Trusted Since 1924
The World's Leading Online Marketplace for Used, New, and Surplus Industrial Machinery & Equipment ℠
Browse Wanteds & For Sales
Posted: September 29, 2026 at 10:55 AM
Industry: Transformers
Budget: $50,001 - $100,000
Description: 1500KVA-2000KVA 34.5KV - 480V Pad mounted, oil filtered, loop feed. new surplus or reconditioned. PAPER WORK NEEDED! Thank you.
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 29, 2026 at 10:30 AM
Industry: Other Electrical & Power Equipment
Description: ATH2FDA40100BSU 100 amp 208v 3ph Transfer Switch Cutler Replacement
NEED ASSAP QTY 1 NEW SURPLUS RECON OK
NEED ASSAP QTY 1 NEW SURPLUS RECON OK
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 29, 2026 at 9:47 AM
Industry: General Machinery & Equipment
Description: New or used 8' x 16 gauge handbrake. If used it must be late model in good condition. Prefers Tennsmith or National. Closer to Detroit the better.
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 29, 2026 at 9:28 AM
Industry: General Machinery & Equipment
Description: Moving Range: 100 × 100 mm 3.94 × 3.94" (electric)
1” 6.6 mega pixel monochrome CMOS … [Read more...]
1” 6.6 mega pixel monochrome CMOS … [Read more...]
10. 4” LCD monitor (XGA: 1024 × 768)
Wide-field measurement mode : 200 mm x 200 mm 7.87 × 7.87" (4x R50)
High-precision measurement mode : 125 × 125 mm 4.92 × 4.92"
Ambient temp: +10 to +35 °C 50 to 95 °F
Measurement accuracy (±2σ)
USB 3.1
4 ports (rear: 4)
USB 2.0 series
2 ports (front: 2)
Hard disk drive: 500 GB
Wide-field measurement mode : 200 mm x 200 mm 7.87 × 7.87" (4x R50)
High-precision measurement mode : 125 × 125 mm 4.92 × 4.92"
Ambient temp: +10 to +35 °C 50 to 95 °F
Measurement accuracy (±2σ)
USB 3.1
4 ports (rear: 4)
USB 2.0 series
2 ports (front: 2)
Hard disk drive: 500 GB
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 29, 2026 at 9:05 AM
Industry: General Machinery & Equipment
Description: Landis Cincinnati Series 350-20 Grinder for sale
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 29, 2026 at 9:02 AM
Industry: General Machinery & Equipment
Description: 6500-10000 Gallon Vertical SS storage tank. Flat bottom. East Coast Preferred.
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 29, 2026 at 9:01 AM
Industry: Circuit Breakers
Description: (10) Square D Powerpact 600 Amp Circuit Breakers---LJL36600U31X--New surplus in boxes--Best offer--Pictures available.
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 29, 2026 at 9:00 AM
Industry: General Machinery & Equipment
Description: Tesker Model 200 thread roller mfd 2018
Kinefac Model MC4
Kinefac Model MC4
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 29, 2026 at 8:05 AM
Industry: Other Electrical & Power Equipment
Description: Hello, Sales Team,
My name is Jake Lee from Hyundai MOBIS US Alabama, LLC. … [Read more...]
My name is Jake Lee from Hyundai MOBIS US Alabama, LLC. … [Read more...]
We currently have surplus industrial electrical and automation components that we are looking to sell.
The inventory includes various parts from manufacturers such as Allen-Bradley, Festo, SICK, Automation, Omron, Honeywell, Pilz, and others.
I have attached our parts list along with photos of some of the items currently in storage for your review.
Please review the attached information and let me know if your company
The inventory includes various parts from manufacturers such as Allen-Bradley, Festo, SICK, Automation, Omron, Honeywell, Pilz, and others.
I have attached our parts list along with photos of some of the items currently in storage for your review.
Please review the attached information and let me know if your company
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 29, 2026 at 7:28 AM
Industry: General Machinery & Equipment
Description: Max Temperature: 800°C (1472°F)
Heating Power: 96 kW (≈327,500 BTU/hr) … [Read more...]
Heating Power: 96 kW (≈327,500 BTU/hr) … [Read more...]
Temperature Differential: ±8°C
Usable Chamber Size: 150 cm W × 150 cm D × 150 cm H (59" × 59" × 59")
Total Chamber Size: 170 cm W × 170 cm D × 175 cm H (67" × 67" × 69")
Usable Chamber Volume: 3.37 m³ (119 ft³)
Load Capacity: 3 tons
460V, 3‑Phase
Electric resistance heating system
Digital temperature controller with ramp programming
3‑channel digital temperature recorder
(3) fixed thermocouples
(9) TUS ports
Usable Chamber Size: 150 cm W × 150 cm D × 150 cm H (59" × 59" × 59")
Total Chamber Size: 170 cm W × 170 cm D × 175 cm H (67" × 67" × 69")
Usable Chamber Volume: 3.37 m³ (119 ft³)
Load Capacity: 3 tons
460V, 3‑Phase
Electric resistance heating system
Digital temperature controller with ramp programming
3‑channel digital temperature recorder
(3) fixed thermocouples
(9) TUS ports
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 29, 2026 at 7:28 AM
Industry: General Machinery & Equipment
X-axis: 18.9"
Y-axis: 9"
Travel distance per hand- wheel rotation, X-axis: 0.2"
Travel distance per hand-wheel rotation, Y-axis: 0.2"
Travel distance per hand-wheel rotation, Z-axis: 0.04"
Scale ring division X-axis: 0.00079"
Scale ring division Y-axis: 0.00079"
Scale ring division Z-axis: 0.0002"
Roughness: >=063 μm Ra
230v/60hz/3ph
Exhaust vacuum
Work lamp
Balancing station
adjustable grinding vise
Grinding wheel flange
Operating tools
Y-axis: 9"
Travel distance per hand- wheel rotation, X-axis: 0.2"
Travel distance per hand-wheel rotation, Y-axis: 0.2"
Travel distance per hand-wheel rotation, Z-axis: 0.04"
Scale ring division X-axis: 0.00079"
Scale ring division Y-axis: 0.00079"
Scale ring division Z-axis: 0.0002"
Roughness: >=063 μm Ra
230v/60hz/3ph
Exhaust vacuum
Work lamp
Balancing station
adjustable grinding vise
Grinding wheel flange
Operating tools
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 10:03 PM
Industry: Other Electrical & Power Equipment
Description: PME10 S&C PSE-10-54400 FPE PAD MOUNTED GEAR
MANUAL AIR INSULATED GEAR 15 KV 600 AMP RATED S&C BULLETIN 665-30 … [Read more...]
