go to top
The World's Leading Online Marketplace for Used, New, and Surplus Industrial Machinery & Equipment ℠

Roll Mills

warning
44 Results

2. 5" x 5" Charles Ross & Son #2-5X5TRM, Stainless Steel, 3 roll, 1/2 HP

EcReCon Inc. | Pedericktown, NJ
Category: Roll Mills
Seller: EcReCon Inc.
Location: Pedericktown, NJ
, used Ross 3 Roll Mill, Bench Top Model 2.5x5 TRM. Has stainless steel type 440C hardened precision ground rolls with adjustable Teflon end plates. 0.5 HP. 208-230/460 volt Explosion Proof (XP) motor. Rolls are cored to allow water cooling or heating. Video of unit running available., CHARLES ROSS & SON 2.5X5 ...more

2.5" x 5.25" Torrey Hills Technologies #65, 3 roll lab mill, cored rolls for cooling

Ingalls Process Equipment | Painesville, OH
Category: Roll Mills
Seller: Ingalls Process Equipment
Location: Painesville, OH
Mfr: Torrey Hills
One (1) used lab Three Roll Mill Manufactured by Torrey Hills Technologies, USA Model: 65 Serial number: 7512 2.5" diameter x 5.25" long rolls Adjustable 1st and 3rd rolls Cored rolls for cooling Rolls show some surface rust Apron knife discharge Brass end guides with safety bar Safety shut off cable Single ...more

2.5" x 7" Douglas Aircraft #3B, 3 roll mill, Carbon steel, .75 HP, manual spacing adjustment on rolls

Machinery & Equipment Co | Brisbane, CA
Category: Roll Mills
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Douglas
Douglas Aircraft 3-Roll Mill, includes 2-1/2" Diameter X 7" Face Mild Steel Rolls. Manual spacing adjustment on rolls. Unit includes apron discharge, end plates and electrical panel. Driven by 3/4 HP, 220/440 Volts, 3-phase, 60 Hz, 1725 RPM motor. Foot pedal actuated., HP: 0.75, Measurements: 2.50" diameter X 7" face ...more

Douglas Aircraft #3-Roll Mill, 2-1/2" diameter X 7" face mild steel rolls, manual spacing, 0.75 HP, 1725 RPM, 220/440 V., foot pedal Control, w/ end plates

Aaron Equipment Co | Wood Dale, IL
Category: Roll Mills
Seller: Aaron Equipment Co
Location: Wood Dale, IL
Mfr: Douglas
used- douglas aircraft 3-roll mill. includes 2-1/2" diameter x 7" face mild steel rolls. manual spacing adjustment on rolls. unit includes apron discharge, end plates and electrical panel. driven by 3/4 hp, 220/440 volts, 3-phase, 60 hz, 1725 rpm motor. foot pedal actuated.

2.5" Bafang #S65, 65" mm x 125" mm, table top, 3 roll mill, 2015

Platinum Asset Services | Scarborough, ON
Category: Roll Mills
Seller: Platinum Asset Services
Location: Scarborough, ON
Mfr: Bafang
Year: 2015
BAFANG, S65, 65MM, X 125 MM, TABLE TOP, THREE ROLL MILL, 2015, BAFANG S65.

Get email updates for newly added Roll Mills

Roll Mills (also known as roller mills) are machines used for grinding, mixing, or refining materials by passing them through a series of rollers. Commonly used in industries like rubber, plastics, food processing, and metals, they are ideal for breaking down materials to achieve desired particle sizes or textures. Roll mills are essential for producing uniform materials and enhancing the consistency of various products.

3.75" x 8" Other, 3 roll Mill, manual adjustment, water cooled, less motor

Machinery & Equipment Co | Brisbane, CA
Category: Roll Mills
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Other
Kent Roll Mill. Compact 3-roll unit with manual adjustment. Measures 3-3/4" x 8". Lacks motor but is water-cooled for precise operation., Diameter: 3.75", Type: 3-Roll Mill, Basis: FOB.

4" x 8" Keith 3 roll mill, cored rolls, adjustable first & third roll, knife discharge, adjustable end guides, #25745 (2 available)

Federal Equipment Company | Cleveland, OH
Category: Roll Mills
Seller: Federal Equipment Company
Location: Cleveland, OH
Mfr: Keith
Used 4" x 8" Keith Three Roll Mill, 4" diameter x 8" long rolls, cored rolls, adjustable first and third roll, knife discharge, adjustable end guides, with approx. 1 HP motor, Serial No. 95021B.

