Buy or Sell Your Vertical Lathe

This is a USED Jet GH-1440ZX Gap Bed Lathe, Stock #321910 and has a 14" swing & 40" centers. Gap width is 12" & it will swing 23-5/8" in that gap. s a huge 3-1/8" spindle hole & 12 spindle speeds from 42 to 1800 RPM's. Then longitudinal feed rates of.0015"-.0900" IPR, cross feeds from.0006"-.0360 IPR. Will ...more

Unused 50 Gallon Stainless Steel Jacketed Pressure Vessel, Manufacturer: Paul Mueller, Capacity: 50 gallons, National Board: 2218, Serial: 128051-5, Year: 1993, Internal pressure: 30 psi @ 300F, Jacket pressure: 90 psi @ 300F, Dimensions: 20" dia. x 30" straight side, Mounted on legs with wheels, 1993 PAUL MUELLER 50 ...more

SKU: 137975, Year: 2015, Condition: Used, Additional :, Original Designation: MCC-N Tertiary Crushing & Screens area, Bus Voltage: 575 V, Short Circuit Rating: 25 kA rms Sym, Board Rated: 800 A, Horizontal Busbar Rated: 800 A, Vertical Busbar Rated: 800 A, Form: 4A, Enclosure: IP42 custom built.

SERIAL. 784019611848, MODEL. 16, SWING OVER WAYS. 16", SWING OVER CROSS SLIDE. 10", DISTANCE BETWEEN CENTERS. 80", SPINDLE SPEEDS. (18) 40 TO 2000 RPM, HOLE THRU SPINDLE. 2-5/8", ENGLISH FEEDS. (38).0016 TO.028 IPR, ENGLISH THREADS. (38) 2 TO 72 TPI, METRIC THREADS. (39).2 TO 14 TPMM, TAPER. YES, CHUCK. 12" 4 JAW ...more

SERIAL. 224774, MODEL. SERIES I, YEAR NEW. 1981, AREA OF TABLE. 42" X 9", SPINDLE SPEEDS, VARIABLE. 60 TO 4200 RPM, SPINDLE FEEDS.0015,.003,.006 IPR, LONGITUDINAL TABLE TRAVEL. 30", CROSS TRAVEL. 12", VERTICAL KNEE TRAVEL. 16", QUILL TRAVEL. 5", RAM TRAVEL. 12", DEPTH OF THROAT. 6-3/4" TO 18-3/4", TAPER IN SPINDLE. ...more

Stock #: 85096 Category: Vertical Motors HP: 150 RPM: 1790.00 Frame: L444VP16 Enclosure: WPIBB Make: Electric Volts: 460 Service Factor: 1.15 Condition: Electrically O.K. Location: Toledo, OH.

Stock #: 71308 Category: Vertical Motors HP: 400 RPM: 885.00 Frame: 588U Enclosure: WPIIBB Make: Siemens Volts: 4160 Service Factor: 1.15 Condition: New Surplus Location: Toledo, OH.

Used Approximately 1,050 Gallon Stainless Steel Tank, Manufacturer: Perry Products, Capacity: 1,050 gallons, Dimensions: 65" dia. x 74" straight side, Material of construction: 304 stainless steel, Flat top, cone bottom, 1962 PERRY PRODUCTS 1,050 Gallon, Capacity. 1,050 gal, Diameter. 5.42', Height. 6.17' ...more

CEMCO MBV 54 Vertical Boring Machine54" x 15" Cast iron table with wooden top,:(2) Universal spindles with movable spindle supports,(3) 2 HP - 1,725 RPM direct drive spindle motors,36" Stationary table height; 6" Max. vertical stroke, spindles advance hydraulically at 0 - 30 strokes/Min;Foot pedal actuated w/single ...more

