECE,WIDE, ENG, 82KW, C3.6, T4F, FENDERS, FRONT, INSTRUCTIONS ...more

SERIAL. JLC-708YP, MODEL. ELC.2016-3, CAPACITY. 1 TON, LIFTING HEIGHT. 15', LIFTING SPEED. 16 FPM, HEAD ROOM. 18-1/8", PENDANT CONTROL. 2 BUTTON, CHAIN BOX. YES, VOLTAGE. 220/440, PHASE. 3, MAIN MOTOR HORSEPOWER. 1, WEIGHT. 109 LB.

Haas DM-1 CNC Vertical Machining Center, used. : 20" X, 16" Y, 15.5" Z, 15 hp, 15,000 RPM, 18 ATC, 40 Taper. s Wireless Intuitive Probing, High Speed Machining, Rigid Tapping, Chip Auger, Mist Collector. Ready for 4th Axis., 2015 HAAS DM-1, X. 20", Y. 16", Z. 15.5", Power. 15 hp, RPM. 15,000 RPM, # ATC. 18, Taper. 40 ...more

;- FOLEY WORK READY - ATTACHMENTS SHOWN SUBJECT TO CHANGE AND MAY NOT BE INCLUDED IN PRICE, AIR INTAKE, STANDARD, ANTIFREEZE, -36C (-32F), CAB, DELUXE, SINGLE BRAKE, CPLR HPL-ISO,STD FLOW, ENGINE, 55KW, C3.3B, STAGE 5, FAN, COOLING, ON DEMAND, PACKAGE, BASIC, GUARD, HORIZONTAL COUPLER, Heater, HYDRAULIC OIL ...more

Smart Infrared Temperature Sensor, 8-14 m, Plastic Fresnel Lens, -18 to 500C (0 to 932F), 18 available. $1,500 each, TX Series Smart Sensors communicate over a simple loop-powered 2-wire cable using the HART (Highway Addressable Remote Transducer) protocol. This signal combines industry-standard 4-20 mA output with ...more

Ultramatic 5 Cubic foot capacity Vibratory finishing mill With separator screen and Media inside plus two extra boxes, Variable speed, Electrics and timer, Roto -finish, ultra-matic vibratory bowl, Spiral bowl dimensions 9" wide channel, varying in depth from 18" to 9", 2 Horse power Drive, Variable speed from 900 to ...more

used- endflex boxxer t series automatic case erector, manual loader and automatic case taping system, model t-18. capable of speeds up to 18 cpm (depending on application). approximate case size range: 9.5" to 20" long x 7.5" to 16" wide x 5" to 16" diagonal. automatic case erector and bottom taper, boxx pack manual ...more

The MITSUBISHI MODEL RD23-B35P is a CNC plain cylindrical grinder designed for precision grinding of cylindrical parts. It s a Fanuc 18T control system and can handle workpieces up to 9.1" swing and 13.8" center distance. It's s like a live/dead headstock, tailstock with taper adjustment, and a single-point ...more

eBay, SHIPPING IS AN ESTIMATE Hendey 14"x54" Heavy Duty Prescision Engine Lathe w/ Chuck and Tool PostMake: The Hendey Machine Co., Model: 14x54, Serial No: 32283, Condition: Used, Overall in Great Shape, Will be Tested soon. Freshly Painted, Comes with 8" 3 Jaw Chuck and 4 Slot Tool Post Holder, 14"x54", 1.5" Through ...more

Brand: SQUARE D, Condition: USED, "AS-IS", Model: 12256406310120001, Part: -, Serial: -, Power Rating: 50 AMP, 120/240 VAC, 1 PH, 3 WIRE, BREAKERS: (18) BREAKER SLOTS, Weight: 90 LBS W/ SKID, Category: PANELBOARDS, Shipping Dimensions: 26" x 20" x 6", ERC #: MO-5442, Job #: 116, Additional Notes: TYPE 1 ENCLOSURE.

Make: Vicon, Model: 53C-G, Year: 2024, Machine Location: Upon Request, Vicon 53C-G Underfed Coil Cradle, Number of stations 3, Max. Coil weight 12,000 lbs., Max. Coil width 60″, Max Coil OD 42″, Coil ID 20″, Vicon V-IDM Hydraulic Drive Motors, One additional geared coil spool, Vicon V-PR-5 Powered ...more

1989 Muller Martini Norm perfect binder configured with 18 gathering stations and 20 clamps with three knife trimmer, forming a full perfect binding line., Manufacturer: Muller Martini, Model: Norm 3000 1/2S, Year: 1989, Machine Type: Perfect Binder, Gathering Stations: 18, Clamps: 20, Mechanical Speed: Up to approx. ...more

Lifeguard 36 Volt Battery Charger. Mfg: KW Battery Company. Model 18-1050F3B-22. Type: LA, cells: 18, ampere hour: 876-1050. (Input) AC volts: 208/240/480, AC amps: 36/32/16, 60 Hz, 3 phase. (Output) DC volts: 36, DC amps 210. Unit s independent lights for varied battery and charger status and a toggle button to ...more

Bin vent type dust collector, Griffin model 18BDP, rated at 100 sq. flat top. bag area, 18 bags, 4-1/2" diameter x 4-1/2' long. Unit rated for 1000 CFM at 10:1 air to cloth ratio, 2 HP blower mounted on top, all stainless steel contact parts, cone bottom., Square Ft.: 100, Basis: FOB.