Results for Single Screw Extruder

Make: Crown, Model: 2.5" Single Screw Extruder, Year: 2015, Machine Location: Upon Request, Expected Rate: 10-200 Kgs/hr., Extruder : 2.5" Dia., 36:1 L/D Ratio, Barrel Centerline: 40″, Horsepower: 75HP, Drive: AC, Screw RPM: 140, Max PSI: 10,000, # of Barrel Zones: 5, Cooling: Closed Loop Cooling System ...more

Product s, Used 1.0" Killion Extruder, 24:1 L/D, 3 HP DC Motor, 24:1 L/D Ratio, Air-Cooled Barrel, 17: Approximate Gearbox Ratio, 3 Barrel Zones, 1 Die Zone, Eurotherm Temperature Controllers, 3 HP GE DC Motor With Control Techniques Drive, 3 HP DC Motor And DC Drive, 42" Centerline, Includes Screw, S/N N5222 ...more

Make: American Kuhne, Model: AK 120MM 30:1 Rebuild, Year: 2013, Machine Location: Alabama, -Screw Size: 120 mm, -L/D Ratio: 30:1, -Motor: 200 HP, -Digital Controls, -42″ Centerline Height, -Electrically Heated, -Air Cooled Barrel, -Electrical Requirements: 480 V.

Used 1.25" Davis Standard Single-Screw Extruder, 24:1 L/D, Manufacturer: Davis Standard, Model: DS-12H, Serial: L2978, Year: 1990, Barrel: non-vented, 3- zone, electrically heated, air cooled, 42" centerline height, Belt driven by a 5 hp DC motor, 230 volt, Gearbox: rates 20 hp, 1.25 service factor, 100 rpm max. screw ...more

Used 1.5" Killion single stage 24:1 L/D extruder screw., Location: On Site at Perry (Hainesport, NJ - USA).

Used 0.375" Randcastle Microtruder extruder, model RCP-0375,.375" diameter singled screw, 24:1 l/d, electrically heated, air cooled barrel, jacketed feed section,.75 hp, 230 volt motor, 15:1 gearbox ratio, control panel with (3) barrel, (1) adaptor, (1) die zones and motor vfd controller, serial# J1935, built ...more

Used 0.375" Randcastle Microtruder extruder, model RCP-0375,.375" diameter singled screw, 24:1 l/d, electrically heated, air cooled barrel, jacketed feed section,.75 hp, 240 volt motor, 15:1 gearbox ratio, control panel with (3) barrel, (1) adaptor, (1) die zones and motor vfd controller, serial# J3431.

Bonnot single screw extruder. 2-1/2" diameter by 40" long screw (16: 1 L to D), four 10" barrel segments with individual jackets for heating or cooling (temperature range up to 550°F) and 20 HP variable speed drive. Rates dependent on materials, application and machine configuration., OAD: 87" ...more

Used Bonnot single screw extruder, model 2", stainless steel barrel and screw, with approximately 2" diameter X 10" long jacketed barrel with Pin and Grooving barrel, 6" x 4.5" feed throat with stainless steel chopper bar, driven by 3 hp, 230/460 volt motor through gearbox, serial# 2091, built 1970.

Used 1.5" Killion single stage 24:1 L/D extruder screw., Location: On Site at Perry (Hainesport, NJ - USA).

Used HPM / Gala underwater pelletizing line consisting of the follow: 2.5" HPM single screw extruder, model TM25 III-38, 38:1 l/d ratio, electrically heated, water cooled barrel, vented, Lufkin gearbox, 17.71:1 gearbox ratio, driven by 75 hp dc motor, serial# 78-333, with Gala underwater pelletizer with water box ...more

(2) Carbon steel Screws for screw conveyor, screws only. Available: 24" diameter x 13'4" and 24" diameter x 19'4" sections. Units have 6-1/2" diameter center shaft, approx. 1/2" thick heavy duty flites, with 21-3/4" spacing between flights. Shafts are set for 4" diameter stub shafts. Units last run in mining ...more

, used 7" wide X 25'6" Lgth Screw conveyor. Has stainless Steel Trough and carbon steel screw. Inlet is 2' x 8" wide. 7" outlet. 1.5 HP, 1690/1710 rpm, 208-230/460 volt motor into gear reducer with 124:1 ratio. Approx 14 RPM output.,., Type. SCREW.

, used 7" wide X 4'10" Lgth Screw conveyor. Has stainless Steel Trough and carbon steel screw. 6" outlet. 1 HP, 1750, 230/460 volt motor into gear reducer.,., Type. SCREW.