MANUAL AIR INSULATED GEAR 15 KV 600 AMP RATED S&C BULLETIN 665-30 … [Read more...]
QUOTE WHAT YOU HAVE
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 7:14 PM
Industry: General Machinery & Equipment
Description: Liebherr LC-180 or CNC external gear hobber suitable for a 10-100 mm prototype external-gear application
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 5:07 PM
Industry: General Machinery & Equipment
Description: 5,000 RPM, 22.84" swing, 39.37" machining length, 16.14" Max Turning Dia., 9.84" Max Turning Dia. Lower Turret, X-Axis 10.24", Z-Axis 42.72", X(2)-Axis 6.3", Z(2)-Axis 39.96", 10" hydraulic chucks, 12/8-position turrets and tailstock high-pressure coolant, and OKUMA OSP-P300LA controls, hydraulic chucks and LNS dual chip conveyors.
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 5:05 PM
Industry: Processing Equipment
Price: 1500
Description: Manufacturer: Fisher Controls (Emerson)Model: Type N551 Series (ESV)Service: LPG & NH3Pressure Rating: 400 PSI / WOGCasting Number / Body Stamp: R061480230Date Stamp Code: 01DEC22Condition: Brand New Surplus (New Old Stock). It has original factory protective thread caps installed, no line wear, and pristine factory internals. Minor exterior storage paint scuffs only.I am looking to liquidate this item quickly. Please let me know if your team is actively buying this model and if you can provide
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 5:02 PM
Industry: General Machinery & Equipment
Description: 25 hp, 12,000 RPM, 157.5" x 106.3" x 19.7", BT 40, 40 ATC, with spindle chiller, coolant system & chip conveyor. **Financing Available**
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 5:00 PM
Industry: General Machinery & Equipment
Description: 2016 FPT Raid XL CNC Machining Center, bridge type, with Heidenhain control, laser tool measurement, powerful 18,000 RPM spindle, HSK-A-63 taper, 30-ATC, and robust 79"x63"x32" travel. Well-equipped including spindle chiller and dual chip augers. **Financing Available**
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 3:14 PM
Industry: General Machinery & Equipment
Description: Blanchard #18 grinder, good working condition
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 2:49 PM
Industry: General Machinery & Equipment
Description: Clausing Colchester 21" lathe x 60" or 80" centers, good condition, D1-8 Camlock, Taper Attachment and extra tooling a plus, Midwest location preferred
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 2:16 PM
Industry: General Machinery & Equipment
Description: Okuma MA-600HB 4 Axis Horizontal Machining Center (2010)
OSP P200MA CNC, 240 ATC, High Pressure Coolant Through Spindle
OSP P200MA CNC, 240 ATC, High Pressure Coolant Through Spindle
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 1:54 PM
Industry: General Machinery & Equipment
Description: Pat Mooney Upcut compound miter saw, min. 24" blade
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 1:34 PM
Industry: General Machinery & Equipment
Description: looking for equipment to balance air cooled VW engines, I think I just need a balancer for the crankshafts? these are 60's 70's engines 1600 to 2332 with 69m to 86mm stock cranks horizontal opposed engines. we build engines now with out of the box parts and we would like start balancing them. thanks Don
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 1:19 PM
Industry: General Machinery & Equipment
Description:
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 1:01 PM
Industry: General Machinery & Equipment
Budget: Over $100,000
Description: Need Doosan (DN) NHP 4000 or DMG NHX 4000
Must be 2017 or newer in nice condition … [Read more...]
Must be 2017 or newer in nice condition … [Read more...]
probing a plus
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 12:59 PM
Industry: General Machinery & Equipment
Budget: Over $100,000
MU5000 with Pallets would be ideal but will also
look at single table machines and
Genos M460-5AX or Genos M560 5AX
look at single table machines and
Genos M460-5AX or Genos M560 5AX
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 12:02 PM
Industry: General Machinery & Equipment
Description:
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 11:42 AM
Industry: Circuit Breakers
Description: Looking for (6) Finger clusters for GE PowerVac ground and test - 3000A with mounting stab
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 11:41 AM
Industry: Processing Equipment
Description: Need 1,000 gallon food grade SS tank, agitation, low pressure jacket, 30 psi internal.
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 11:38 AM
Industry: Processing Equipment
Description: need 3
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 11:31 AM
Industry: General Machinery & Equipment
Price: $6,500
Description: Kiwa Excel Model 4L Vertical Machining Center, Fanuc 10M Control, CAT40 Taper, Approx. 6,000 RPM, 30"X, 16"Y, 20"Z, 17" x 34" Table, In Shop Running.
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 11:29 AM
Industry: General Machinery & Equipment
Description: Looking for 15" 3-Jaw Chuck with A2-11 mount for Milltronics ML26 CNC Lathe.
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 11:17 AM
Industry: General Machinery & Equipment
Description: Yaskawa Motoman MA-1900 Robotic Welding Cell, With Yaskawa type YR-MA01900-A00 6-Axis Robot with 75" Reach, 3Kg Payload Capcity, Yaskawa DX100 Control, Miller Auto Axcess 300 DI Welding Power Supply, Hand-held Welder Remote, (2) Work/Fixture Tables Mounted on a Turn-table for Separate Set-up and Welding Cells, Video Available, LOW USAGE, New 2012.