SERIAL. 14E-144, MODEL. MAKINO SERVO SHIFT, SWING OVER BED. 19", SWING OVER CROSS SLIDE. 12-1/4", DISTANCE BETWEEN CENTERS. 72", SPINDLE SPEEDS. 40 TO 1,600 RPM, SPINDLE HOLE. 3", CHUCK. 3 JAW, THREADS INCH. (48) 2 TO 112 TPI, THREADS METRIC. 0.25 TO 14 MM, FEEDS. (48) 0.0018" TO 0.104", CROSS SLIDE TRAVEL. 11-1/4" ...more

SERIAL. 124890520, MODEL. 1340BV, YEAR NEW. 2012, SWING OVER BED. 13", SWING OVER CROSS SLIDE. 8-1/4", DISTANCE BETWEEN CENTERS. 40", SPINDLE SPEEDS. 40 TO 200 RPM, SPINDLE HOLE. 1-9/16", CHUCK. 3 JAW, THREADS INCH. 2 TO 56 TPI, THREADS METRIC. 0.5 TO 12 MM, LONGITUDINAL FEEDS. 0.0016" TO 0.046", CROSS FEEDS L. ...more

K&S Exit Coil Car, -Capacity: 20,000# x 48" wide, -40" Wide Bed, -60" O.D. Capacity, -24" Vertical Lift, -4" Bore Hydraulic Cylinder, -Self Contained Hydraulics, 5 HP AC Motor, 1800 RPM, -Coil Retaining Arms, -Retractable Cable Reel, -Overall Size: 66" L x 55" W x 68" High, -In Storage: Toledo, OH.

Model: MA1212HD, Free-Standing X-Base, Hand Pendant Controller, 90 Day Warranty, 12 ft of Horizontal Travel (Variable Speed), 12ft of Vertical Travel, 750 lb Boom End Capacity, 460 Volt Input, 184" Under the Boom to floor max.

SERIAL. 604, SERIES. II, AREA OF TABLE. 58" X 11", SPINDLE SPEEDS. 50 TO 3500 RPM (VARIABLE), POWER LONGITUDINAL FEED. 3/4 TO 24 IPM, POWER CROSS FEED. 3/4 TO 24 IPM, LONGITUDINAL TRAVEL. 30", CROSS TRAVEL. 15", VERTICAL TRAVEL OF KNEE. 16", QUILL TRAVEL. 5", POWER QUILL TRAVEL. YES, HORIZONTAL TRAVEL OF RAM ON BASE. ...more

Working Surface 10" x 50" Logitudinal Travel 34" Cross Travel 16" Vertical Knee Travel 16" Ram Travel 20" T-Slots Number and Size 3, 5/8" Main Motor 3 HP Head Moves Right to Left 90° Head Tilts front to Back 45° Spindle Drive Variable Spindle Speed 60 ~ 4,500 Spindle Taper R-8 Power Quill Feed 0.0015", 0.003" ...more

SERIAL. 8353-T, MODEL. HLV-ME, SWING OVER WAYS. 11", SWING OVER CROSS SLIDE. 6", DISTANCE BETWEEN CENTERS. 20", SPINDLE SPEEDS. (16) 125 TO 3000 RPM VARIABLE, ENGLISH THREADS. (36) 11 TO 108 THREADS PER INCH, METRIC THREADS. (36).275 TO 2.7 PITCH IN MM, SPINDLE HOLE. 1-1/2", CHUCKS. 6" 3 JAW & 6" 6 JAW, COLLET. ...more

AIR TECHNICAL INDUSTRIES ZLH-45084-E-M Zero-Low Scissor LiftGround level, roll-on loading, roll-off unloadingThe FIRST scissor lift table to lower to ground level for easy loading of wheeled cart or pallet truck. : -- Capacity: 4000 Lbs. -- Platform Size: 50"; x 84";. -- Lowered Height: 3/4";. -- Vertical Travel: ...more

UTUBE NUMBER: 3175, MANUFACTURER: RAFTER, Number of Stands: 10, Line Direction: Right to Left, Spindle Diameter 2-1/2", Roll Space: 30", Horizontal Centers: 13" on Passes 1 – 8, 104-1/4" Space, 13" on Passes 9 – 10, Vertical Adjustment: 7-1/4" 9-3/4", Base Top to Center Lower ...more

