351 - 400 of 508 listings
19 Stand, Ardcor Tooled Decking Line, 2.25" arbor, 42" roll space, 16" horizontal center, 10" vertical center
National Machinery Exchange | Newark, NJ
Category: Rollformers
Seller: National Machinery Exchange
Location: Newark, NJ
Mfr: Ardcor
19 STAND ARDCOR TOOLED DECKING LINE, 42" RS, 2.25" ARBOR, CONSISTING OF:, L-TYPE COIL CAR, 48" X 20,000# UNCOILER, 16"-20" ID, HYDRAULIC WEDGE EXPANSION & OVERARM, ARDCOR ROLL FORMER, ENTRY STRIP GUIDE, # OF STANDS - 19, SHAFT DIAMETER - 2.25", ROLL SPACE - 42", VERT. SHAFT CENTERS - 5" TO 10", HORIZ. SHAFT ...more
19 Stand, Ardcor, 23 stand base, 1.5" shafts, 12" roll space, 4"-5.750" vert, 10" horizontals
Roll Form Solutions Inc | Grand Haven, MI
Category: Rollformers
Seller: Roll Form Solutions Inc
Location: Grand Haven, MI
Mfr: Ardcor
19 Stand, Contour #CR-A-H-3-1/2 rafted rollformer, 24" roll space, 2-1/2"shaft diameter, 2 bases
Yoder Machinery Sales | Holland, OH
Category: Rollformers
Seller: Yoder Machinery Sales
Location: Holland, OH
Mfr: Contour
Model: CR-A-H-3-1/2
SERIAL. 84-048MODEL. CR A-H-3-1/2NUMBER OF STANDS. 19NUMBER OF BASES. 2ROLL SPACE. 24"DIAMETER OF SHAFT. 2-1/2"VERTICAL RANGE. 5-1/2" MIN; 8-1/2" MAXBASE TO CENTERLINE OF LOWER SHAFT. 7-1/2"UPPER ARBOR ADJUSTMENT. 3"HORIZONTAL CENTER DISTANCE. 19"GEARING. RAFTED. 4 X 4 1 X 3U JOINTS. YESCONTROL PANEL. YESCOOLANT BASE. ...more
19 Stand, Dreistern #P-60, side by side dual palss rollformer, 5" roll space, 25mm shaft, rafted
Yoder Machinery Sales | Holland, OH
Category: Rollformers
Seller: Yoder Machinery Sales
Location: Holland, OH
Mfr: Dreistern
Model: P-60
MODEL. P-60-2, NUMBER OF STANDS. 19, DIAMETER SHAFT. 25MM, ROLL SPACE. 5", VERTICAL ADJUSTMENT. 3" TO 4", BASE TOP TO LOWER SPINDLE CENTER. 4-1/2", HORIZONTAL CENTER DISTANCE. 5.5", RAFTED. YES, U JOINT DRIVE. YES, SIDE BY SIDE OPERATION. POSSIBLE, (2) 3-WAY STRAIGHTENING HEADS. YES, MOTOR. 7.5/15HP, CONTROL. E-TRAC ...more
JUST ADDED!
19 Stand, Michigan Rollform #15GMHU-20-L, rollforming line, 20" x 1.5", 3 coil keepers, maual mandrel expansion
D & H Machinery Inc | Toledo, OH
Category: Rollformers
Seller: D & H Machinery Inc
Location: Toledo, OH
Mfr: Michigan
Model: 15GMHU-20-L
19 Stands 20.00" x 1.50" Michigan Rollform Rollforming Line, Model Number: 15GMHU-20-L, Rollformer was Rebuilt by MRF in 2023., Line was only run for 2 months after rebuild., Consisting of the following:, -Uncoiler: New in 2023, 6,000# x 16" Wide Capacity, Non-Powered Pulloff Style Payoff Reel, Manual Mandrel ...more
Get email updates for newly added Rollformers
Rollformers (also known as roll forming machines) are used to shape sheet metal or strips into continuous profiles by passing them through a series of rollers. Commonly used in industries like construction, automotive, and manufacturing, they are ideal for producing parts like roofing panels, beams, and tubing. Rollformers are essential for efficiently creating uniform, high-quality metal profiles in large-scale production.
19 Stand, PBR, panel rollformer, 240 V., 1-phase, never used
Community Steel | Gonzales, LA
Category: Rollformers
Seller: Community Steel
Location: Gonzales, LA
Mfr: Pbr
Year: 2025
Brand new 2025 PBR panel roll forming machine. 19 total stands. Hydraulic controled pre and post shear. 240V single phase machine producing at 70ft/min.
