1 - 50 of 97 listings
Baker #A, Band Resaw, 6" cut H x unlimited L, 7" x 7" material, 120 FPM, 28" wheel diameter, 13'-2" L x 1" or 1-1/4" width x 0.035" blade, 20 HP, 2026, new
Ex-Factory | Charlotte, NC
Category: Resaw Band Saws
Seller: Ex-Factory
Location: Charlotte, NC
Mfr: Baker
Model: A
Year: 2026
BAKER A Band Resaw 1/4" to 6" (6 mm-152 mm) cutting height x unlimited lengths; accepts up to 7" x 7" max. incoming material with conveyor set at zero degrees.: -- Fully variable feed speeds from 0 to 120 FPM and controlled by a hydraulic flow control valve; feed speeds relative to width of cut and hardness of ...more
Baker #A, Horizozntal Band Re-saw, w/Slide return, 7" x 7" timber capacity, 120 FPM, 6" width, 20 HP, 28" diameter band wheel, 2026, new
Ex-Factory | Charlotte, NC
Category: Resaw Band Saws
Seller: Ex-Factory
Location: Charlotte, NC
Mfr: Baker
Model: A
Year: 2026
BAKER - A,.Single-Head Resaw w/Hydraulic Powered Return - 6" x 12" Cut Cap.: -- Max. 6" Wide x 12" Tall timber cap. (with conveyor set at zero) w/Slide Return (photo shows powered return); hydraulic variable feed speed rate 0 - 120 FPM 6";-wide, hydraulically-driven powered conveyor with rough top belting. -- : -- 20 ...more
Baker #A, Single Head, Resaw, 3ph, 20 HP TEFC, 6" conveyor, NEMA 12 panel, 240/480 V., New
RT Machine | Hughesville, PA
Category: Resaw Band Saws
Seller: RT Machine
Location: Hughesville, PA
Mfr: Baker
Model: A
Baker Model A Single Head Resaw, 3 PH 20 HP TEFC Motor 6" Wide Conveyor with Rough-top Belting Tilting Feed Belt to 8 degrees Note: Manual Adjustment, No Indicator 240/480 volt/3phase/60 Hz Hydraulic Feed System with 10 Gallon Reservoir Flow Control Valve for Variable Feed Speed Filter & Shut Off Valve Idler ...more
Baker #ABX, Horizontal Re-Saw, 2019
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Baker
Model: ABX
Year: 2019
- Number of heads: 1, - Guides: Baker Low-Profile Flat Guides with hardened tool steel guide plates with rear backup roller guide wheels, - Dust Output: 6"x6" (15.24cm x 15.24cm) square outlet with a 90° adapter chute with a 4" (10.2 cm) diameter outlet, which can be rotated to serve four directions of discharge. ...more
Baker #ABX, Single Head Resaw, 12" x 12", 30 HP, TEFC, NEMA 12 panel, 95 FPM, New
RT Machine | Hughesville, PA
Category: Resaw Band Saws
Seller: RT Machine
Location: Hughesville, PA
Mfr: Baker
Model: ABX
Baker Model ABX Single Head Resaw Capacity 12" x 12" 28" Precision Machined Band Wheels 30HP Totally Enclosed Fan Cooled Motor Complete Hydraulic Feed System with a 10 Gallon Reservoir, Flow Control Valve for Variable Feed Speed,Filter,& Remote Feed Shut Off Powered Infeed Hold Down NEMA 12 Electrical Panel with ...more
Get email updates for newly added Resaw Band Saws
Resaw bandsaws are built for precise, efficient resizing of wood boards, ideal for lumber production and woodworking. They include single- and multi-head models for customized cuts, allowing quick board thinning and sectioning. Many feature adjustable feed rates, hydraulic controls, and blade tensioning, ensuring consistent, high-quality cuts across various timber sizes.