4" x 8" Keith Machinery, 3 roll mill, adjust brass end guides, start/stop buttons

Ingalls Process Equipment | Painesville, OH
Category: Roll Mills
Seller: Ingalls Process Equipment
Location: Painesville, OH
Mfr: Keith
Stock Number: 4788, 4" x 8" Keith Machinery Three Roll Mill, /Spec Sheet:, One (1) used 4" x 8" Three Roll Mill Manufactured by Keith Machinery Serial number: 11206 Rolls: 4" x 8" long Adjustable brass end guides Safety cable emergency stop Cored rolls for cooling Apron knife for discharge Start/stop buttons Test run ...more

4" x 8" Keith Machinery #4X8, Horizontal Three Roll Mill, knife scraper w/discharge pan, 1 HP

Aaron Equipment Co | Wood Dale, IL
Category: Roll Mills
Seller: Aaron Equipment Co
Location: Wood Dale, IL
Mfr: Keith Machinery
used- keith machinery horizontal three roll mill, model 4x8. (3) 4" diameter x 8" wide cored rolls. adjustable end guides, knife scraper with discharge pan. driven by an approximate 1 hp motor. serial # 95021b.

4" x 8" Kent, 3 roll Mill, 1 HP, 208/230/460V

Machinery & Equipment Co | Brisbane, CA
Category: Roll Mills
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Kent
Kent Machine Works, 3-Roll mill, 4" diameter x 8" face, cored, mild steel rolls with 1 Hp Explosion Proof drive. Mill has manual roll sets for front and back rolls, complete with discharge apron. Drive is rated 208/230/460 volts, 3-phase, 60 Hz., HP: 1, Diameter: 4", Type: 3-Roll Mill, Basis: FOB.

4" x 8" Ross #4x8 TRM, floor model high speed 3 roll mill, 270 RPM, s/n #70520

Machinery Solutions Inc | Lexington, SC
Category: Roll Mills
Seller: Machinery Solutions Inc
Location: Lexington, SC
Mfr: Ross

4" x 8" Ross #4x8TRM, 3 roll mill, 1 HP, hand crank gap adjustment, scraper blades

Frain Industries | Carol Stream, IL
Category: Roll Mills
Seller: Frain Industries
Location: Carol Stream, IL
Mfr: Ross
Ross, Model 4 x 8 TRM, 3-Roll mill with volumes of product per hour – depending on materials and application. (3) 4" in diameter x 8" long rollers powered by 1 Hp motor drive, with hand crank gap adjustment, scraper blades and 8" long working roll area. All (3) rolls made of hardened steel. Roller ...more

4" x 8" Ross #4X8TRM, 3 roll mill, end guide holders less end guides, adjustable first and third rolls, #3047-4

Federal Equipment Company | Cleveland, OH
Category: Roll Mills
Seller: Federal Equipment Company
Location: Cleveland, OH
Mfr: Ross
Used Ross three roll mill, model 4X8TRM, 4" diameter x 8" roll faced width cored rolls, end guide holders less end guides, adjustable first and third rolls, knife apron discharge, approximately 1 hp motor with vfd controller, serial# 107948.

4" x 8" Ross #4X8, 3 roll-mill

EcReCon Inc. | Pedericktown, NJ
Category: Roll Mills
Seller: EcReCon Inc.
Location: Pedericktown, NJ
Mfr: Ross
, Used Ross 3 roll mill, chrome plated rolls 4" X 8". Model 4X8. SN 29708. Manual adjustments., ROSS., TYPE. ROLL MILL.

6" x 11-3/4" Buhler-Maig #6x11-3/4, 3 roll mill, 3 HP, hand crank gap adjustment, scraper blades

Frain Industries | Carol Stream, IL
Category: Roll Mills
Seller: Frain Industries
Location: Carol Stream, IL
Mfr: Buhler-Maig
Buhler-Maig, Model 6 x 11¾, 3-Roll mill with volumes of product per hour – depending on materials and application. (3) 6" in diameter x 11¾" long rollers powered by 3 Hp motor drive, with hand crank gap adjustment, scraper blades and 11¾" long working roll area. All (3) rolls ...more

6" x 12" Farrel 2-roll mill, cored rolls, micrometer roll adjust, end guides, knife disch, cabinet design, #49112

Federal Equipment Company | Cleveland, OH
Category: Roll Mills
Seller: Federal Equipment Company
Location: Cleveland, OH
Mfr: Farrel
Used Farrel two roll mill, 6" diameter x 13" faced rolls, cored rolls, micrometer roll adjustments, end guides, knife discharge, cabinet design, individually driven rolls each with 5 hp 208-220/440 volt motors, mechanical variable speed control, serial# 64A1473.