JUST ADDED!
19 Stand, Double decker roll former, PBR-PBU, 480 V., 3-phase, brand new
Community Steel | Gonzales, LA
Category: Rollformers
Seller: Community Steel
Location: community steel, LA
Model: 2026
Brand new double decker roll former machine. does both PBR and PBU panels. 19 on stands on each deck. hydraulic pre and post cut. 480v 3 phase. message for more.
20 Stand, Ardcor #S10-2.5-37, rollformer, 2.5" arbor, 37" roll space, 10" horizontal centers, 4.75"-5.25" horizontal centers, 40 HP
Yoder Brothers Machinery | Toledo, OH
Category: Rollformers
Seller: Yoder Brothers Machinery
Location: Toledo, OH
Mfr: Ardcor
Model: S10-2.5-37
SERIAL. 82-024 MODEL. S10-2.5"-37 NUMBER OF STANDS. 20, ARBOR DIAMETER. 2.5" ROLL SPACE. 37" HORIZONTAL SPACING. 10" BOTTOM SPINDLE TO BASE. 5.75" VERTICAL ADJUSTMENT. 4.75 TO 5.25", SPINDLE GEAR RATIO. 1.333 TO 1, MOTOR. 40 HP.
20 Stand, ASC #20HM-3-1/2, 3.5" shaft diameter, 42" roll space, L to R, 40 HP, entry guide
HCI Machines | Venetia, PA
Category: Rollformers
Seller: HCI Machines
Location: Venetia, PA
Mfr: Asc
Model: 20HM-3-1/2
20 STAND ASC ROLL FORMER : ENTRY GUIDE ELECTRICAL PANEL NO TOOLING.
20 Stand, ASC #20HM-3-1/2, rollformer, 3.5" shaft diameter, 42" roll space, L to R, #14073J
Timco Inc | Columbia, TN
Category: Rollformers
Seller: Timco Inc
Location: Columbia, TN
Mfr: Asc
Model: 20HM-3-1/2
ASC 20 STAND ROLL FORMER, STOCK# 14073J, MODEL NUMBER: 20 HM-3 1/2, S/N: 85431, ROLLSPACE: 40", HORIZONTAL CENTERS: 14", VERTICAL ADJUSTMENT: 6.375" - 8.750", SHAFT DIAMETER: 3.5", LINE DIRECTION: R-L, BASE TOP TO CENTER LOWER SPINDLE: 7.625", MILL BED TO FLOOR 28.5", ENTRY GUIDE, ELECTRICAL PANEL, MOTOR: 40 HP 480 ...more
20 Stand, ASC #20HM-3-1/2, 40" roll space, 14" horizontal centers, 6.375"-8.750" vertical adjustment
D & D Industries Inc | Monclova, OH
Category: Rollformers
Seller: D & D Industries Inc
Location: Monclova, OH
Mfr: Asc
Model: 20HM-3-1/2
ASC 20 STAND ROLL FORMER, MODEL NUMBER: 20 HM-3 1/2, S/N: 85431, ROLLSPACE: 40", HORIZONTAL CENTERS: 14", VERTICAL ADJUSTMENT: 6.375" - 8.750", SHAFT DIAMETER: 3.5", LINE DIRECTION: R-L, BASE TOP TO CENTER LOWER SPINDLE: 7.625", MILL BED TO FLOOR 28.5", ENTRY GUIDE, ELECTRICAL PANEL, MOTOR: 40 HP 480 VAC, EQUAL ...more
20 Stand, RS Contour #CRTM-1.5-20S, rollformer, 1.5" spindle diameter, 10" roll space, 6" horizontal centers, 4" verti adj., 40-120 FPM, AMS MP300
Yoder Brothers Machinery | Toledo, OH
Category: Rollformers
Seller: Yoder Brothers Machinery
Location: Toledo, OH
Mfr: Contour
Model: CRTM-1.5-20S
SERIAL 85-039, MODEL CRTM 1.5 20S, STANDS 20, SPINDLE DIAMETER 1.5", ROLL SPACE 10", HORIZONTAL CENTERS 6", VERTICAL 4", GEARING EQUAL 1:1, SPEED 40 TO 120 FPM, DIRECTION LEFT TO RIGHT, MOTOR 15 HP, CONTROLS AMS MP300.
JUST ADDED!