Baker #ABX, single-head horizontal resaw, 12" x12" capacity, .035" x 1" x 14' 2" blade, 2025, new
Ex-Factory | Charlotte, NC
Category: Resaw Band Saws
Seller: Ex-Factory
Location: Charlotte, NC
Mfr: Baker
Model: ABX
Year: 2026
BAKER ABX Single-head Horizontal Resaw The Baker "ABX" Band Resaws are designed to save space but give you the same great s of larger band resaws.: -- 12" x 12" Cut cap.; 28" precision machined wheels and 30 HP TEFC motor for main drive (40 HP optional); 2 HP hydraulic feed system with a 10-gallon reservoir, flow ...more
Baker #ABXX, Band Resaw, 12" H x 16" width timber, 95 FPM, 40 HP, 28" diameter band wheel, 14'-10" x 1" x 0.035" saw blade, 2026, new
Ex-Factory | Charlotte, NC
Category: Resaw Band Saws
Seller: Ex-Factory
Location: Charlotte, NC
Mfr: Baker
Model: ABXX
Year: 2026
BAKER ABXX Single-Head Resaw, 12" x 16" Cut Cap: Single-Head Band Resaw can be used to cut boards, cants, or reclaim slabs, This Resaw can process a Timber up to 12" H x 16 W" in any desired length. Hydraulic variable speed from 0 - 95 FPM. -- This Model "ABXX" Resaw covers a large range of applications from small to ...more
Baker #ABXX, Single Head Resaw, 16" x 12", 40 HP, NEMA 12 panel, 95 FPM, pedestal, New
RT Machine | Hughesville, PA
Category: Resaw Band Saws
Seller: RT Machine
Location: Hughesville, PA
Mfr: Baker
Model: ABXX
Baker Model ABXX Single Head Resaw, 3PH Accepts Material 16" wide by 12" high 28" Precision Machined Band Wheels 40hp Totally Enclosed Fan Cooled Motor Complete Hydraulic Feed System with a 10 Gallon Reservoir Flow Control Valve for Variable Feed Speed, Filter, & Remote Feed Shut Off Powered Infeed Hold Down Nema ...more
Baker #AX, Single Head Resaw, 12" x 12", 120 FPM, 30 HP, TEFC, New
RT Machine | Hughesville, PA
Category: Resaw Band Saws
Seller: RT Machine
Location: Hughesville, PA
Mfr: Baker
Model: AX
Baker Model AX Single Head Resaw 30-HP TEFC electric motor standard 12" wide hydraulically-power driven conveyor with roughtop belting 28" diameter, CNC-machined, dynamically-balanced, solid, all-steel band wheels 14'-2"x1"x0.035" or 14'-2"x1"x0.035" hardback band blades Baker's Exclusive Low-Profile Flat ...more
Baker #B2 Head Resaw, Diesel, Electric Start
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Baker
Model: B2
Baker Model B 2 Head Resaw, Diesel, Electric Start.
Baker #BBR-0, Band Resaw With Return Conveyor
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Baker
Model: BBR-0
Baker Band Resaw BBR-O, Return Conveyor, Per the seller: The machine is in working order, it had a recent overhaul. We replaced the guide blocks, hold over wheels, and upgraded the wheels to support blades up to 2" wide. It is not currently connected, and is available for inspection., Wired for 240V, The return ...more
Baker #BBR-0, Single Head Resaw, 20 HP, w/ hydraulic belt return, 1994
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Baker
Model: BBR-0
Year: 1994
1994 Baker BBR-0 Single Head Resaw, Hydraulic Belt Return, 20hp Motor.
Baker #BBR-O, Single Head Resaw, 12" capacity, 25 HP, 460 V., 1993
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Baker
Model: BBR-O
Year: 1993
12" capacity, 25HP motor, 460 volt 3-phase.
Baker #BPQ-0, Horizontal Resaw, Good Working Condition
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Baker
Model: BPQ-0
Baker PAQ Resaw, Good Working Condition.
Baker #BX, 2-Head Resaw Band Saw, 12" x 12" cut capacity, 30 HP, 28" diameter band wheel, 120 FPM, 12" width, 14'-2" x 1-1/2" x 0.035" blade (not included), 2026, new
Ex-Factory | Charlotte, NC
Category: Resaw Band Saws
Seller: Ex-Factory
Location: Charlotte, NC
Mfr: Baker
Model: BX
Year: 2026
BAKER BX 2-Head Resaw w/12" x 12" Cut Cap. : -- 30 HP TEFC motor, hydraulically driven feed from head motor, 28"; dia. CNC-machined, dynamically balanced, all-steel bandwheels; variable feed speed from 20 - 120 FPM, feed works with 12" wide rough top belt conveyor on self-centering rollers, and holddown wheel. -- ...more
Baker #C, Single Head Resaw, 240V 3ph, 2021
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Baker
Model: C
Year: 2021
Baker Model C Resaw, 240V 3ph, Baker Cant Turnaround Included, Good Running Condition.