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 10:35 AM
Industry: General Machinery & Equipment
Description: Doosan Daewoo DHC-400
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 10:04 AM
Industry: General Machinery & Equipment
Description: 10,000 Lbs. HUBTEX MSU 45 Multi-directional Electric Side-loader, New 2007
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 9:39 AM
Industry: General Machinery & Equipment
Description: Accucut 2,4,6 or 8 Station, must be ready to work
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 9:20 AM
Industry: General Machinery & Equipment
Description: Have customer with a need for a smaller bridge mill, 50" in the Y x 80" or so would be ideal. Y axis of 45"+ is a must, as well as thru spindle coolant. Do not send any quotes for mills without thru spindle coolant as they will not be considered. Also, 3 axis is fine.
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 9:09 AM
Industry: General Machinery & Equipment
Description: Okuma GP-26T CNC Cylindrical Grinder (2011)
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 9:08 AM
Industry: General Machinery & Equipment
Shear Strength: 50,000 PSI (22,679 kgs.)
Maximum Coil Weight: 10,000 Lbs. (4,535 kgs.)
Coil I.D.:
Entry: 16″ – 24″ (406 – 609 mm)
Recoiler: 20″ (508 mm)
Line Direction: Right to Left
Maximum Coil Weight: 10,000 Lbs. (4,535 kgs.)
Coil I.D.:
Entry: 16″ – 24″ (406 – 609 mm)
Recoiler: 20″ (508 mm)
Line Direction: Right to Left
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 9:07 AM
Industry: General Machinery & Equipment
SERIAL NUMBER: 35193
YEAR: 07-07-1999
SPECIFICATIONS:
Maximum Coil Weight: 20,000 Lbs. per side
Maximum Coil Width: 48″
Maximum Coil O.D.: 72″
Mandrel Expansion Range: 18.5″ – 23.25″
EQUIPPED WITH:
Coil Car
(2) Hold Down Arms
Hydraulic Unit
Motorized Turret, Hydraulic
Motorized Feed, Hydraulic
Hydraulic Expansion & Contraction
YEAR: 07-07-1999
SPECIFICATIONS:
Maximum Coil Weight: 20,000 Lbs. per side
Maximum Coil Width: 48″
Maximum Coil O.D.: 72″
Mandrel Expansion Range: 18.5″ – 23.25″
EQUIPPED WITH:
Coil Car
(2) Hold Down Arms
Hydraulic Unit
Motorized Turret, Hydraulic
Motorized Feed, Hydraulic
Hydraulic Expansion & Contraction
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 9:05 AM
Industry: General Machinery & Equipment
Description: Hurco VMX 30Ui 5 Axis Vertical Machining Center (2020)
5th Axis Trunnion, 40 ATC Side Mount, High Pressure Coolant Through Spindle, Chip Conveyor
5th Axis Trunnion, 40 ATC Side Mount, High Pressure Coolant Through Spindle, Chip Conveyor
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 9:04 AM
Industry: General Machinery & Equipment
SERIAL NUMBER: 28921
SPECIFICATIONS:
Maximum Tube Diameter: 3" (76 mm)
Minimum Tube Diameter: 3/4" (19 mm)
Maximum Bar Capacity: 2" (50 mm)
Minimum Bar Capacity: 3/4" (19 mm)
Total Rolls: 7
Driven Rolls: 2 (5" O.D. x 13 Long)
Idle Rolls: 5 (4" O.D. x 6" Long)
Maximum Speed: 393 FPM (120 M/Min.)
Motor: 400/440/3/50
CONDITION: Good
SPECIFICATIONS:
Maximum Tube Diameter: 3" (76 mm)
Minimum Tube Diameter: 3/4" (19 mm)
Maximum Bar Capacity: 2" (50 mm)
Minimum Bar Capacity: 3/4" (19 mm)
Total Rolls: 7
Driven Rolls: 2 (5" O.D. x 13 Long)
Idle Rolls: 5 (4" O.D. x 6" Long)
Maximum Speed: 393 FPM (120 M/Min.)
Motor: 400/440/3/50
CONDITION: Good
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 7:28 AM
Industry: General Machinery & Equipment
Z-Axis: 20"
Power: 20 hp
RPM: 10,000 RPM
# ATC: 24
Taper: CAT-40
Table-W: 12.75"
Table-L: 20"
# Axis: 3
Chip auger
Coolant through spindle
10,000 rpm spindle
Rotary dual pallet changer
4th axis drive installed
Power: 20 hp
RPM: 10,000 RPM
# ATC: 24
Taper: CAT-40
Table-W: 12.75"
Table-L: 20"
# Axis: 3
Chip auger
Coolant through spindle
10,000 rpm spindle
Rotary dual pallet changer
4th axis drive installed
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 7:28 AM
Industry: General Machinery & Equipment
Description: Total 3D Scan Volume (X x Y x Z): 4.92" × 4.92" × 1.65"
Internal Work Envelope: 12" x 12" x 8" … [Read more...]
Internal Work Envelope: 12" x 12" x 8" … [Read more...]