, Cushman 10264G Lathe Chuck for sale: 10" diameter, 4 jaws, 2-3/4 center hole. Used condition, ideal for precision lathe work. Stamped number 10264G. Enhance your machining setup with this reliable tooling accessory., Spec Sheet:, Cushman 10264G Lathe Chuck 10 4 Jaw, USED, Brand: Cushman Chuck Company, Type: Lathe ...more

, CMEC 19.75 inch 4 Jaw Lathe Chuck available. This used lathe chuck s 4 jaws, a 19-3/4in overall diameter, 3in center hole, and weighs 170lbs. Ideal for tooling requirements, fitting with D1-8 back., Spec Sheet:, CMEC 19.75 inch 4 Jaw Lathe Chuck, USED, 4 Jaws, Type: Lathe Chuck, Overall Diameter: 19-3/4in, Center ...more

Spec Sheet:, Lathe Chuck Jaws 3 Piece, Used, Lathe Chuck Jaws, Set of 3, Measured Dimensions: 3.5x1.5x1 (inches), Stamped: 1-2-3, each jaw numbered.

Used Vertical machining center with Siemens Sinumerik 5-axis CNC control. Key s include 8000 RPM spindle, 17.5 HP motor, swiveling rotary table, tool changer, and chip conveyor., Table Dimensions, L x W 24.8" x 19.7", Table Load Capacity 440 LBS, Longitudinal Travel (X-Axis) 19.7", Cross Travel (Y-Axis) 17.7" ...more

SERIAL. 25C495, MODEL. 25, SWING, SPINDLE CENTER TO LOWER COLUMN. 12-1/2", SWING, SPINDLE CENTER TO UPPER COLUMN. 11-1/2", AREA OF WORK TABLE, T-SLOTTED. 30" X 16", TABLE TRAVELS. 20" X 12", VERTICAL TABLE ADJUSTMENT. 12", MAXIMUM DISTANCE SPINDLE TO TABLE. 27", VERTICAL ADJUSTMENT OF SLIDING HEAD. 18", POWER FEED ...more

, Tapping, Spindle guide w/emergency stop, Work lamp, Coolant system, Operating tools, Manual, Manufacturer Knuth Knuth Single Spindle Drill Model SSB 32 XN Condition New Serial Number 6058 Stock Number 11148 Drill capacity 1.26" Tapping capacity, mild steel M20 Column diameter 5" Throat depth 12.5" ...more

LOCKFORMER 14 STAND DUPLEX ROLLFORMER, MODEL | 14D-SC, NUMBER OF STANDS | 14, SHAFT DIAMETER | 1-3/8", HORIZONTAL CENTERS | 8", VERTICAL CENTERS | 4-1/2", MAX SHEET WIDTH | 60", ELECTRICAL | 240/480 VAC 3 PHASE, CURRENTLY WIRED 480 VAC, MOTOR: 10 HP.

Used Approximately 200 Gallon Stainless Steel Mix Tank with Purge System, Mfr: Pepper/+Fuchs, Capacity: 200 gallons, Dimensions: 36" dia. x 48" straight side, Top, off-center mounted drive with agitator, Includes side mounted Pepperl + Fuchs Model 6000 Type X purge system which is a complete automatic system that will ...more

TISHKEN FOUR STAND ROLL FORMER, MODEL NUMBER. 4-MW-2, SERIAL NUMBER. 21094293, ARBOR DIAMETER. 2", ROLL SPACE. 14", LOWER ARBOR FROM BASE TOP. 5", VERTICAL ADJUSTMENT. 3", ESTIMATED DC DRIVE. 20HP, A 3 AXIS STRAIGHTENER YES, MISSING ONE OUTBOARD SUPPORT.