Baker #C, Five Head Resaw, 20 HP, TEFC, NEMA panel, New
RT Machine | Hughesville, PA
Category: Resaw Band Saws
Seller: RT Machine
Location: Hughesville, PA
Mfr: Baker
Model: C
Baker Five Head "C" Model Band Resaw Increase production and profits, while also reducing operating cost with the world famous Baker Muiti-Head Band Resaws. 40:1 Manual Head Raise & Lower System 28" Precision Machined Band Wheels 20HP Totally Enclosed Fan Cooled Motors 7.5HP Stand Alone Hydraulic System with the ...more
Baker #C-2-Head, multi-head resaw, 2022 (2 available)
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Baker
Model: C-2-HEAD
Year: 2022
Baker Model C 2-Head Resaw (Two machines available!), Never put into production!.
Baker #C-4-Head, Multi-head Resaw, 6" width x 12" H capacity, 12" width, 13'-2" x 1-1/4" x 0.035" blade, 28" diameter band wheel, (4) 20 HP, 120 FPM, 2026, new
Ex-Factory | Charlotte, NC
Category: Resaw Band Saws
Seller: Ex-Factory
Location: Charlotte, NC
Mfr: Baker
Model: C-4-HEAD
Year: 2026
BAKER C 4-HEAD Horizontal Resaw w/Powered Return6" Wide x 12" high cap. Resaw; standard spring blade tensioning system;: -- 13'-2" x 1-1/4" x 0.035 blade provides thin kerf savings; quick & easy blade height adjustments. -- Wheels: 28" Dia. CNC machined, dynamically balanced, all-steel band wheels, (4) bolt ...more
JUST ADDED!
Baker #CX, 2-head 12" Horizontal Resaw, 30 HP, 120 FOM, 2018
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Baker
Model: CX
Year: 2018
12@x12” Capacity, 30 HP Motors, 20-120 FOM hydraulic feed.
Baker #CX, Horizozntal Band Resaw, 12" H x 12" width, 120 FPM, 30 HP, 28" diameter band wheel, 14'-2" x 1" x 0.035" blade, 2026, new
Ex-Factory | Charlotte, NC
Category: Resaw Band Saws
Seller: Ex-Factory
Location: Charlotte, NC
Mfr: Baker
Model: CX
Year: 2026
BAKER CX Resaw & s: -- Single-Head Band Resaw can be used to cut boards, cants, or reclaim slabs. Can process a Timber up to 12" H x 12 W" in any desired length. Hydraulic variable speed from 0 - 120 FPM. -- Covers a large range of applications from small to large facilities, they are simple to operate and ...more
Baker #CX, Resaw w/Return, 5-head, 30 HP, unscrambler, transfer conveyor, 2024
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Baker
Model: CX
Year: 2024
2024 Baker 5-Head "CX" Resaw, 30 HP Motors, Hydraulic infeed with return conveyors, Blade Drip System, Infeed Turnaround with live head, 24" x 26' Flattop transfer conveyor, Baker 2 strand Automated unscrambler with drive and controls.
Baker #PAQ, Single Head Band Resaw, 20 HP, TEFC, NEMA 12 enclosure, 1" x 13' 2" x 0.035" blade, 28" wheels, New
RT Machine | Hughesville, PA
Category: Resaw Band Saws
Seller: RT Machine
Location: Hughesville, PA
Mfr: Baker
Model: PAQ
Baker Model P.A.Q. Single Head Band Resaw Baker single cut "PAQ" band resaw with return, electric complete with a totally enclosed fan cooled 20HP motor, Nema 12 enclosure, starter, motor overload protection and all is prewired. Machine also complete with a variable speed hydraulic feed system including the pump ...more
Baker #PAQ-II, Band Re-saw, 2-Head, 8" x 12" capacity, (2) 20 HP, 2026, new
Ex-Factory | Charlotte, NC
Category: Resaw Band Saws
Seller: Ex-Factory
Location: Charlotte, NC
Mfr: Baker
Model: PAQ-II
Year: 2026
BAKER PAQ II Band Re-Saw. -- 2-Head Re-Saw, 8" x 12" cap., (2) 20 HP motors. -- : BAKER Octaguide System, moveable sawheads, stationary conveyor belt, rough top belting and infeed hold down wheel. -- (2) Main drive 20 HP motors. -- Options available at extra charge: Powered hold-down, BAKER Quik-Sharp band blade ...more
Baker 2-Head Resaw, 20 HP motor, return conveyor
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Baker
Baker 2-Head Resaw, 20 HP Motors, Return Conveyor.