Carbon steel screw conveyor, measures 10" diameter X 16'6" Long Screw Conveyor. Includes carbon steel U-shaped trough with 10" diameter x 16'6" long mild steel screw. Open top. Less motor and drive assembly. Last used in saw dust application., Measurements: 10" Diameter X 16'6" Long, Materials of ...more

Screw conveyor, 6" diameter x 5' long, incline type for operation at 45 degree angle. Unit designed to run inclined on 45 degree angle with 12" x 12" hopper feed, 4" x 4" discharge. Unit has carbon steel contact parts and is in good condition, close tube type, less end plate, less drive., Type: Tubular Conveyor ...more

Stainless steel screw conveyor, screw measures 9-1/2" diameter x 5'9" long, 10" wide stainless steel trough. Includes 10" diameter in/out. Driven by 1.5 HP, 230/460V, 1720 RPM, 3/60Hz motor thru gearbox with manual speed control. Drive end is mounted on mild steel stand with legs. Previously used at spice ...more

Stainless steel screw conveyor, screw measures 6" diameter X 10' long, with standard screw pitch, 7" wide stainless steel trough. Screw includes gearhead motor rated for 1725 RPM, 208-230/460V, 3/60Hz motor, thru gear reducer. Last used at dried fruit processing facility., HP: 0.75 HP (Estimate), Type: Stainless ...more

twin screw 36" hollow screw auger conveyor, 6ft wide screw conveyor, dual 36 inch screw conveyor, double 36" x 27ft hollow screw conveyor, Dual 36" shaftless hollow screw auger conveyor, inside length 27 feet 6 inches, inside width 6 feet 2 inches, overall outside length of conveyor 30ft 10 inches, conveyor ...more

Used Spaans screw conveyor, approximately 24" wide x 216" long trough, with 15" pitched screw conveyor, driven by 5 hp, 230/460 volt motor, 24" x 24" bottom end discharge, outboard roller bearings, packing glad seals, 277" overall length, serial# 1986F.

Used Spaans screw conveyor, approximately 24" wide x 785" long trough, with 15" pitched screw conveyor, driven by 20 hp, 230/460 volt motor, end discharge, outboard roller bearings, packing glad seals, serial# 1986C1.

Used 10" Twin screw feeder, stainless steel construction, with (2) 5" diameter x 102" long inter-meshing co-rotating screws, 10" wide trough, 1.5" screw pitch, 6" x 9" feed opening, 3" outlet, (8) side injection ports, hinged top cover, mounted on stainless steel frame, driven by 7.5 ...more

One (1) used 3" diameter Flexible Screw Conveyor Stainless steel flexible screw and tube Flexible screw is 3" diameter x 12' 9" long Tube is 4.5" OD 1" flat flights 5 HP gear reduced drive, 3 phase, 208-230/460 voltage Feed hopper is 18.5" x 24.5" - stainless steel and flanged ...more

Used 10" dia. X 17'L Tubular Screw Conveyor, Overall dimensions: 18'-4" L x 26" W x 24" H., Weight = 790 LBS.

shaftless screw conveyor, shaftless spiral conveyor, shaftless tapered screw auger, used shaftless screw conveyors, hollow screw conveyor, used spiral screw auger conveyor., shaftless spiral conveyor inside length 14ft 9 inches overall outside length 16 ½ ft+-, trough width 10 ¼ inch ID. outside width ...more

Flexible screw conveyor, stainless steel, 4" diameter, includes (2) 4" diameter tubes, 12' & 15' long and (2) screws - 3.875" diameter x 12'8" long and 3.687" diameter x 17'10" long. Unit is offered with carbon steel hopper measuring 29" x 29" x 30" deep to 60-degree cone bottom. Screw is driven by ...more

Used 12" Dia. x 34' Long Industrial Screw Conveyor, Auger: Carbon steel with standard pitch flighting, 1/8" thick., Trough: Stainless steel, three-section flanged U-trough with twin drop-outs, hanger bearings at connections., Multiple belly patches on trough using continuous fillets welds., Discharges: ...more

Used 16" Dia. X 16' L Stainless Steel Screw Conveyor, Stainless steel, two-section U-trough with cover., Diameter: 16 inches, Pitch: 16 inches, Trough Length: 16'-0", Flanged Discharge: 17" square, 3HP gearmotor/chain drive (230/460V, 60Hz, 3ph.), Weight = 1,310 LBS.

Used 6" Dia. X 7'L Stainless Steel Screw Conveyor, Stainless steel U-trough with 48" length of cover and extended height., Auger Diameter: 6" with standard pitch, light duty flighting, Trough Length: 7'-6 1/2", Flanged Discharge: 7" square, 1HP gearmotor & chain drive (230/460V, 60Hz ...more

Make: NA, Model: 10AC, Year: 1900, Machine Location: New Jersey, Total Length: 10', Auger Screw: 13" blade to blade gap.

Product s, 40" Brown model B4042 thermoforming line with, B4042 former and T340 trim press. New 1996, Brown model B4042 in line thermoformer with 3 roll cooling rolls., 40 x 42" Brown servo thermoformer with upgraded servo drives., Max daylight of 6" up and down., 40" wide Brown model T340 trim press with canopy servo ...more

Product s, 40mm Kiefel Lowboy Extruder, 26:1 L/D, With Die,Rotating Cart Calibration Cage and Takeoff, Air Cooled Extruder, 3 Barrel Zones, 42 HP AC Vector Drive, Extruder Controlled With Kirion C Automation, 15" Touch Screen Display, Extrduer Comes With BD Plast Manual Screen Changer(New In 2014), 80MM Die With Spare ...more

Used Werner & Pfleiderer twin screw extruder, model ZSK53, 53mm twin screws, co-rotating, 40:1 L/D, electrically heated, water cooled barrel with (7) barrel sections, 60 hp dc motor, thru gear box with 5:1 ratio, approximately 345 rpm screw speed, with control panel and spare screw segments, serial # 227916, work# ...more

Used Zumbach surface fault detector, model KW20, 2.5" wide aperture with 2" wide opening with idler rollers, serial# 2795.1353.