SERIAL. 10E-148, MODEL. REGAL, SWING OVER WAYS. 19-1/2", SWING OVER CROSS SLIDE. 12-1/4", DISTANCE BETWEEN CENTERS. 96", SPINDLE SPEEDS. (12) 40 TO 1600 RPM, SPINDLE TYPE. L, FEEDS. (48).0018 TO.104 IPR, THREADS (INCH). 2 TO 112 TPI, THREADS (METRIC).25 TO 14 MM PITCH, DIAMETER OF SPINDLE HOLE. 1-3/4", CHUCK. 12" 3 ...more

K&S Exit Coil Car, -Capacity: 20,000#, -40" Wide Bed, -60" O.D. Capacity, -24" Vertical Lift, -4" Bore Hydraulic Cylinder, -Self Contained Hydraulics, 5 HP AC Motor, 1800 RPM, -Coil Retaining Arms, -Retractable Cable Reel, -Overall Size: 66" L x 55" W x 68" High, -In Storage: Toledo, OH.

Stock #: 82990 Category: Vertical Motors HP: 75 RPM: 1785.00 Frame: L365TP16 Enclosure: WPIBB Make: Electric Volts: 230/460 Service Factor: 1.15 Condition: Electrically O.K. Location: Toledo, OH.

Stock #: 90275 Category: Vertical Motors HP: 350 RPM: 1785.00 Frame: L509TP20 Enclosure: WPIBB Make: Electric Volts: 4000 Service Factor: 1.15 Condition: New Surplus Location: Toledo, OH.

Stock #: Lagun-AT-1840/60/80/120-G-TWBrand: Republic LagunModel: AT-1840/60/80/120-G-TW, Swing Over Bed: 18″Swing Over Cross Slide: 11″Distance Between Centers: 40″/60″/80″/119″Spindle Speed RPM Range: 20-1,600 RPMHole Through Spindle: 3.15″Spindle Nose: D1-8Motor HP: 10 ...more

160" SELF CLIMBING HIGH RISE WINDOW CLEANING SYSTEM, 13' CLEANING PATH, 13000 SQUARE FEET AN HOUR, 2GPM, 230 VOLT, 22.7 AMPS.

FEIN GRIT HORIZONTAL BELT SANDER, PRICE: Loaded on Truck, Our Warehouse, York, PA ………… $2,750.00, HMC Stock # 22136, Machine Serial No.: 0822194?? (tag torn), Machine Model No.: GIB9-90-01-003-00, New Date: 2007, Sanding Belt Width: 6", Powered Thru Feed Parts System, Vertical Adjustment of ...more

, For sale: Cushman 1034E2 used 10 lathe chuck with 3 jaws. Manufactured by Cushman Chuck Company, featuring a 2 center hole. Ideal for enhancing your tooling capabilities in a professional setting., Spec Sheet:, Cushman 1034E2 Lathe Chuck 10 3 Jaw, USED, Brand: Cushman Chuck Company, Type: Lathe Chuck, Jaws: 3 ...more

Used Approximately 105 Gallon Stainless Steel Tank, Capacity: 105 gallons, Dimensions: 36" dia. x 24" straight side, Flat, hinged top, dish bottom, Mounted on legs, _UNKNOWN_ 105 GALLON, Capacity. 105 gal, Diameter. 3', Height. 2', Type of stainless. Stainless Steel, Type Of Heads. Flat top, Dish Bottom ...more

Used Approximately 350 Gallon Stainless Steel Jacketed Mix Tank, Manufacturer: Lee Industries, Capacity: 350 gallons, National Board: 6168, Model: 350U9MS, Serial: C1126A2, Year: 1994, Internal rated full vacuum @ 250F, Jacket pressure: 125 psi @353F, Top, bridge-mounted agitator with, Dish top, Mounted on (4) ...more

SERIAL. 237881, MODEL. E, PIPE OUTSIDE DIAMETER. 6" TO 72", CUTTING SPEED. 35 TO 55 RPM, BEVEL ANGLE. 30 & 37.5 DEGREE, MATERIAL REMOVED.188", CUTS & BEVELS SIMULTANEOUS. YES, CFM REQUIRED. 100 @90 PSI, PNEUMATIC MOTOR. 3/4 HORSEPOWER, CUTS PIPE HORIZONTAL OR VERTICAL.