Standard Focal Distance: 7.44"
Laser Wavelength: 355 nm
Laser Power Output: 3 W
Cooling Method: Forced Air Cooling
Workstation Type: Class 1 Laser Safety Enclosure
Beam Control: 3-Axis Simultaneous Scanning
Power Requirements: 240 VAC, 60 Hz
Keyence MD-U Series Laser Controller Unit
Keyence KE-W1 Class 1 Safety Enclosure
Keyence MD-U1000C 3-Axis UV Laser Marker Head
Laser Wavelength: 355 nm
Laser Power Output: 3 W
Cooling Method: Forced Air Cooling
Workstation Type: Class 1 Laser Safety Enclosure
Beam Control: 3-Axis Simultaneous Scanning
Power Requirements: 240 VAC, 60 Hz
Keyence MD-U Series Laser Controller Unit
Keyence KE-W1 Class 1 Safety Enclosure
Keyence MD-U1000C 3-Axis UV Laser Marker Head
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 28, 2026 at 7:28 AM
Industry: General Machinery & Equipment
Table Lift Capacity: 2000 lbs
HD 7.5HP Fume Pump
$200,000 when purchased new
3 Phase
10" Adjustable Table Heigh w/ 2-zone downdraft table
Integrated Industrial grade computer with Job Manager Interface
Remote Pendant w/ pendant pedestal
Laser Chiller
I-Laser Vision Alignment System
Hydraulic Lift for table
510 CO2 Honeycomb Table Inserts
HD 7.5HP Fume Pump
$200,000 when purchased new
3 Phase
10" Adjustable Table Heigh w/ 2-zone downdraft table
Integrated Industrial grade computer with Job Manager Interface
Remote Pendant w/ pendant pedestal
Laser Chiller
I-Laser Vision Alignment System
Hydraulic Lift for table
510 CO2 Honeycomb Table Inserts
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 27, 2026 at 7:22 PM
Industry: Processing Equipment
Price: 8500
Valve Configuration: Schedule 80
Pressure Class: Class 300
Connection: Flanged
Body Material: Cast CF8M Stainless Steel
Ball Material: Borided Inconel 718
Seat Material: Borided Inconel 718
Ball Type: Regular Ball / On-Off
Seals: 316 Stainless Steel / Graphite
Stem Packing: Dual Graphite Packing
Bolting: B8 / Grade 8
Original Gosco production records are traceable using the individual 49819-X identification numbers. Certificates may be available.
Pressure Class: Class 300
Connection: Flanged
Body Material: Cast CF8M Stainless Steel
Ball Material: Borided Inconel 718
Seat Material: Borided Inconel 718
Ball Type: Regular Ball / On-Off
Seals: 316 Stainless Steel / Graphite
Stem Packing: Dual Graphite Packing
Bolting: B8 / Grade 8
Original Gosco production records are traceable using the individual 49819-X identification numbers. Certificates may be available.
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 27, 2026 at 1:42 PM
Industry: General Machinery & Equipment
Price: Best offer
Description: Relief valve size 4" x 6" - 175 PSI - 45,832 PPH - Dresser - Consolidated - Allied set 3-7-91 - steam, air, gas, liquid.
Possibly unused. … [Read more...]
Possibly unused. … [Read more...]
Consolidated type 1905NC - 2
serial # TJ13188
Set by Allied, Chicago - 3 - 7 -91
AV 199594
serial # TJ13188
Set by Allied, Chicago - 3 - 7 -91
AV 199594
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 27, 2026 at 12:38 PM
Industry: Transformers
Price: Best offer
Volts by request
Located Western PA.
75 K Hammond 1 ph
( Two ) 45 K GE 3 ph
5 K Cutler Hammer
25 K Virginia 3 ph 10,000/1,000
100 K VAF 3 ph
139.5 K Energy 3 ph
75 K Federal Pacific 3 ph
25 K Cutler Hammer 1 ph
45 K Sorgel 3 ph
25 K GE1 ph (no voltage)
15 K Hammond 1 ph
75 K ? 3 ph
45 K GE 3 ph
7.5 K Acme 1 ph
30 K Uptegraff 3 ph
25 K GEI ph ?/208
(3 ) 45 K West. 3 ph
45 K MG 3 ph
75 K SQ D 3 ph
45 K GE 3 ph
30 K HPS 3 ph
(2) 8 K EMB 500/400
45K SQ D 3 ph
Located Western PA.
75 K Hammond 1 ph
( Two ) 45 K GE 3 ph
5 K Cutler Hammer
25 K Virginia 3 ph 10,000/1,000
100 K VAF 3 ph
139.5 K Energy 3 ph
75 K Federal Pacific 3 ph
25 K Cutler Hammer 1 ph
45 K Sorgel 3 ph
25 K GE1 ph (no voltage)
15 K Hammond 1 ph
75 K ? 3 ph
45 K GE 3 ph
7.5 K Acme 1 ph
30 K Uptegraff 3 ph
25 K GEI ph ?/208
(3 ) 45 K West. 3 ph
45 K MG 3 ph
75 K SQ D 3 ph
45 K GE 3 ph
30 K HPS 3 ph
(2) 8 K EMB 500/400
45K SQ D 3 ph
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 27, 2026 at 11:59 AM
Industry: Generators & Engines
We are a used generator buyer from UAE and want to buy regularly recurring refurbished second hand generators 1000 kv,1500kv,2000kv Caterpillar, Cummins, Perkins, made in usa/uk and appreciate to share the economical price including shipment to jebel ali port and transit time and payment terms.