Used Zumbach surface fault detector, model KW20, 2.5" wide aperture with 2" wide opening with idler rollers, serial# 2709.1262.

Used Zumbach surface fault detector, model KW20, 2.5" wide aperture with 2" wide opening with idler rollers, serial# 2506.103.

Used 12" Gloucester Mini separator, 480V, 3 phase.

Used 0.25" Brabender extruder, electrically heated, air cooled barrel, 48:1 L/D, driven by 2 hp, 180 volt motor with VFD, controls on frame.

One (1) Used Werner & Pfleiderer 58mm Twin Screw Extruder, twin screw compounder, continuous mixer, 16:1 L/D, Type Continua 58, Reliance Motor 25HP DC 1750RPM 500V, Gearbox rated for 40HP, co-rotating, 3 heating zones, electrically heated, water cooled, vented, control panel and pump included, previously extruder ...more

107364, One (1) Used Davis Standard Extruder Model MV35IN35SR, L/D BARREL HAVING A SEVEN (7) ZONE ELECTRICALLY HEATED, WATER COOLED (CLOSED LOOP), AND SIDE VENTED BARREL AT A 52" CENTERLINE HEIGHT. GEARBOX HAS A 5.67:1 REDUCTION RATIO AND IS RATED AT 158 HP AT A SERVICE FACTOR OF 1.25. GEARBOX IS BELT DRIVEN BY A 200 ...more

Used 6" Gloucester water ring pelletizing line, with 6" Gloucester extruder, model 266-001, 30:1 L/D, air cooled with Contracool and blower, jacketed feed section, feed hopper, vented barrel, with control panel, machine serial# 266-33392-01, built 1990. Gneub rotary filter screen changer, model SF90, serial# ...more

One (1) Used 10" Farrel Hot Feed Rubber Extruder, roller feed, Motor 200 HP, 500 volt, 1750 rpm.

Stock#: 17744., Davis Standard straw/tubing co-extrusion extrusion package manufactured 10/2012, Last used on three color straws extruding two lanes of straws at one time. Extruders and controls are unitized on a single base. 460/3/60 input power. 278 maximum amp load, A Davis standard model MV35IN35 3.5 24:1 L/D ...more

Product s, Used 72mm Jiangsu Xinda Twin Screw Extruder, Model PSHJ72, 40:1 LD Ratio, 10 Elements, Port in Zone 5, Vent In Zone 8, 110 Kw Main Motor(147.5 Hp) With AC Drive, 500 RPM Screw Speed, Has Clampshell Style Barrel Opening, 11 Temp Zone,1 Die Zone, 1 Pressure Readout 2.2Kw Material Feeder, With Control Panel ...more

, SAW BLADE DIAMETER: 32", HEAD STROKE: 26", LENGTH OF RAILS: 30 APPROX., TYPE DRIVE TO SAW BLADE: BELT, - HYDRAULIC OPERATED HOLDDOWN, - TILT SAW HEAD, - MOTORIZED TRAVEL, MOTOR DRIVE: 50 HP, 230/460/60/3, 1740 RPM - SAW HEAD, 1/2 HP, 208/230/460/60/3, 1725 RPM - TRAVEL, 5 HP, 180/330/50/3, 1425 RPM - HYDRAULIC UNIT ...more

Used 1.5" Killion Single-Screw Extruder, 24:1 L/D, Model: KL-150, Serial: 10628, Includes: (3) control panels, Zenith melt pump with 2 hp motor. Model PEP-10 rated at 3.4-68 lbs/hr spare grooved feed throat, and (2) transformers, miscellaneous parts., Additional information: the Killion extruder was custom designed to ...more

Used 2.36" Gloucester Vented Single-Screw Extruder, 32:1 L/D, Year: 1986, Barrel: 45" centerline height, Driven by a 50 hp DC motor and SCR control, Gearbox: 9.48:1 ratio, serial 140, Additional information: top center feed throat, includes temperature control panel and 5-hole strand die., Location: On Site at Perry ...more

Used 8" Buss Hot Melt Single-Screw Extruder and Pelletizing System, 6:1 L/D, Model: MDS200-4, Serial: 99/410820, Year: 1999, Screw is water heated/cooled, Barrel: 3-zone, oil heated, oil cooled, Direct driven by a 100 hp DC motor, volt, rpm, Includes: Buss Hot Cut Pelletizer Model PVW200 with oil heated/cooled die ...more

Used 8" wide Wayne horizontal cast film extrusion downstream. Package includes (6) rolls total, (3) chrome, (3) rubber. Each roll is rotary union. Includes (2) gearhead motors, operator controls. Serial #9545., Location: On Site at Perry (Hainesport, NJ - USA).