20 Stand, Dahlstrom #400-20OB, rollformer, 12" roll space, 1.5" arbor diameter, 40 HP, 100 FPM
iGAM | Detroit, MI
Category: Rollformers
Seller: iGAM
Location: Detroit, MI
Mfr: Dahlstrom
Model: 400-20OB
This listing is for a Dahlstrom 400-20OB Rollformer., Manufacturer: Dahlstrom, Model: 400-20 OB, Serial: 1278, Stands: 20, Arbor Diameter: 1.5", Roll Space: 12", Horizontal Centers: 13", Vertical Centers: 4" to 7", Speed: 0 to 100 FPM, Motor: 40 HP, Location: OH, Spec Sheet, DAHLSTROM 400-20OB, Weight. 999.
20 Stand, Dahlstrom #450-22OB, rollformer, 2" shaft diameter, 4.5"-5.75"vertical, 24" roll space, 10" horiz centers, 30-90 FPM
D & H Machinery Inc | Toledo, OH
Category: Rollformers
Seller: D & H Machinery Inc
Location: Toledo, OH
Mfr: Dahlstrom
Model: 450-22OB
Dahlstrom Rollformer, -Model: 450-22 OB, -Stands: 20 on a 22 Stand Base, -Shaft Diameter: 2.00", -Vertical Adjustment: 4.50" - 5.75", -Roll Space: 24", -Horizontal Centers: 10", -Base to Center of Bottom Shaft: 5.50", -Floor to Top of Base: 34", -Speed Range: 30 - 90 FPM, -Electrics: 440 V/3 PH/60 HZ, -Operators ...more
20 Stand, Max Roll, 1-1/2" spdl, 11" roll space, 9" horz.center, 2-1/2" vert.adj., #2996
Universal Tube & Rollform | Perrysburg, OH
Category: Rollformers
Seller: Universal Tube & Rollform
Location: Perrysburg, OH
Mfr: Max Roll
UTUBE NUMBER: 2996, MANUFACTURER: MAX ROLL, Number of Stands: 21, Missing 1 Inboard, Line Direction: Left to Right, Spindle Diameter: 1-1/2", Roll Space: 11", Horizontal Center: 9", Vertical Adjustment: 2-1/2", Base Top to Center Lower Spindle: 4", Spindle Key Size: 3/16, Gearing: 25-1, Electrics: ...more
20 Stand, Michigan #RMT-200-20, rollformer, 2" shaft diameter, 14" roll space, 50 HP, #74977
Yoder Machinery Sales | Holland, OH
Category: Rollformers
Seller: Yoder Machinery Sales
Location: Holland, OH
Mfr: Michigan
Model: RMT-200-20
SERIAL. 80829, MODEL. RMT-200-20, NUMBER OF STANDS. 20, SHAFT DIAMETER. 2", ROLL SPACE. 14", HORIZONTAL CENTERS. 15", LOWER SPINDLE CENTER TO BASE. 7-1/4", VERTICAL ADJUSTMENT. 4-1/2" TO 9", GEAR RATIO. 1 TO 1, AIR CLUTCH. WICHITA, VASRIABLE SPEED DRIVE. ALLEN BRADLEY 1336 PLUS, MOTOR HORSEPOWER. 50.
20 Stand, Pearson Rake & Gutter Rollforming Line, 2.5" arbor, 30" roll space, 16" horiz spacing, 5"-10" vert adj.
G-2000 | Toledo, OH
Category: Rollformers
Seller: G-2000
Location: Toledo, OH
Mfr: Pearson
NUMBER OF STANDS.: 20. TWO SEPERATE BASES OF 10 AND 10, ARBOR DIAMETER.: 2.5", ROLL SPACE.: 30", HORIZONTAL SPACING.: 16", VERTICAL ADJUSTMENT.: 5" TO 10", Machine Type.Roll Formers Manufacturer.PEARSON Model.N/A Year.N/A Condition.Used.
20 Stand, Tishken Rollformer, 2" OD shafts
AM Industrial | Brook Park, OH
Category: Rollformers
Seller: AM Industrial
Location: Brook Park, OH
Mfr: Tishken
TISHKEN 2" 20 Stand Rollformer - Used - AM23271, Bases: 2 Stands: 20 Spindle Size: 2" Roll Space: 8.5" Approx. Roll Space Horizontal Centers: 12" Approx. Includes:, Machine Mounted Push Button Operator Controls Tishken Drive Train No Tooling Included, Call us!, We will load for free - Shipping rates available!.