6" x 12" Stewart #6" x12", Pilot Two Roll Mill, 5 HP, 220/440 V

Aaron Equipment Co | Wood Dale, IL
Category: Roll Mills
Seller: Aaron Equipment Co
Location: Memphis, TN
Mfr: Stewart
used- stewart bolling 6" x 12" pilot two roll mill. approximate 6" diameter x 12" long chrome cored rolls. driven by 5 hp, 3/60/220/440 volt gear motor, single speed, fixed gear ratio. unit has front and back knee safeties, and over the roll safety cage. two point manual adjustment, split end guides. serial# 2560.

8" x 12" J.h. Day, 3 roll mill, cored & chromed rolls, manually adj.1st & 3rd rolls, brass end guides, knife discharge, #38699

Federal Equipment Company | Cleveland, OH
Category: Roll Mills
Seller: Federal Equipment Company
Location: Cleveland, OH
Mfr: J.h. Day
Used Lehmann three roll mill, 8" diameter x 12" wide faced rolls, cored and chromed rolls, manually adjusted first and third rolls, brass end guides, knife discharge.

8" x 16" Farrel, 2-roll mill, cabinet style, end guides, micrometer roll adjustments, #2930-29

Federal Equipment Company | Cleveland, OH
Category: Roll Mills
Seller: Federal Equipment Company
Location: Cleveland, OH
Mfr: Farrel
Used 8" x 16" Farrel two roll mill, cabinet style, end guides, micrometer roll adjustments.

9" x 24" Kent, Small Production Three Roll Mill, manual roll & apron set, manual roll temp. control, 10 HP

Aaron Equipment Co | Wood Dale, IL
Category: Roll Mills
Seller: Aaron Equipment Co
Location: Wood Dale, IL
Mfr: Kent
used- kent 9" x 24" small production three roll mill (trm). with manual roll set, manual apron set, and manual roll temperature control. probably driven through a silent chain drive by a 10 hp motor. does not have an electrical package.

10" x 22" J H Day, 3 roll Mill, 10/5 HP, 440V

Machinery & Equipment Co | Brisbane, CA
Category: Roll Mills
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: J H Day
J.H. Day 10" x 22" 3-Roll Mill - High-performance mill powered by a two-speed 10/5 HP motor. s manually adjustable rolls and is offered without guides or an apron. Rolls have not been reground (Serial #42651)., HP: 10', Diameter: 10', Type: 3-Roll Mill, Basis: FOB.

10" x 22" J.h. Day 3 roll mill, cored & chromed rolls, manual adjust 1st & 3rd rolls, brass eng guides, knife discharge, #38698

Federal Equipment Company | Cleveland, OH
Category: Roll Mills
Seller: Federal Equipment Company
Location: Cleveland, OH
Mfr: J.h. Day
Used Day three roll mill, 10" diameter x 22" wide faced rolls, cored and chromed rolls, manually adjusted first and third rolls, brass end guides, knife discharge.

12" x 12" Other, 2-Roll Mill, Flaking/cracking type, 15 HP

Machinery & Equipment Co | Brisbane, CA
Category: Roll Mills
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Other
Lehman 2-Roll Flaking Mill - 12 diameter x 12 wide rolls, cored for steam. Includes a 15 HP gearhead-driven motor. Designed for vegetable oilseed and grain flaking. Serial #1338., HP: 15, Diameter: 12", Type: 2-Roll Mill, Basis: FOB.

12" x 22" J.H. Day, 3 roll Mill, apron hooks, 6.5" inside diameter, 1-3/16" thick, 12" rolls

Ingalls Process Equipment | Painesville, OH
Category: Roll Mills
Seller: Ingalls Process Equipment
Location: Painesville, OH
Mfr: J.h. Day
one(1) set of used Apron Hooks for J.H. Day Three Roll Mill. Came off a 12" x 22" Day Three roll mill. Inside diameter is 6.5" (this would be the shaft size it bolts to) 1 3/16" thick. Casting number on back is 29123 weight: 38 lbs per set.

12" x 30" Ross, 3 roll-mill, Carbon Steel

EcReCon Inc. | Pedericktown, NJ
Category: Roll Mills
Seller: EcReCon Inc.
Location: Pedericktown, NJ
Mfr: Ross
, Used Ross 3 roll mill, carbon steel rolls approximately 12" X 30"., ROSS., TYPE. ROLL MILL.