Email:[email protected]
+971569744497 WhatsApp/call
Email:[email protected]
+971569744497 WhatsApp/call
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 27, 2026 at 11:28 AM
Industry: General Machinery & Equipment
Swing Over Cross Slide: 11.8 in
Max Turning Diameter: 10.2 in
Max Turning Length: 18 in
Max Bar Capacity: 2.0 in
Spindle Speed: 5k RPM
Spindle Motor: 20 HP
Spindle Bore: 2.41 in
Standard Chuck Size: 8 in 3-jaw hydraulic chuck
Turret Stations: 12 positions
Parts catcher
Tail stock
Tool setter
3-jaw chuck
ATS Md. A6-S20HS collet nose
Coolant
Chip conveyor
Fanuc 21iT CNC controls
Max Turning Diameter: 10.2 in
Max Turning Length: 18 in
Max Bar Capacity: 2.0 in
Spindle Speed: 5k RPM
Spindle Motor: 20 HP
Spindle Bore: 2.41 in
Standard Chuck Size: 8 in 3-jaw hydraulic chuck
Turret Stations: 12 positions
Parts catcher
Tail stock
Tool setter
3-jaw chuck
ATS Md. A6-S20HS collet nose
Coolant
Chip conveyor
Fanuc 21iT CNC controls
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 27, 2026 at 9:28 AM
Industry: General Machinery & Equipment
Feed Speed: ~15 FPM
Passline Height: 33"
Abrasive Belt Size: 37" x 75"
Number of Heads: 1 single-head configuration
Main Sanding Head Motor: 20 HP
Electrical Requirement: 230V / 3-Phase / 60 Hz
Separated Wet Coolant & Filtration Tank
Passline Height: 33"
Abrasive Belt Size: 37" x 75"
Number of Heads: 1 single-head configuration
Main Sanding Head Motor: 20 HP
Electrical Requirement: 230V / 3-Phase / 60 Hz
Separated Wet Coolant & Filtration Tank
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 27, 2026 at 9:28 AM
Industry: General Machinery & Equipment
Model - 210-HTG-12220-1084
Controller - Demag NC 4
Clamp Style - Toggle
Platten Size - 22" x 22"
Distance Between Tie Bars - 32" x 32"
Hydraulic Knockout - Yes
Core Pull - Yes
Serial Number - 1084
Including any extra tooling/dies
Controller - Demag NC 4
Clamp Style - Toggle
Platten Size - 22" x 22"
Distance Between Tie Bars - 32" x 32"
Hydraulic Knockout - Yes
Core Pull - Yes
Serial Number - 1084
Including any extra tooling/dies
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 26, 2026 at 4:36 PM
Industry: Circuit Breakers
Description: ABB ZED1600RP ISDA112850R1 1600 AMP RATING PLUG E2N BREAKER
NEED A FEW OF THESE
NEED A FEW OF THESE
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 26, 2026 at 9:37 AM
Industry: General Machinery & Equipment
Description: Accucut or Similar 4,6 or 8 Spindle must be good
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 26, 2026 at 9:28 AM
Industry: General Machinery & Equipment
Max Turning Diameter - 10.3"
Max Turning Length - 20"
Distance Between Centers - 24"
Bar Capacity - 2"
Spindle Bore - 3"
X-Axis Travel - 8.45"
Z-Axis Travel - 20"
Rapids - 710 IPM
Full C-Axis
Programmable Hydraulic Tailstock
Automatic Tool Presetter
Automatic Door
Chip Conveyor
High-Intensity Work Light
Coolant System With Pump
Hydraulic Power Unit
Chuck And Tailstock Pressure Gauge Panel
Max Turning Length - 20"
Distance Between Centers - 24"
Bar Capacity - 2"
Spindle Bore - 3"
X-Axis Travel - 8.45"
Z-Axis Travel - 20"
Rapids - 710 IPM
Full C-Axis
Programmable Hydraulic Tailstock
Automatic Tool Presetter
Automatic Door
Chip Conveyor
High-Intensity Work Light
Coolant System With Pump
Hydraulic Power Unit
Chuck And Tailstock Pressure Gauge Panel
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 26, 2026 at 9:28 AM
Industry: General Machinery & Equipment
Description: Diameter Range (ID) – Manual Stroking - 0.060″ – 6.50″
Diameter Range (ID) – Power Stroking - 0.060″ – 4.00″ … [Read more...]
Diameter Range (ID) – Power Stroking - 0.060″ – 4.00″ … [Read more...]
Automatic Sizing - 1.25″ – 2.00″
Stroke Length - 0.236″ – 6.70″
Spindle Speeds (Infinitely Variable) - 200 – 3000 RPM
Stroke Rate - 60 – 500 SPM
Spindle Motor - 5.5 HP
Stroker Motor - 1.5 HP
Pump Motor - 0.5 HP
Coolant Flow - 3 Gallons/Minute
Coolant Capacity - 32 Gallons
Misc Tooling
Auto Stone Wear Compensation
Feed Regulator
Stroke Length - 0.236″ – 6.70″
Spindle Speeds (Infinitely Variable) - 200 – 3000 RPM
Stroke Rate - 60 – 500 SPM
Spindle Motor - 5.5 HP
Stroker Motor - 1.5 HP
Pump Motor - 0.5 HP
Coolant Flow - 3 Gallons/Minute
Coolant Capacity - 32 Gallons
Misc Tooling
Auto Stone Wear Compensation
Feed Regulator
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 26, 2026 at 9:28 AM
Industry: General Machinery & Equipment
Y-Axis: 62.9"
Z-Axis: 4.7"
Max Workpiece Weight: 2,050 lbs
Rapid Traverse Speed: 4,724 IPM
Laser Type: Fast Axial Flow CO2
Output Power: 4 kW
Maximum Cutting Thickness: Mild Steel (1"), Stainless Steel (0.5") & Aluminum (0.5")
Dual Pallet Shuttle Table System
40CF-R CO2 Resonator Unit
External Industrial Water Chiller
Z-Axis: 4.7"
Max Workpiece Weight: 2,050 lbs
Rapid Traverse Speed: 4,724 IPM
Laser Type: Fast Axial Flow CO2
Output Power: 4 kW
Maximum Cutting Thickness: Mild Steel (1"), Stainless Steel (0.5") & Aluminum (0.5")
Dual Pallet Shuttle Table System
40CF-R CO2 Resonator Unit
External Industrial Water Chiller
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 7:04 PM
Industry: General Machinery & Equipment
Price: best offer
Description: Good afternoon,
We have an uninstalled industrial packaged boiler available for immediate sale/buyout and wanted to check your current inventory acquisition interest. … [Read more...]
We have an uninstalled industrial packaged boiler available for immediate sale/buyout and wanted to check your current inventory acquisition interest. … [Read more...]