Brewco #1600, Single Head Resaw With Run Around
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Brewco
Model: 1600
Brewco 1600, Single Head, Run Around.
Brewco 4-head Resaw
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Brewco
Model: 4-HEAD RESAW
Brewco 4-Head Resaw, Seller has a hydraulic unit to go with the machine., No controls., Optional: System can be cleaned up and controls added, PER SELLER:, this machine is able to pass 7.75" cants, it was purchased in Nelson BC 20 years ago, it has not run since, it is ready to go but has only on off switches and no ...more
Brewco #B1600-Grade, Complete Resaw System, 16" x 16" x 16' capacity, board separator, 2014
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Brewco
Model: B1600-GRADE
Year: 2014
Brewco B1600 Grade Resaw, Complete run-around system, 16"x16"x16' Capacity, Board separator, System has been dismantled and is ready to ship.
Brewco #BBBH, Resaw Band Saw, 20/5 HP, 8" diameter wheels, 6" wide x 8" high capacity, 21" to 72" length, 3' 2" x 1-14" x 0.035 band
Ex-Factory | Charlotte, NC
Category: Resaw Band Saws
Seller: Ex-Factory
Location: Charlotte, NC
Mfr: Brewco
Model: BBBH
BREWCO - BBBH,.6-Head Horizontal ResawComplete with the following s & : -- Working Dimensions: 6" Wide x 8" high capacity and length 21" to 72". -- Band: 13'-2" x 1-1/4" x 0.035 Blade provides thin kerf savings; Quick & easy blade height adjustments. -- Wheel diameter: 28" Dia.; CNC machined; dynamically ...more
Brewco #Wolf-400, Resaw
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Brewco
Model: WOLF-400
This system is no longer needed at the current facility. Ready for immediate removal!, - Brewco Wolf Resaw, - 4" Blade; 20'4" Long, - 40" Bandwheels, - 40 HP Main Motor, - 10 HP Hydraulic Feed, - McDonough Style Guides, - Some spare blades, - Head moves up/down, not the bed, - Approximate dimensions: 9'L x ...more
Brewer #BR-3B8X12R, 3-Head Resaw
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Brewer
Model: BR-3B8X12R
Brewer 3-Head Resaw, Model # BR-3B8X12R.
Brewer #Diamond Brewer 2-HD, 2-Head Golden Eagle Resaw, 2" Blade, 480V., 1997
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Brewer
Model: DIAMOND
Year: 1997
Brewer 2-Head Resaw, Model: Diamond Eagle 2-HD, Blade Size: 2", Year: 1997, Voltage: 480V 3ph, Material Capacity: 15" width, Serial #: 3478, Condition: Fully operational, no rust, Updated electrical panel., Spare Parts: 2" Blades, Dimensions: 30" long x 12' wide, New Bearing on one of the wheels., has 1 New Motor.
Brewer #Diamond Brewer 2000, 3-Head Golden Eagle Resaw, 2" Blade, 480V., 1998
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Brewer
Model: DIAMOND
Year: 1998
Brewer 3 Head Resaw, Model: Golden Eagle 2000, Year: 1998, Blade Size: 2", Voltage: 480 3ph, Material Capacity: 7.5" - 12" width, Serial #: No Placard, Condition: Fully Functional, no rust, Updated electrical panel., Spare Parts: 2" Blades, Dimensions: 20' long x 11' wide, New Bearing on all wheels front and ...more
Brewer #GE-2000-3B, 3-head horizontal resaw, 8" W x 12" H capacity, 20-100 FPM, 1998
Ex-Factory | Charlotte, NC
Category: Resaw Band Saws
Seller: Ex-Factory
Location: Charlotte, NC
Mfr: Brewer
Model: GE-2000-3B
Year: 1998
BREWER - GE 2000-3B: 3-Head Horizontal Resaw -- Cant capacity: 8" W x 12" H x Random length; Saw kerf: 0.083". -- Blade wheel size: 36" Diameter x 2" W; blade length: 198", blade width: 1"; 1-1/4";; 1-1/2"; or 2". -- Hydraulic variable feed speeds: 20 to 100 FPM.: -- (3) 20 HP Saw head motors; rough-top feed belt. -- ...more