20 Stand, Tishken Rollformer, 12" W, 24 Ga., 10000 lb. Capacity, Servomatic IV Feed, 15-1/2" Shut Height, 40 Ton, 3" Stroke, 45 SPM, AMS Control
VX Machinery | Sylvania, OH
Category: Rollformers
Seller: VX Machinery
Location: Sylvania, OH
Mfr: Tishken
, Width: 12", Stands: 20, Spindle Diameter: 2", Gauge range: 24 Gauge, Product: Access Door Back Panel, Includes:, Mandrel Uncoiler, -36" wide Mandrel Uncoiler, -10,000 Lbs. Weight Capacity, Servomatic IV Press Feed Unit, 40 Ton x 3" Rousselle Straight Side Press, -Model 4S56, -Shut Height: 15-1/2", -Tonnage: 40 ...more
20 Stand, Yoder #M3, rafted roll forming heads, 3 spindle diameter, 18" roll space, equal geared
Yoder Machinery Sales | Holland, OH
Category: Rollformers
Seller: Yoder Machinery Sales
Location: Holland, OH
Mfr: Yoder
Model: M3
TOTAL NUMBER OF STANDS. 20, NUMBER OF RAFTS. 5, STANDS PER RAFT. 4, SPINDLE DIAMETER. 3", ROLL SPACE. 18", HORIZONTAL DISTANCE BETWEEN SPINDLE. 24", DISTANCE BASE TO CENTER OF LOWER SPINDLE. 10", MIN VERTICAL CENTER DISTANCE BTWN SPINDLES. 5-1/2", MAX VERTICAL CENTER DISTANCE BTWN SPINDLES. 9", EQUAL GEARED. YES.
20/36 Stand, Quato, r Rafted Quick-change Panel Roll Forming Line w/ Stacker, R-L, 100mm shaft diameter, 230mm vertical center, 35 MPM
National Machinery Exchange | Newark, NJ
Category: Rollformers
Seller: National Machinery Exchange
Location: Newark, NJ
21 Stand, PM Machine Tool rollformer, 4-1/2" arbor, 60" roll space, egual gearing, #70354
Yoder Machinery Sales | Holland, OH
Category: Rollformers
Seller: Yoder Machinery Sales
Location: Holland, OH
Mfr: Pm
SERIAL. 80-277, STANDS. 21 (ROOM FOR 24), ARBOR DIAMETER. 4-1/2", ROLL SPACE. 60", HORIZONTAL CENTERS. 24", VERTICAL ADJUSTMENT. 8" TO 14", CENTER OF BOTTOM SPINDLE TO BASE. 12", GEARING. EQUAL 1:1, ENTRY GUIDE. YES, PINCH FEED ROLLS. YES, CENTER DRIVE MACHINE. YES, HEAVY DUTY GEAR BOXES. YES.
22 Stand, Ardcor, Rollformer, 4" arbor, 57" roll space, 16" horizontal center, 9" vertical distance bet. arbor
National Machinery Exchange | Newark, NJ
Category: Rollformers
Seller: National Machinery Exchange
Location: Newark, NJ
Mfr: Ardcor
SERIAL. 74250, MODEL. F-15-4-57, BASE STAND CAPACITY. 24, NUMBER OF STANDS. 22, DIAMETER OF ARBORS. 4", ROLL SPACE. 57", HORIZONTAL CENTERS. 16", VERTICAL DISTANCE BETWEEN ARBORS. 5" MIN, 9" MAX, BASE TO CENTER OF LOWER ARBOR. 6-1/2", GEARING. EQUAL, RATIO. 1 TO 1, ENTRY PINCH ROLLS. 54", ENTRY EDGE GUIDES, SHEET ...more
22 Stand, Dahlstrom #450-22-OB, 2.25" shafts, 28" roll space, 25-100 FPM, 2009
General Machinery LLC | Detroit, MI
Category: Rollformers
Seller: General Machinery LLC
Location: Detroit, MI
Mfr: Dahlstrom
Model: 450-22-OB
Year: 2009
22 Stand Dahlstrom Rollformer, Model: 450-22-OB, Serial# 0741285, Shaft Diameter: 2.25", Roll Range: 4.5" - 5.75", Roll Space: 28", Horiz Center: 10", Speed Range: 25-100 FPM, Motor: 25 HP DC, Line Volts: 460/3/60.