Vessel Details:
- Manufacturer: Cleaver-Brooks
- Model: CB700-100
- HP Capacity: 100 HP (4,184,000 BTU/HR Input)
- Serial Number: L-67757
- Manufacture Date: July 10, 1979
- Max Pressure: 15 PSI (Low-Pressure Steam/Hot Water)
- Fuel Type: Natural Gas
- Electrical: 460V / 3 Phase / 60Hz
- System Upgrades: Retrofitted Fireye Flame
- Manufacturer: Cleaver-Brooks
- Model: CB700-100
- HP Capacity: 100 HP (4,184,000 BTU/HR Input)
- Serial Number: L-67757
- Manufacture Date: July 10, 1979
- Max Pressure: 15 PSI (Low-Pressure Steam/Hot Water)
- Fuel Type: Natural Gas
- Electrical: 460V / 3 Phase / 60Hz
- System Upgrades: Retrofitted Fireye Flame
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 5:57 PM
Industry: Circuit Breakers
Description: GE AKR4000 AMP BREAKER LIFTING DEVICE ANY CONDITION
QTY 1
QTY 1
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 5:55 PM
Industry: Circuit Breakers
Description: GE AKR4000 AMP BREAKER LIFTING DEVICE ANY CONDITION
QTY 1
QTY 1
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 4:52 PM
Industry: General Machinery & Equipment
Description: Zeiss Model DuraMax 5/5/5 Coordinate Measuring Machine CMM (2013)
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 4:49 PM
Industry: General Machinery & Equipment
Description: Ermaksan ER 4000 6000 Watt Fibermak CNC Fiber Laser (2019)
Momentum Gen-3
Momentum Gen-3
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 1:59 PM
Industry: General Machinery & Equipment
Price: 2500
Description: Lapmaster 24 lapping machine with accessories. Unit was formerly in use at a Honeywell aerospace facility prior to being acquired by my former FAA repair station. The slurry tank was damaged years ago during transport but the unit should otherwise be serviceable and has been in storage for some time. The unit includes: 3 condition rings, 1 pressure plate, 2 smaller weighted plates, two rings, and a Massive C Clamp. Located in Boynton Beach, FL 33426
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 1:11 PM
Industry: Processing Equipment
Price: best offer
Description: These are flexco ( Hing pins ) for conveyer belts,
FLEXCO Bare armored stainless cable … [Read more...]
FLEXCO Bare armored stainless cable … [Read more...]
'3/8"" Dia.Hinge Pins
several available
several available
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 12:49 PM
Industry: General Machinery & Equipment
Description: Amada Pega 357 w/ 04PC, mid - late 90's
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 12:45 PM
Industry: Other Electrical & Power Equipment
Budget: $10,001 - 50,000
Description: GM77511-7-KCB Alternator Asm,7M4288,600V,SAE 00/21 Marathon 8288-GM77511-7 or
10201009811-KCB ALT-KH07770TO4D-ST-6-BS2800W480V-L56HBI Leroy Somer LS842 L75 480V Alternator or … [Read more...]
10201009811-KCB ALT-KH07770TO4D-ST-6-BS2800W480V-L56HBI Leroy Somer LS842 L75 480V Alternator or … [Read more...]
10201009912-KCB ALT-KH07770TO4D-ST-6-BS2800W600V-L56HBI Leroy Somer LS842 L75 600V or
A-328099 Alternator assembly 400KW, 480V Marathon 433RSL4021BF
A-328099 Alternator assembly 400KW, 480V Marathon 433RSL4021BF
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 12:35 PM
Industry: Motors - A.C. & D.C.
Description: Lincoln Electric motor, LM15263, 100 Hp 1800 Rpm., 405TC Fr., TEFC, 230/460v., 60 Hz. mounting feet not used, can be footless, any condition that can be rebuilt or rewound. Must be Lincoln steel frame TEFC to fit application.
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 12:19 PM
Industry: General Machinery & Equipment
Description:
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 11:19 AM
Industry: General Machinery & Equipment
Description: Yaskawa Motoman MA-1900 Robotic Welding Cell, With Yaskawa type YR-MA01900-A00 6-Axis Robot with 75" Reach, 3Kg Payload Capcity, Yaskawa DX100 Control, Miller Auto Axcess 300 DI Welding Power Supply, Hand-held Welder Remote, (2) Work/Fixture Tables Mounted on a Turn-table for Separate Set-up and Welding Cells, Video Available, LOW USAGE, New 2012.
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 11:17 AM
Industry: General Machinery & Equipment
Price: Best Offer
Description: Doosan MV3016L Vert. Machining Center, New 2007. Fanuc 0i-MC Control, Remote MPG, 8,000 RPM, CAT-40, 30 Side-mount ATC, 17" x 36" Table, Rigid Tapping
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 11:14 AM
Industry: General Machinery & Equipment
Description: Hermann Kolb 11' x 30" Radial Drill, 5' x 14' Tee-slotted Base, 28 – 1122 RPM, #6 MT, 11' Max. Height (Spindle Nose to Base), Power Elevation, Power Clamping,
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 11:04 AM
Industry: General Machinery & Equipment
Price: 21,500
Description: Koike Aronson Mastergraph industrial CNC plasma cutting system in operating condition. Machine is currently under power and can be demonstrated cutting.
Heavy-duty gantry-style system suitable for industrial steel fabrication and production cutting. Machine includes CNC-controlled cutting gantry, plasma cutting equipment, multiple torch stations and heavy-duty slat cutting table. … [Read more...]
Heavy-duty gantry-style system suitable for industrial steel fabrication and production cutting. Machine includes CNC-controlled cutting gantry, plasma cutting equipment, multiple torch stations and heavy-duty slat cutting table. … [Read more...]
The machine is currently in service, and the accompanying video shows the system actively cutting material.
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 10:33 AM
Industry: Circuit Breakers
Description: 40 x TA1200NB1
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 9:13 AM
Industry: Generators & Engines
Price: best offer
Description: Exchange crankshafts in stock. Ariel JGC/6, JGK/4 (2), JGK/2. CAT 3306, 3512B (2), 3516, 3612. Waukesha L7042 T-drilled (3), VHP 1200 rpm angle drilled, L5790G/L7042G, H24 (2), 9390G, P9390. White Superior 6G825, 8G825, 8GTL825, RAM 52, RAM 54, WH64. Ingersoll Rand RDS4, Knight KOA-2, VRG330, F817G. Part numbers and photos on request. Contact Jason McNicho
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 8:00 AM
Industry: General Machinery & Equipment
Description: Lincoln Electric Torchmate 4510 5' X10' Plasma Cutting
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 7:28 AM
Industry: General Machinery & Equipment
Min Material Thickness: 30ga
Max Material Thickness: 14ga
Line Speed: 80–255 ft/min
Main Motor: 10 HP
Max Coil OD: 48"
Coil ID: 20"
Max Coil Weight: 2,500 lbs
Butt joint spiral seam with flying crimp seam lock
Materials Supported: Galvanized Steel (G‑90/G‑60), Stainless Steel, Aluminum, Light‑Gauge Coil Stock
Heavy Duty Tooling Set
Light Duty Tooling Set
Quick change head mount system
Form Roll Unit 1/3
Form Roll Unit No. 4
Flying Crimper Assembly
Max Material Thickness: 14ga
Line Speed: 80–255 ft/min
Main Motor: 10 HP
Max Coil OD: 48"
Coil ID: 20"
Max Coil Weight: 2,500 lbs
Butt joint spiral seam with flying crimp seam lock
Materials Supported: Galvanized Steel (G‑90/G‑60), Stainless Steel, Aluminum, Light‑Gauge Coil Stock
Heavy Duty Tooling Set
Light Duty Tooling Set
Quick change head mount system
Form Roll Unit 1/3
Form Roll Unit No. 4
Flying Crimper Assembly
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 7:28 AM
Industry: General Machinery & Equipment
Description: 37 Process Tanks (Polypropylene & 316L Stainless Steel)
Electrified Saddles (Electroclean + Plating Stations) … [Read more...]