Brewer #Golden-Eagle, single Head Resaw, 12" x 12" throat, 2000
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Brewer
Model: GOLDEN-EAGLE
Year: 2000
2000 Brewer Golden Eagle Single Head Resaw, Return, 12x12 Throat Opening.
JUST ADDED!
Brewer #Golden-Eagle-2000, 5-Head Resaw, 2015
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Brewer
Model: GOLDEN-EAGLE-2000
Year: 2015
Brewer 5-Head Resaw, Unit has been service., Bandwheels have been resurfaced., Machinery is disconnected and ready to ship., Frame: Heavy 5/8" plate and 4" X 4" tubing is used for, reinforcing to avoid the bending action found in, lighter weight band saws., Arbor & bearings: (2) bearing design (no car hubs) 2 ...more
Brewer, 5-Head Resaw with Return, return belt
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Brewer
Brewer 5-Head Resaw, Return Belt.
Brewer, 3-head Resaw, with spare re-crowned band wheels
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Brewer
Brewer 3-Head Resaw, (2) 20 HP motors and (1) 30 HP motor, 1-Spare set of re-crowned band wheels.
Cam-Wood #BX-1212-HR-TNX, Horizozntal Band Resaw, 12" H x 12" width, 90 FPM, 20 HP saw, 28" x 2" band wheel, 201" x 3" blade, 2026, new
Ex-Factory | Charlotte, NC
Category: Resaw Band Saws
Seller: Ex-Factory
Location: Charlotte, NC
Mfr: Cam-Wood
Model: BX-1212-HR-TNX
Year: 2026
CAM-WOOD BX-1212-HR-TNX Two-Head Band Resaw Can be used to cut boards, cants, or reclaim slabs; max. working height up to 12" H under pressure roller x 12" W; 1/4" - 10-5/8" between blade and conveyor; VFD controlled variable speed from 0 - 90 FPM.: -- 20 HP Saw Motor, 28" x 2" dynamically balanced cast iron band ...more
Cam-Wood #BX-1212BEEX, Horizozntal Band Resaw, 12" H x 12" width, 80 FPM, 20 HP saw, 28" x 1" band wheel, 168" x 1" blade (not included), 2026, new
Ex-Factory | Charlotte, NC
Category: Resaw Band Saws
Seller: Ex-Factory
Location: Charlotte, NC
Mfr: Cam-Wood
Model: BX-1212BEEX
Year: 2026
CAM-WOOD BX-1212BEEX Single Bottom Head Band Resaw.Can be used to cut boards, cants, or reclaim slabs; : -- Can process up to 12" H x 12" W; 5/16" - 5-1/4" from blade to conveyor. -- 2 HP Electric motor controlled variable speed from 12 - 80 FPM. -- This Model BX-1212BEE is : -- 20 HP Saw Motor, 28" x 1" band wheels ...more
Cam-Wood #BX-1212HR-1X, Horizozntal Band Resaw, 12" H x 12" width, 60 FPM, 20 HP saw, 24" x 2" band wheel, 184" x 1.5" blade (not included), 2026, new
Ex-Factory | Charlotte, NC
Category: Resaw Band Saws
Seller: Ex-Factory
Location: Charlotte, NC
Mfr: Cam-Wood
Model: BX-1212HR-1X
Year: 2026
CAM-WOOD BX-1212HR-1 Single-Head Band Resaw w/30 Bevel CuttingCan be used to cut boards, cants, or reclaim slabs; : -- Max. working height up to 12" H under pressure roller x 12" W; 1/4" - 10-5/8" between blade and conveyor; -- VFD controlled variable speed from 0 - 60 FPM. : -- 20 HP Saw Motor, 24" x 2" dynamically ...more
Cam-Wood #BX-1616-HR-TNX, Horizozntal Band Resaw, 16" H x 16" width, 90 FPM, 30 HP, 28" x 2" band wheel, 201" x 3" blade (not included), 2026, new
Ex-Factory | Charlotte, NC
Category: Resaw Band Saws
Seller: Ex-Factory
Location: Charlotte, NC
Mfr: Cam-Wood
Model: BX-1616-HR-TNX