22 Stand, Proma #RF2-02, rollformer w/cutoff, 2" arbor, 18" roll space, 15" horizontal center, 6.9" vertical center, 1985
National Machinery Exchange | Newark, NJ
Category: Rollformers
Seller: National Machinery Exchange
Location: Newark, NJ
Mfr: Proma
Model: RF2-02
Year: 1985
PROMA #RF2-02 ROLL FORMING LINE WITH CUTOFF, YEAR 1985, 2" SHAFT DIAMETER, 18" ROLL SPACE, 15" HORIZONTAL CENTER, 6.9" VERTICAL CENTER, 60 DC MOTOR HP, SPINDLE GEAR RATIO 1.4:1, DRIVE HOUSING 15.5:1, 100 GALLON COOLANT TANK, ------, PROMA CUTOFF, #80 CP-02, YEAR 1985, S/N 04-45- DOOR-TEX, DRIVE MOTOR 20HP 1200 RPM ...more
22/24 Stand, Tishken #24HW, rollformer, 14" roll space, 3.5" arbor, 1997
G-2000 | Toledo, OH
Category: Rollformers
Seller: G-2000
Location: Toledo, OH
Mfr: Tishken
Model: 24HW
Year: 1997
SERIAL. 21939-299, YEAR NEW. 1999, MODEL. 24-HW-S-3-1/2, NUMBER OF STANDS. 22 (ON 24 STAND BASE), ARBOR SHARFT DIAMETER. 3-1/2", ROLL SPACE. 21", HORIZONTAL CENTERS. 14", VERTICAL ADJUSTMENT. 6-1/2" TO 8-3/8", LOWER SPINDLE TO BASE., GEARING. EQUAL, DIRECTION OF TRAVEL. LEFT TO RIGHT, FLOOR TO PASS LINE. 46", OPERATOR ...more
22 Stand, Tishken #24HW S3-1/2, Roll Forming Line, 3-1/2' ' spindle diameter, 20" roll space, 14" horizontal center, 9" vertical center
National Machinery Exchange | Newark, NJ
Category: Rollformers
Seller: National Machinery Exchange
Location: Newark, NJ
Mfr: Tishken
Model: 24HW
22 STAND ON 24 STAND BASE X 3-1/2" ROLL FORMING LINE, CONSISTING OF:, TISHKEN MODEL 24HW S3-1/2 ROLL FORMING LINE, Line Direction. Left to Right, # of Stands. 22 Stands on a 24 Stand B, Spindle Diameter. 3-1/2", Roll Space. 20", Horizontal Centers. 14", Vertical Centers. 7-1/2" to 9", Main Motor Drive. 75 HP, 500 ...more
22/24 Stand, Tishken #24HW-S-3-1/2, Accelerator rollformer, 2-1/2" shaft diameter, 1999
National Machinery Exchange | Newark, NJ
Category: Rollformers
Seller: National Machinery Exchange
Location: Newark, NJ
Mfr: Tishken
Model: 24HW-S-3-1/2
Year: 1999
, SERIAL. 21939-299, YEAR NEW. 1999, MODEL. 24-HW-S-3-1/2, NUMBER OF STANDS. 22 (ON 24 STAND BASE), ARBOR SHARFT DIAMETER. 3-1/2", ROLL SPACE. 21", HORIZONTAL CENTERS. 14", VERTICAL ADJUSTMENT. 6-1/2" TO 8-3/8", LOWER SPINDLE TO BASE., GEARING. EQUAL, DIRECTION OF TRAVEL. LEFT TO RIGHT, FLOOR TO PASS LINE. 46" ...more
23 Stand, Ardcor rollformer, 2.5" x 48", #3364
Universal Tube & Rollform | Perrysburg, OH
Category: Rollformers
Seller: Universal Tube & Rollform
Location: Perrysburg, OH
Mfr: Ardcor
Model: 3364
UTUBE NUMBER: 3364, MANUFACTURER: ARDCOR, MODEL NUMBER: F15-2-1/2-48, SERIAL NUMBER: 83-088, YEAR: 1983, Line Direction: Right to Left, Number of Passes: 24, Spindle Diameter: 2-1/2", Roll Space: 48", Horizontal Center: 16", Vertical Adjustment: 5" – 9", Base Top to Center Lower Spindle: 6-1/2", Spindle Key ...more
24 Stand, Dahlstrom #400-18UD/400-6UD, rollformer, 1-1/2" shaft diameter, 14" roll space, 13.5" horizontal centers, 7" vertical adj.