Electrified Saddles (Electroclean + Plating Stations) … [Read more...]
Non‑Electrified Saddles (All other stations)
Anodes & Baskets (Titanium micro‑mesh baskets)
3 Rectifiers
1,500A Electroclean
1,500A Zinc
500A Nickel
Main MCC
Lift Stations (2 × 100 gal)
Pump & Filter System
1.5 HP SS Soak Clean Recirculation Pump
1.5 HP SS Electroclean Recirculation Pump
3 MAPCO air scrubbers
Air scrubber control box
Dry / Cure Oven
Hoist & Runway System
Anodes & Baskets (Titanium micro‑mesh baskets)
3 Rectifiers
1,500A Electroclean
1,500A Zinc
500A Nickel
Main MCC
Lift Stations (2 × 100 gal)
Pump & Filter System
1.5 HP SS Soak Clean Recirculation Pump
1.5 HP SS Electroclean Recirculation Pump
3 MAPCO air scrubbers
Air scrubber control box
Dry / Cure Oven
Hoist & Runway System
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 25, 2026 at 7:28 AM
Industry: General Machinery & Equipment
Max Reach: 72"
Wrist Diameter: 2.24" ID
Motion Range: 340 Degree - 370 Degree
Controller: R-30iB Plus Controller
Enclosure Dimensions: 10' x 16'
Table Dimensions: 7' x 8'
Work Zone: 4' x 8'
Table Capacity: Approx 5,000Lbs
Grinding Attachment
Full Enclosure
Wrist Diameter: 2.24" ID
Motion Range: 340 Degree - 370 Degree
Controller: R-30iB Plus Controller
Enclosure Dimensions: 10' x 16'
Table Dimensions: 7' x 8'
Work Zone: 4' x 8'
Table Capacity: Approx 5,000Lbs
Grinding Attachment
Full Enclosure
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 10:18 PM
Industry: Circuit Breakers
Description: SPB 100 2000 AMP PWR BRAKE COMPACT FRAME BI MANUALLY OPERATED
ANY TRIP OR NONE UNIT TO BE RETROFITTED EOK CONDITION … [Read more...]
ANY TRIP OR NONE UNIT TO BE RETROFITTED EOK CONDITION … [Read more...]
QTY 2-4 UNITS
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 9:56 PM
Industry: General Machinery & Equipment
Description: USED FANUC ROBOT M200ic
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 9:32 PM
Industry: General Machinery & Equipment
Y 30”
Z 30”
Cat 50 Spindle
10K RPM
pref High speed look ahead
Fanuc or Mazatrol control preferred
Z 30”
Cat 50 Spindle
10K RPM
pref High speed look ahead
Fanuc or Mazatrol control preferred
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 4:41 PM
Industry: Generators & Engines
Price: 2,200,000.00
Stock Number ED01142
Hours 10
Manufacturer Cummins
Model C2000N6CB
kW Power Rating 2000
Power Factor .8
Voltage 480
Phase 3
Enclosure Sound DBA65 @23ft
Fuel Natural Gas
Engine Model QSV91G
NOx 0.05g/hp-hr
CO 0.17 g/hp-hr (93% reduction)
NMHC 0.2 g/hp-hr (50% reduction)
Hours 10
Manufacturer Cummins
Model C2000N6CB
kW Power Rating 2000
Power Factor .8
Voltage 480
Phase 3
Enclosure Sound DBA65 @23ft
Fuel Natural Gas
Engine Model QSV91G
NOx 0.05g/hp-hr
CO 0.17 g/hp-hr (93% reduction)
NMHC 0.2 g/hp-hr (50% reduction)
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 4:24 PM
Industry: General Machinery & Equipment
Price: best offer
Description: 2010 super clean Royal Master 12x4 centerless grinder out of optical company
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 3:45 PM
Industry: Motors - A.C. & D.C.
Description: Needs to be able to ship in the next 3 weeks. 400HP or larger. 2 pole,460V-Preferably TEFC but open to WPI or WPII, 5011VP with 30.5" P base VSS motor
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 3:37 PM
Industry: General Machinery & Equipment
Budget: $10,001 - 50,000
Description: Brother TC-32B Drilling & Tapping Machine or Similar Model, Ganesh, Fanuc?
2011 or newer.
2011 or newer.
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 2:28 PM
Industry: Circuit Breakers
Description: Looking for an ABB SACE E3S-A32. Manually operated bolt in. PR121/P trip unit LI functions w/ 3000A rating plug. 120/127VDC/DC shunt trip and aux switch
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 2:01 PM
Industry: Generators & Engines
Price: 4,000
sound attenuated
120/240 single phase
nema 3 ats goes with it
low hrs less than 1000
120/240 single phase
nema 3 ats goes with it
low hrs less than 1000
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 1:59 PM
Industry: Transformers
69 KV grdy secondary
quote what you have
quote what you have
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 1:40 PM
Industry: General Machinery & Equipment
Description: Semi Load Quantity of Black Beauty 4000 blasting media FOB West Virginia
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 1:33 PM
Industry: General Machinery & Equipment
Price: Best offer
Description: Unused Walk-in / process oven for curing and drying non-flammable loads. 1million btus - 650 F
LEWCO … [Read more...]