, Manufacturer: National, Model Number: LBP-32-120, Serial Number: 12222, Stock Number: 14053, s:, Newall DP700 2-Axis Digital Readout, Pendant control, Removable gap, 24-3/4” Front 4 Jaw chuck, 23-3/4 Rear 4 jaw chuck, Power rapids for longitudinal & cross, 2 speed tailstock - 1/1 and 1/4, Aloris Quick ...more

Working AreaTable set up area 83x20 in Table load capacity (max.) 4,400 lbs Number of T-slots 4 positions T-slots, spacing 0.8 in TravelsTravel X-axis 59.1 in Travel Y-axis 26 in Travel Z-axis 0 - 26 in Vertical Milling HeadSpindle speed (vertical) (12) 40 - 1,600 rpm Spindle mount ISO 50 Throat 24 in Vertical ...more

Used Approximately 50 Gallon Stainless Steel Tank, Capacity: 50 gallons, Dimensions: 30" dia. x 20" straight side, Dish top, dish bottom, _UNKNOWN_ 50 GALLON, Capacity. 50 gal, Diameter. 2.5', Height. 1.67', Type of stainless. Stainless Steel, Type Of Heads. Dish, Vertical/Horizontal. Vertical, Dimensions. 30" ...more

Stock #: 82982 Category: Vertical Motors HP: 60 RPM: 1765.00 Frame: K364TP16 Enclosure: TEFCBB Make: Electric Volts: 230/460 Service Factor: 1.15 Condition: Electrically O.K. Location: Toledo, OH.

Make: Bucher Unipektin, Model: C25, Year: 1900, Machine Location: Upon Request, Machine Overview, The Bucher Unipektin C25 is an industrial stainless rotary mill used to reduce fruit, root vegetable, and fibrous product prior to pressing or extraction. This unit s a vertical auger feed design with cutting drum ...more

Cincinnati Monoset Tool & Cutter Grinder, CINCINNATI MILACRON MONOSET CUTTER TOOL GRINDER, PRIVATE Rebuilt 1993tc' \l 1 Rebuilt 1993, S/N 2D1C5P-4AYear: 1964, STANDARD, CAPACITY, Work head:, Swing over main slide, max. dia. 12, Collet work dia. - max.1.25, - min. 0.12, Lead generated by spiral lead mechanism ...more

Stock #: 171260009, Location: UT, Brand: RedArt Technologies, Model: CNC Pro, Approx. Shipping Weight: 120 LBS, Approx. Shipping Dimensions: Box: 57"L x 16"W x 12"H, Engraving Area: 24" x 36", Engraving Depth: Up to 2", Spindle Speed: 0 - 24,000 RPM, Precision:.0006" Accuracy, Vertical ...more

ENTRY GUIDE, ENTRY FEED ROLLS. 2, VERTICAL ROLLS. 6, 3 OVER 3, INDIVIDUAL ADJUSTMENT, HORIZONTAL ROLLS. 6, 3 OVER 3, INDIVIDUAL ADJUSTMENT, EXIT FEED ROLLS, CONTROLS FWD/REV, VARIABLE SPEED, DRIVE MOTOR. 4 HP.

HOLZ-HER - EVOLUTION 7405: CNC Machining Center (Vertical) -- Flexible "Vertical" Machining Center can reach movement speeds of: 223 FPM (68 MPM) in "X" & "Y" axis; 49 FPM (15 MPM) in "Z" axis with total safety. -- Working CapacityMaximum part size for "X" axis: 126" (3,200 mm); "Y" axis: 36.2" (920 mm); max. part ...more