Universal Tube & Rollform | Perrysburg, OH
Category: Rollformers
Seller: Universal Tube & Rollform
Location: Perrysburg, OH
Mfr: Dahlstrom
Model: 400-18UD/400-6UD
UTUBE NUMBER: 4195, MANUFACTURER: DAHLSTROM, MODEL NUMBER: 400-18 UD/400-6 UD, SERIAL NUMBER: 1211/1212, Number of Passes: 24, Line Direction: Right to Left, Roll Shaft Diameter: 1-1/2″, Roll Space: 14″, Horizontal Centers: 13-1/2″, Vertical Adjustment: 4″ – 7″, Line Speed: 110 FPM ...more
24 Stand, Dreinstern, roll form line, 20" width, 1.5mm thickness, 2.5" shaft diameter, R to L, 60M/m
General Machinery LLC | Detroit, MI
Category: Rollformers
Seller: General Machinery LLC
Location: Detroit, MI
Mfr: Dreinstern
24 Stand Dreistern Roll Form Line:, 24 Roll Stands, Coil Width Max=20”, Max Material Thickness 1.5mm., Ultimate Tensile Strength Approx. 1150 N/mm2, Shaft Diameter 2.5”, Max Roll Tool Width=20 ½”, Vertical Spacing= 5”, Upper Shaft Adj= + 4.5”/ – 1”, Min Vertical Spacing ...more
24 Stand, Tishken #24-HWAS-3, rollformer, 3" spindle diameter, 40" adj. rollspace, 6-1/2"- 8-3/8" vertical adj., 14" horizontal centers, 39" passline, 1991
Universal Press & Machinery (UPM) | Ferndale, MI
Category: Rollformers
Seller: Universal Press & Machinery (UPM)
Location: Ferndale, MI
Mfr: Tishken
Model: 24-HWAS-3
Year: 1991
Serial Number: (20679-1091), Number of Stands: 24 (Two 12 Stand Bases), Spindle Diameter: 3”, Roll Space: 30” - 40” (Powered Adjustment), Gearing: Unequal 1.3 to 1, Vertical Adjustment: 6 1/2” to 8 3/8”, Horizontal Center: 14”, Passline Height: 39” (Approximately), Right to ...more
24 Stand, Tishken #24-HWS, 3" spindle diameter, 36" roll space, 40 HP, 14" horizontal centers, 1986
D & D Industries Inc | Monclova, OH
Category: Rollformers
Seller: D & D Industries Inc
Location: Monclova, OH
Mfr: Tishken
Model: 24-HWS
Year: 1986
Spindle Diameter 3 inches Number of Stands 24 Power 40 horsepower Horizontal Centers 14" Vertical Centers 13.5 "-14.25" With 1" of Verticaladjustment Base To Bottom Of Spindle 6" Roll Space 36" Gear Ratio Equal Coolant yes Dimensions 392" LR x 100" FB x 50" Tall Weight 50000 pounds, Auto Lube System, 1986, 2 Separate ...more
24 Stand, Tishken #24-MW-3, rollformer, 3" spdl diameter, 36" rollspace, equal gearing, automatic lube, 1984
Southern Fabricating Mchy Sales | Lithia, FL
Category: Rollformers
Seller: Southern Fabricating Mchy Sales
Location: Lithia, FL
Mfr: Tishken
Model: 24-MW-3
Year: 1984
3” X 36” Rollformer with Equal Gearing, Auto Lube, Entry Edge Guide and Variable Speed Guide., Number of Stands: 24, Spindle Diameter: 3”, Rollspace: 36”, Horizontal Distance: 14”, Vertical Adjustment: 6-½” - 8”, Lower Spindle to Base: 6”, Pass Line: 36” ...more
24 Stand, Clinton, rollformer, 3" arbor, 46" roll space, 14" horizontal centers, 5.5"-7" vertical adj., 39" passline, exit side rolls w/ tooling
Yoder Brothers Machinery | Toledo, OH
Category: Rollformers
Seller: Yoder Brothers Machinery
Location: Toledo, OH
SERIAL. 1685 5-77, MODEL. 24 STAND DOOR PANEL, STANDS. 24, ARBOR. 3", ROLL SPACE. 46", CAPACITY.019" TO.035", HORIZONTAL CENTERS. 14", VERTICAL CENTERS. 5.5" TO 7", BASE TO LOWER SPINDLE. 5.5", DRIVE GEARBOXES. 4, GEARBOX RATIO. 15:1, PASS LINE. 39", EXIT SIDE ROLLS. YES WITH TOOLING, MOTOR. 40 HP DC WITH CONTROLS.
26 Stand, Tishken #26HW-3, rollformer, 3" arbor diameter, 14" roll space, 14" horiz centers, #72239
Yoder Machinery Sales | Holland, OH
Category: Rollformers
Seller: Yoder Machinery Sales
Location: Holland, OH
Mfr: Tishken
Model: 26HW3
SERIAL. 21860-997, MODEL. 26HW-3, NUMBER STAND. 26, DIAMETER OF ARBORS. 3", ROLL SPACE. 12", HORIZONTAL SPINDLE CENTERS. 14", VERTICAL ADJUSTMENT. 6-1/2" TO 8-3/8", SPINDLE RATIO. 10 TO 1, EQUAL GEARING. YES, MOTOR IS IN BASE. 440 VOLT 73.6 KVA.