Year: 2026
CAM-WOOD BX-1616HR-TN Two-Head Band Resaw Can be used to cut boards, cants, or reclaim slabs; max. working height up to 16" H under pressure roller x 16" W; 1/4" - 12" between blade and conveyor; VFD controlled variable speed from 0 - 90 FPM.: -- 30 HP Saw Motor (each head), 28" x 2" dynamically balanced cast iron ...more
Cam-Wood #BX-2410HRX, Horizozntal Band Resaw, 10" H x 24" width, 82 FPM, 30 HP, 28" x 2" band wheel, 195-1/2" x 2-1/8" x 3/64" blade (not included), 2026, new
Ex-Factory | Charlotte, NC
Category: Resaw Band Saws
Seller: Ex-Factory
Location: Charlotte, NC
Mfr: Cam-Wood
Model: BX-2410HRX
Year: 2026
CAM-WOOD BX-2410HR Single-Head Band Resaw w/30 Bevel CuttingCan be used to cut boards, cants, or reclaim slabs; max. working height up to 10" H under pressure roller x 24" W; 5/32" - 10" between blade and conveyor; VFD controlled variable speed from 0 - 82 FPM.: -- 30 HP Saw Motor, 28" x 2" dynamically balanced cast ...more
Cantek #HB-800, Band Resaw, 32" wheel diameter, 20 HP, 3.543" Wheel H, 30-5/8" throat, 15-3/8" underguide capacity, 4" width x 217" L blade, 5024 SEPM, 2026, new
Ex-Factory | Charlotte, NC
Category: Resaw Band Saws
Seller: Ex-Factory
Location: Charlotte, NC
Mfr: Cantek
Model: HB-800
Year: 2026
CANTEK HB-800 32" Vertical Band Resaw32" Wheel diameter, 20 HP motor Vertical Band Saw;: -- 3.543" (90 mm) wheel width, 30-5/8" throat capacity, 15-3/8" under guide capacity. -- 4" Blade width X 216- 217-1/8" blade length. -- 20 HP main motor, generates a blade speed of 5,024 SFPM.s: -- Heavy fabricated steel machine ...more
Danckaert #44, Vertical Band Resaw, 44" x 5" Bandsaw, 14" cut, 60 & 100 HP, 24' lumber length
Ex-Factory | Charlotte, NC
Category: Resaw Band Saws
Seller: Ex-Factory
Location: Charlotte, NC
Mfr: Danckaert
Model: 44
DANCKAERT - 44,.ResawAir Strain 44"; x 5"; Bandsaw.s & : -- McDONOUGH Center Split Feed Works. -- Wheel is supported on both sides - not cantilevered. -- Pressured guides. -- McDONOUGH Infeed Rolls. -- Max. Cut: 14";. -- New Dynamic brake. -- 60 & 100 HP. -- Control Cabinet (has battery backup and resistors to ...more
Go Fast 5-Head Resaw
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Go Fast
Go Fast 5-Head Resaw, Unit was cut into two pieces and can be put back together with a weld in the middle., Approx layout is 31' x 8'.
Go Fast Resaw 6 x 12, minimal use, 2023
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Go Fast
Year: 2023
2023 Go Fast 6x12 Resaw, Has minimal use.
Go Fast 2-Head Resaw with deduster, 10 HP
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Go Fast
GoFast 2-Head Resaw, 10 HP main motors, Go Fast Board Deduster.
Go Fast Single Head Resaw, 15 HP Motor, 2023
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Go Fast
Year: 2023
Go Fast Resaw, 15 HP Motor, Put under power to test, never put into production.
Grizzly #G0504, 16" Horizontal Resaw w/ Return Conveyor, 7300 RPM, 180" x 1" blade, 61 FPM
Carolina Machinery Sales | Monroe, NC
Category: Resaw Band Saws
Seller: Carolina Machinery Sales
Location: Monroe, NC
Mfr: Grizzly
Model: G0504
Grizzly G0504 Horizontal Resaw With Return Conveyor, please see pictures for full sheet.
