For Sale by Aucto

Surplus Record Dealer Since 2022
Location: Lake Zurich, IL
Contact Trevor Jenson
Phone Number: 844...> Show Phone Number 844-605-1425
Let the seller know you found their listing on Surplus Record!
$5,500 USD
Description
This used 2.5 in NRM Pacemaker III extruder is air cooled and non-vented, with 4 barrel zones, 3 downstream zones and a 42 in centerline. It is driven by a 75 HP Baldor Reliance DC motor, frame MC2812ATZ, rated 1750/2100 RPM, 500 volt, 127A, stab shunt, and includes a 1/2 HP blower. The drive is a 90 HP Control Techniques Mentor MP DC drive, model MP155A4, 500 VDC, with 155A continuous DC output current, 232.5A DC output current at 150% overload and 139A continuous AC input current, 480 volt class. Controls and instruments include Eurotherm 3216 and Omron E5CN temperature controllers, a CAL 9900 melt temperature controller, a Gentran G434 melt pressure indicator, an analog DC amp gauge, a Simpson digital RPM readout, start/stop, E-stop and a speed pot. A 400 amp main disconnect and a manual swing bolt die clamp assembly are included. Approximate dimensions are 106 in by 60 in by 95 in high. The extruder is in fair condition. Contact us for more information or to arrange an inspection.
Inquire Further with Aucto!
Buyers Who Viewed This Listing Also Viewed:
JUST ADDED!
4.5" NRM #PACEMAKER-III, Single Screw Extruder, 34:1 L/D, 12' vented barrel, 8" feed throat, 200 HP DC motor, 500 V., SCR controls, 1982, AS IS
Category: Extruders and Extrusion Lines
Seller: Aaron Equipment Co
Location: Schaumburg, IL
Mfr: Nrm
Model: PACEMAKER-III
Year: 1982
used nrm pacemaker iii 4.5" single-screw extruder with 34:1 l/d ratio. unit s a 12' long vented barrel with electric heating and water cooling, along with an 8" round feed throat. screw is driven by a 200 hp, 500 vdc electric motor. barrel includes a 5.5" side vent located approximately 6.5' from the feed ...more
JUST ADDED!
2.5" HPM #2.5TMC-24, extruder, 24:1 L/D, air cooled, 4 barrel zones, 40 HP DC, 13.95:1 Koellmann gearbox, 42" centerline, 460 V., 1994
Category: Extruders and Extrusion Lines
Seller: Aucto
Location: Lake Zurich, IL
Mfr: Hpm
Model: 2.5TMC-24
Year: 1994
This 2.5" HPM 2.5TMC-24 extruder has a 24:1 L/D ratio, is air cooled and has 4 barrel zones and 3 downstream zones. The centerline is 42". It is driven by a 40 HP Powertec DC brushless motor, frame 259TZ, rated 2500 RPM, 640 bus VDC and 234 peak RMS amps, through a Koellmann gearbox rated for 108 HP with a 13.95:1 ...more
JUST ADDED!
2.5" Davis Standard, extruder screw, 24:1 L/D, Mark IV shank, barrier flights, spiral Maddock mixer, 73-3/8" OAL
Category: Extruders and Extrusion Lines
Seller: Arlington Machinery
Location: Lake Zurich, IL
Mfr: Davis Standard
Used 2.5" Davis Standard Screw 24: 1 L/D 73 3/8" Approximate Overall Length 6 1/4" Approximate Shank Length Davis Standard Mark IV Shank Barrier Flights Spiral Maddock Mixer Approximate Dimensions: 73 3/8" x 2.5" Diameter.
JUST ADDED!
2.5" Twin Screw Compounding Line, 64mm, Maguire 6-component blender, underwater cutting system, in-line desiccant dryer
Category: Extruders and Extrusion Lines
Seller: Plastic Machinery Of New York Inc
Location: Yaphank, NY
Complete FULL Compounding Line 64mm Twin Screw, Complete FULL Compounding Line 64mm Twin Screw, 6 Multi-component Maguire Blender, 64 mm Twin Screw Extruder, under water cutting system, & In-Line Desiccant Dryer.
2.5" Welex #2.5-24:1-RHNV, single screw extruder, 24:1 L/D, 40 HP DC, air cooled barrel, 3 heating zones, hydraulic screen changer, SCR drive, 1992
Category: Extruders and Extrusion Lines
Seller: Revelation Machinery
Location: Chicago, IL
Mfr: Welex
Model: 2.5 24:1 RHNV
Year: 1992
Make: Welex, Model: 2.5 24:1 RHNV, Year: 1992, Machine Location: California, Screw Diameter: 2.5″, Length-to-Diameter Ratio: 24:1, Motor Power: 40 HP DC Motor, Gearbox Ratio: 9.38:1, Barrel Cooling: Air Cooled, Heating Zones: 3, Barrel Type: Jacketed With Electrical Heaters, Screen Changer: Hydraulic ...more


