28/30 Stand, Dreistern #P915-P1815, rafted type U joint drive rollformer, 1986, #61598
Yoder Machinery Sales | Holland, OH
Category: Rollformers
Seller: Yoder Machinery Sales
Location: Holland, OH
Mfr: Dreistern
Model: P9SP-1815
Year: 1986
SERIAL. 86-2-62, NEW. 1986, MODEL. P915-P1815, NUMBER OF STANDS. 28 ON 30 STAND BASE, SHAFT DIAMETER. 1-1/2", ROLL SPACE. 12", VERTICAL ADJUSTMENT. 3" TO 5-1/4", BASE TOP TO LOWER SPINDLE CENTER. 4-1/2", RAFTED. YES, UNIVERSAL JOINT DRIVE. YES, EQUAL AND UNEQUAL GEAR BOXES. YES, VARIABLE SPEED DRIVE CONTROL. T B WOODS ...more
28 Stand, Tishken #HMW-1-1/2, rollformer, 1.5" shaft diameter, 8" roll space, 9" horizontal centers, 4"-8" vertical adj.
D & H Machinery Inc | Toledo, OH
Category: Rollformers
Seller: D & H Machinery Inc
Location: Toledo, OH
Mfr: Tishken
Model: HMW-1-1/2
28 Stand Tisken Rollformer, Consisting of:, Rollforming Section #1:, Model: 12-HMW-1 1/2, -Number of Stands: 12, -Shaft Dia.: 1.500", -Roll Space: 8.00", -Horizonal Centers: 9.00", -Center of Bottom Spindle to Base: 4.500", -Vertical Adjustment: 4.00", -Adjustment Range: 4" to 8", -Overall Size: 142" L x 48" W x 47" ...more
28 Stand, Yoder #M3, rafted rollformer, 3" spindle diameter, 18" roll space, equal geared, 1995
Yoder Machinery Sales | Holland, OH
Category: Rollformers
Seller: Yoder Machinery Sales
Location: Holland, OH
Mfr: Yoder
Model: M3
Year: 1995
SERIAL. Y10498-0905, MODEL. M3, YEAR. 1995, NUMBER OF STANDS. 16, SPINDLE DIAMETER. 3", ROLL SPACE. 18", HORIZONTAL DISTANCE BETWEEN SPINDLE. 24", DISTANCE BASE TO CENTER OF LOWER SPINDLE. 10", MIN VERTICAL CENTER DISTANCE BTWN SPINDLES. 5-1/2", MAX VERTICAL CENTER DISTANCE BTWN SPINDLES. 9", EQUAL GEARED. YES ...more
32 Stand, Contour #1532AOSLCE, rafted rollformer, 2.5" arbor diameter, 40" R/S, 1996, #69083
Yoder Machinery Sales | Holland, OH
Category: Rollformers
Seller: Yoder Machinery Sales
Location: Holland, OH
Mfr: Contour
Model: 32/52X 2.5 X 40
Year: 1996
SERIAL. FA134, MODEL. 1532AOSLCE, NEW. NOV 1996, STANDS. 32, ARBOR DIAMETER. 2.5".
32 Stand, Tishken #32-XHW-4, Rollformer, 4 1/2' ' spindle diameter, 70" roll space, 18" horizontal center, 11" vertical center, 1997
National Machinery Exchange | Newark, NJ
Category: Rollformers
Seller: National Machinery Exchange
Location: Newark, NJ
Mfr: Tishken
Model: 32-XHW-4
Year: 1997
MODEL. 32-XHW-4, YEAR. 1997, NUMBER OF STANDS. 32, SPINDLE DIAMETER. 4 1/2'', ROLL SPACE. 70", HORIZONTAL CENTERS. 18'', VERTICAL CENTERS. 8'' - 11'', US VARIABLE SPEED DRIVE. 100 HP, TOOLED FOR GMT900 PANEL, EQUAL GEARED QUANTUM III DIGITAL, DC DRIVE.
32 Stand, Tishken #32-XHW-4, 4-1/2" spdl, 70" RS, Quantum III digital DC dr, 1997, #55271
Yoder Machinery Sales | Holland, OH
Category: Rollformers
Seller: Yoder Machinery Sales
Location: Holland, OH
Mfr: Tishken
Model: 32-XHW-4
Year: 1997
SERIAL. 21823-10-97, MODEL. 32-XHW-4, YEAR. 1997, NUMBER OF STANDS. 32, SPINDLE DIAMETER. 4 1/2", ROLL SPACE. 70", HORIZONTAL CENTERS. 18", VERTICAL CENTERS. 8" - 11", US VARIABLE SPEED DRIVE. 100 HP, TOOLED FOR GMT900 PANEL, EQUAL GEARED, QUANTUM III DIGITAL DC DRIVE.