LEWCO … [Read more...]
Model:
NS-EWR06FD-72-240-84
Condition:
New - In-Stock
Year:
2017
Status:
For Sale
Country:
United States
Description
Never used Walk-in / process oven for curing and drying non-flammable loads. 1million btus - 650 F
Two are available
Specifications
Workspace Dimensions: 72” Width × 241” Length × 84” Height (provides roughly 840 cubic feet of volume).
NS-EWR06FD-72-240-84
Condition:
New - In-Stock
Year:
2017
Status:
For Sale
Country:
United States
Description
Never used Walk-in / process oven for curing and drying non-flammable loads. 1million btus - 650 F
Two are available
Specifications
Workspace Dimensions: 72” Width × 241” Length × 84” Height (provides roughly 840 cubic feet of volume).
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 12:55 PM
Industry: General Machinery & Equipment
Description: Miyano BNE or BND 2000-2010 machine
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 11:32 AM
Industry: General Machinery & Equipment
Description: Hermann Kolb 11' x 30" Radial Drill, 5' x 14' Tee-slotted Base, 28 – 1122 RPM, #6 MT, 11' Max. Height (Spindle Nose to Base), Power Elevation, Power Clamping, VIDEO AVAILABLE.
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 11:30 AM
Industry: General Machinery & Equipment
Description: Omax Model 5555 Waterjet Machine, Omax Control, 55,000 PSI Pump, 55" x 54" Tavels, 65" x 80" Tank, 40 Hp, Tilt-a-Jet Head, Garnet Tank, Filters, Quantity of Garnet, Well Maintained, New 2008.
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 11:28 AM
Industry: General Machinery & Equipment
Price: Best Offer
Description: Doosan MV3016L Vert. Machining Center, New 2007. Fanuc 0i-MC Control, Remote MPG, 8,000 RPM, CAT-40, 30 Side-mount ATC, 17" x 36" Table, Rigid Tapping
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 11:19 AM
Industry: Other Electrical & Power Equipment
Price: Reasonable offers only
Description: Unused 2022 Vertiv Liebert DS077AUA + Matching Condenser for Sale
Hello, … [Read more...]
Hello, … [Read more...]
I have an unused/excellent-condition Vertiv Liebert precision cooling system for sale:
• Indoor unit: Model DS077AUA100865A (77 kW / 22-ton, downflow, air-cooled, semi-hermetic 4-step, R-407C, 460 V 3-phase 60 Hz) Serial: N22C000393 | Date code: C-2022
• Matching remote air-cooled condenser: Unused (same era)
Both units are in unused/excellent condition. Located in NJ
• Indoor unit: Model DS077AUA100865A (77 kW / 22-ton, downflow, air-cooled, semi-hermetic 4-step, R-407C, 460 V 3-phase 60 Hz) Serial: N22C000393 | Date code: C-2022
• Matching remote air-cooled condenser: Unused (same era)
Both units are in unused/excellent condition. Located in NJ
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 11:19 AM
Industry: General Machinery & Equipment
Description: 4" Tos W100A Horizontal Boring Mill, 44” Vertical, 63” Cross, 49” Saddle, Facing Head, Tail Sock, Tooling, 49” x 49” Built In Power Rotary Table, 4 Axis DRO
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 11:17 AM
Industry: General Machinery & Equipment
Description: Poreba, Model TR-100B, Heavy Duty Gap Bed Engine Lathe, 42" Swing, 49" Swing in Gap, 20'9" Centers, 630 RPM, 4.25" Spindle Bore, 36" 4-Jaw, (2) 25" Steadies, Inch/Metric
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 11:16 AM
Industry: General Machinery & Equipment
Description: MVD 6Kw Laser, 5' x 10', Dual Pallet Shuttle Table, Dust Collector, Nesting Software, Camera Cutting Monitoring, Very Low Hours
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 10:32 AM
Industry: General Machinery & Equipment
Description: customer looking for small die heads for Hardinge
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 10:21 AM
Industry: Processing Equipment
Price: Best Offer
Description: A fire suppression bottle weighing around 70-100 pounds. Seems to contain HALON and NITROGEN pressurized.
Requested by Manufacturer:
Registered users login here to see contact info OR request access if not registered.
Posted: September 24, 2026 at 10:05 AM
Industry: General Machinery & Equipment
Distance Btw Centers - 36"
Upper X-Axis - 5.94"
Lower X-Axis - 9.05"
Upper Y-Axis - ±1.38" (2.76" Total)
Upper/Lower Z-Axis - 17.32" Each
B-Axis (Sub Spindle) -25.59"
C-Axis (Both Spindles) - 360°/0.001° Resolution
6,000 RPM
20 HP Peak/15 HP Continuous
X-Axis Rapid - 630 IPM
Y-Axis Rapid - 236 IPM
Z-Axis Rapid - 1,573 IPM
B-Axis Rapid - 1,573 IPM
Through Holder Coolant Lines
Dual High Pressure Coolant Pumps
Coolant Tank, Chip Conveyor w/ Hopper
Upper X-Axis - 5.94"
Lower X-Axis - 9.05"
Upper Y-Axis - ±1.38" (2.76" Total)
Upper/Lower Z-Axis - 17.32" Each
B-Axis (Sub Spindle) -25.59"
C-Axis (Both Spindles) - 360°/0.001° Resolution
6,000 RPM
20 HP Peak/15 HP Continuous
X-Axis Rapid - 630 IPM
Y-Axis Rapid - 236 IPM
Z-Axis Rapid - 1,573 IPM
B-Axis Rapid - 1,573 IPM
Through Holder Coolant Lines
Dual High Pressure Coolant Pumps
Coolant Tank, Chip Conveyor w/ Hopper
Requested by Dealer:
Registered users login here to see contact info OR request access if not registered.