13" x 32" Lehmann, 3 roll mill, 13" x32" face cored rolls, hyd.roll adj.on 1st & 3rd, brass end guides, top mtd.can tilter, flr.mtd, #46600

Federal Equipment Company | Cleveland, OH
Category: Roll Mills
Seller: Federal Equipment Company
Location: Cleveland, OH
Mfr: Lehmann
Used 16" x 32" Lehmann three roll mill, 16" diameter x 32" face cored rolls, Sight-O-Matic(micrometer) manual roll adjustment on first and third rolls, brass end guides, top mounted can tilter, knife discharge with stainless steel apron, approximately 60/30 hp two speed xp motor, silent chain driven, floor mounted.

14" x 30" J H Day #AN-08602, 3 roll Mill, 25 HP, 440V, 1170 RPM

Machinery & Equipment Co | Brisbane, CA
Category: Roll Mills
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: J H Day
JH Day, 3-Roll Mill, Model AN 08602, complete with 14" diameter x 30" face cored mild steel rolls. Mill has hydraulic roll sets for front and back rolls, complete with apron discharge. Mill has Explosion Proof 25 Hp, 440 volt, 1170 rpm, 3-phase, 60 Hz drive, serial number 4454. Mill is in very good condition, rolls ...more

14" x 30" J.h. Day 3 roll mill, cored rolls, manually adjusted first & third rolls, knife discharge, #23990 (2 available)

Federal Equipment Company | Cleveland, OH
Category: Roll Mills
Seller: Federal Equipment Company
Location: Cleveland, OH
Mfr: J.h. Day
Used 14" X 30" Day Three Roll Mill, 14" diameter X 30" long rolls, cored rolls, manually adjusted first and third rolls, knife discharge, end guides for first and second rolls, with motor.

14" x 30" J.h. Day 3 roll mill, cored rolls, manually adjusted first & third rolls, knife discharge, #24554

Federal Equipment Company | Cleveland, OH
Category: Roll Mills
Seller: Federal Equipment Company
Location: Cleveland, OH
Mfr: J.h. Day
Used Day Three Roll Mill, 14" diameter x 30" long rolls, cored rolls, manually adjusted first and third rolls, brass end guides, knife discharge, on base with motor, serial# 74880.

14" x 30" J.h. Day #1, 3 roll horizontal mill, 2 speed

McKean Machinery Sales Inc | Cleveland, OH
Category: Roll Mills
Seller: McKean Machinery Sales Inc
Location: Cleveland, OH
Mfr: J.h. Day
J.H. DAY #MODEL 1 14" X 30" 3 ROLL HORIZONTAL MILL :, -- 2 SPEED -- HP: 30/25 -- CURRENTLY WIRED 480V -- WGT: 9,000LBS. PRICE: FOB CLEVELAND, OH - - - $14,350.

16" x 40" Lehmann #631SV, 3 roll Vertical Mill, 60 psi Stainless Steel scraper knife holder, 75 HP, 230-460 V

Aaron Equipment Co | Wood Dale, IL
Category: Roll Mills
Seller: Aaron Equipment Co
Location: Wood Dale, IL
Mfr: Lehmann
used- lehmann 3-roll vertical mill, model 631sv. 16" x 40". enclosed helical gears with ration of 3.0:1 between the feed and fixed rolls, and a 2.02:1 ratio between the fixed and apron rolls; roll size is (actual) 15.75 diameter (40cm) x 40" (101.6cm) grinding length; air operated, approximately 60 psi stainless steel ...more

22" x 60" Farrel, 2-roll mill roll for 22" x 60" mill, cored, for driven side, #42126

Federal Equipment Company | Cleveland, OH
Category: Roll Mills
Seller: Federal Equipment Company
Location: Cleveland, OH
Mfr: Farrel
Unused Farrel two roll mill roll for 22" x 60" mill, cored, for driven side.

26" x 26" Adamson, 2-roll mill, 84" wide, unitized base, Falk gearbox with 79.288:1 gearbox rating, #3155-2

Federal Equipment Company | Cleveland, OH
Category: Roll Mills
Seller: Federal Equipment Company
Location: Cleveland, OH
Mfr: Adamson
Used 84" Adamson United two roll mill, 84" wide x 26" diameter, unitized base, Falk gearbox with 79.288:1 gearbox rating, 200 HP, 1180 RPM 460 Volt AC motor.

26" x 38" Farrel, cracker mill roll, front roll, cored for cooling, 17" bushing journals

Soberay & Sons Ltd | Cleveland, OH
Category: Roll Mills
Seller: Soberay & Sons Ltd
Location: Cleveland, OH
Mfr: Farrel
One (1) Used Farrel 26" x 38" Cracker Mill Roll, front roll, cored for cooling, 17" bushing journals, corrugated surface.