32 Stand, Tishken #32-XHW-4-1/2, 70" roll space, 4-1/2" spindles, Qunatum III, 1997
Planet Machinery Co | Grand Haven, MI
Category: Rollformers
Seller: Planet Machinery Co
Location: Grand Haven, MI
Mfr: Tishken
Model: 32-XHW-4-1/2
Year: 1997
61 Stand, RLM, rollformer, 3" spindle diameter, 25" spdl length, gearboxes & outboard stands
Universal Tube & Rollform | Perrysburg, OH
Category: Rollformers
Seller: Universal Tube & Rollform
Location: Perrysburg, OH
Mfr: Rlm
UTUBE NUMBER: 4071, MANUFACTURER: RLM, Number of Stands: 60+, Number of Gearboxes: 60+, Spindle Diameter: 3″ with 1/2″ Shaft Key, Spindle Length: 25″- 30″, Roll Space:, (55) Gearboxes: 20″, (4) Gearboxes: 22″, (4) Gearboxes: 24″, Equally Geared, Base to Lower Spindle: ...more
American, trim rollformer
G-2000 | Toledo, OH
Category: Rollformers
Seller: G-2000
Location: Toledo, OH
Mfr: American
Machine Type.Roll Formers Manufacturer.American Model.N/A Year.N/A Condition.Used.
Ardcor #MIOU-H-R, rollformer base, 30 HP, 1994
Yoder Machinery Sales | Holland, OH
Category: Rollformers
Seller: Yoder Machinery Sales
Location: Holland, OH
Mfr: Ardcor
Model: MIOU-H-R
Year: 1994
SERIAL NUMBER. 93-229, MODEL. MIOU-H-R, AGE. 1994, 24 STATION BASE, 24 5WW GEAR BOXES. 20:1, SHAFT SIZE. 2-3/4" X 1-1/4", MOTOR. 30 HORSEPOWER, NO ROLL STANDS, BASE WITH GEAR BOX.
ASC Shadow, Soffit/Liner Panel Rollformer, 10000 lb uncoiler, Roll feed, 50 feet conveyor
VX Machinery | Sylvania, OH
Category: Rollformers
Seller: VX Machinery
Location: Sylvania, OH
Mfr: Asc
-10,000 lb uncoiler, -Roll feed, -Shear, -50 feet conveyor, -Rollformer, -Shadow rib roll tooling, -Soffit roll tooling, Shadow Panel:, -24 Gauge, -18" Coverage, 3" x 5", Soffit/liner Panel:, -24 Gauge, -11" Coverage, 15/16" x 4" (optional).
B & K rollformer base, 225" x 88" x 27" H, #59897
Yoder Machinery Sales | Holland, OH
Category: Rollformers
Seller: Yoder Machinery Sales
Location: Holland, OH
Mfr: B & K
225" X 88" X 27" HIGH B & K ROLLFORMER BASE.
B & K, outboard stands (30 available)
Universal Tube & Rollform | Perrysburg, OH
Category: Rollformers
Seller: Universal Tube & Rollform
Location: Perrysburg, OH
Mfr: B & K
PRICE: $250 each, UTUBE NUMBER: 3578, MANUFACTURER: B&K, (10) B&K Outboard Stands, $250.00 Each – Please inquire with salesman for further., OVERALL DIMENSIONS: To Be Determined, APPROXIMATE WEIGHT: To Be Determined, LOCATION: Universal Warehouse, Perrysburg, Ohio, Searching for a Specific Machine? Our ...more
Birmingham #L-20 Rollform, Pittsburgh Lockformer, single phase, #7653
Vander Ziel Machinery Sales | Alto, MI
Category: Rollformers
Seller: Vander Ziel Machinery Sales
Location: Alto, MI
Mfr: Birmingham
Model: L-20
Serial # NA, Asset #7653, Capacity 20 ga to 26 ga, Depth of Pocket 5/16″, Width of hammer-over edge adjustable up to 3/8″, Speed 25 FPM, Motor 1 HP, Drive V-Belt, Stand Arc Welded Steel Heavy top Table, Dimensions 36″ x 16 1/2″ x 36 1/2″, Shipping Weight 320 lbs., Preliminary – ...more