26" x 38" Farrel, cracker mill roll, rear drive roll, cored for cooling, 17" bushing journals

Soberay & Sons Ltd | Cleveland, OH
Category: Roll Mills
Seller: Soberay & Sons Ltd
Location: Cleveland, OH
Mfr: Farrel
One (1) Used Farrel 26" x 38" Cracker Mill Roll, rear drive roll, cored for cooling, 17" bushing journals, corrugated surface.

26" x 84" Adamson, Two-Roll Mill, 200 HP, 1180 RPM, 460 V

HGR24 | Euclid, OH
Category: Roll Mills
Seller: HGR24
Location: Euclid, OH
Mfr: Adamson
Inventory No. 0418-129-0003 Manufacturer Adamson Name 84" Adamson Two Roll Mill Arrival Date 06-05-2018 Dimensions L x W x H (inches) Unavailable Capacity 84'' Weight (lb.) 10000 Category Fabrication Condition Used, tested Available Quantity 1 Item Used 84" Adamson United Two Roll Mill, 84" Wide X 26" X 26" ...more

C.E. Raymond #73412, Roller Mill, (4) four plow bodies, 10-40 mm feed, 350 HP, 585 RPM, 4160 V

Aaron Equipment Co | Wood Dale, IL
Category: Roll Mills
Seller: Aaron Equipment Co
Location: Wood Dale, IL
Mfr: Combustion Engineering
used- c.e. raymond #73412 roller mill. directly driven by a 350 hp, 3/60/4160v, 585 rpm motor. unit is a gear and intermediate shaft, horizontal shaft assembly with pinion, external oil lubrication system, vertical shaft, mill bottom assembly with oil reservoir, spider assembly with caps, plow support assembly with ...more

FLSmidth/Loesche, High Pressure Grinding Roll Mill, 3 roller mill, 1250 HP, Versatile, 130 TPH

D'Angelo International | Bellingham, WA
Category: Roll Mills
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Flsmidth/loesche
FLSmidth/Loesche High Pressure Grinding Roll Mill, - 1250 hp, three roller mill, installed, - Versatile, integrated drying, grinding and classification, - For raw meal cement, cement blending or slag grinding, - Three spare rolls, - Spare gearbox, - Miscellaneous maintenance stock, - 125 - 130 TPH throughput.

Koppers #9x18, mill, 2 sets of rolls, 10 HP, includes vibratory feeder

Perry Videx LLC | Hainesport, NJ
Category: Roll Mills
Seller: Perry Videx LLC
Location: Hainesport, NJ
Mfr: Koppers
Used Koppers Mill, Model: 9x18, Serial: 79-2230, 2 sets of rolls, Driven by a 10 hp motor, Includes vibratory feeder, KOPPERS 9X18.

Koppers #9x18, mill

Perry Videx LLC | Hainesport, NJ
Category: Roll Mills
Seller: Perry Videx LLC
Location: Hainesport, NJ
Mfr: Koppers
Koppers 9x18.

Raymond #5057, Roller Mill Spare parts, (2) mill base, (2) side and whizzer, (1) 75 HP blower and motor, return air housing, (1) groove sheave, (1) unused camping ring for bowl ring

Machinery & Equipment Co | Brisbane, CA
Category: Roll Mills
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Raymond
Raymond Roller Mill Model 5057 Spare Parts - Includes (2) mill bases, (2) mill sides, and whizzers, a 75 HP blower and motor, air housing, groove sheave, and spider assembly., Basis: FOB.

Williams, 3 roll Mill, Comet type, 4' spinner sep, (2) fans, wind box, air lock feeders and ducting, 25 HP motor

Machinery & Equipment Co | Brisbane, CA
Category: Roll Mills
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Williams
Williams Roller Mill, 3-Roll Comet Type - Includes 4' spinner separator, two fans, wind box, airlock feeders, and ducting. Powered by a 25 HP main motor (1765 RPM) and 5 HP whizzer motor., HP: 25, Type: Comet Type, Basis: As Is, Where Is.

Bronze End Guides for a 3 Roll Mill, 12" diameter, 12" top, 11.5" top to point, Replaceable tip

Ingalls Process Equipment | Painesville, OH
Category: Roll Mills
Seller: Ingalls Process Equipment
Location: Painesville, OH
One(1) used Set of Bronze End Guides for Three Roll Mill. Came off a J.H. Day Three Roll Mill. 12" diameter Rolls. Top: 12" L - R Top to point: 11.5" Equiped with Replaceable tip Casting stamp on back side: P-10-B Set of two weighs: 24 lbs. Loc: Loc, e.

Batch Off System with Stacker

Federal Equipment Company | Cleveland, OH
Category: Roll Mills
Seller: Federal Equipment Company
Location: Cleveland, OH
Used batch off system with stacker.