go to top
The World's Leading Online Marketplace for Used, New, and Surplus Industrial Machinery & Equipment ℠

Grinding Mills - Ball, Pebble, Sag, Mining

warning
1 - 50 of 70 listings

8" x 4' Humbolt-Wedag #20U, Palla Vibratory Ball Mill

Machinery & Equipment Co | Brisbane, CA
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Palla
Humbolt-Wedag Palla Vibratory Ball Mill, Model 20U - Measures 8" in diameter x 50" long. Mounted on a stand. Was a demonstration unit for trade shows (no motor included). Serial number 20181., Diameter: 0.67', Type: Vibratory Ball Mill, Measurements: 8" Diameter X 50" Long, Basis: FOB.

2.6' x 4' Denver Ball Mill, 10 HP, steel liners, ball charge, infeed hopper w/spout feeder

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Denver
- Denver 30" Diameter x 54" long Ball Mill, - Steel liners, - Ball charge, - Incudes infeed hopper with spout feeder, - 10 HP drive motor, - Flywheel drive system, - Belt guard, - Gear guard, - Straight cut gears, - Mill and drive mounted on steel operating skid.

3' x 6' Tumbler Ball Mill, 78 teeth & 4" face bull gear, 30" width x 6' L hatch, 108 RP output, 15 HP, 1765 RPM, 230/460 V,

Machinery & Equipment Co | Brisbane, CA
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Other
Tumbler batch mill, 3' X 6', driven by a Baldor 15 HP, 1765 RPM, 254T frame, 230/460 volts motor with a Dodge Maxum gear reducer model DC84, Output RPM: 108, Ratio 17:1. Includes Spur Cut bull gear with78 teeth and 4" face, 30" wide X 6' long hatch, and smmothe rubber lining. Pinion Gear: 22 teeth, 4" ...more

4' x 5' Denver, Ball Mill, 37' diameter Sheave, rubber lined, 2-pc bull gear

Machinery & Equipment Co | Brisbane, CA
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Denver
Denver Ball Mill, 4' diameter x 5' long, s two piece bull gear, pinion shaft and sole plates, Block grease style pedestal bearings & Sole plates, Gear guard with gear spray nozzles, Pinion shaft belt driven with 5V / 5 Groove, 37' diameter sheave to an ODP electrical motor, Bolt on motor mount and belt ...more

5' x 3' SAG mill with 20 HP, Skid mounted, Chain-driven w/ rollers under shell

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
- Skid mounted, - Chain-driven with rollers under shell, - Falk gearbox Motor:, - 20 HP (15 kW), - 1750 RPM, - 256T frame, - 230/460 V, - 3 Ph, - 60 Hz.

Get email updates for newly added Grinding Mills - Ball, Pebble, Sag, Mining

Grinding mills are industrial machines used to crush and grind materials into smaller particles, typically used in mining to process ores and minerals. They operate by rotating a cylinder filled with grinding media (such as steel balls or pebbles) and the material being processed, breaking it down into finer pieces for further processing. Common types include ball mills, pebble mills, and SAG mills, each suited for specific grinding applications depending on the hardness and size of the materials.

5' x 10' Kinetics, ball mill, Tire Driven, (2) 50 HP WEG motors, (2) gearboxes w/ 2.0+ SF, New

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Kinetics
- New unused ball mill made in North America, - 1.5 x 3 meter internal shell dimension, less liners, - Single piece rolled steel shell, - Tire Driven, - Rubber liner package with installation hardware, - Rubber lined feed spout, - Wet grinding overflow discharge arrangement, - Discharge trommel, - Drive assembly ...more

7' x 5.5' Ball Mill with 100 HP, Scoop feeder, Shell access door, 8" bull gear face

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
- 7 x 5.5 ft grinding volume, - 100 HP induction motor, - Scoop feeder, - Shell access door, - 8" bull gear face, - 18 tooth pinion gear, - Straight cut gear teeth, - I-beam steel skid, - Babbitted trunnion bearings, - Belt drive, - Steel liners.

8' x 6' Hardinge, conical ball mill with 200 HP, Wet grinding, overflow discharge, Single piece shell w/ access hatch

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Hardinge
- 8 x 6 ft Hardinge conical ball mill on a steel skid, - Wet grinding, overflow discharge, - Single piece shell with access hatch, - Baldor motor: 200 HP, 3600 RPM, 460 V, excellent condition, - Falk gear reducer: 5.86:1 reduction ratio, 1.5 SF, - Liners installed, - Double helical gears, - New gear guards, - Mill ...more

8' x 6' Marcy, Ball Mill, 250 HP, w/trunion feed, discharge

Machinery & Equipment Co | Brisbane, CA
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Marcy
Marcy 8' diameter x 6' long ball mill with trunnion feed and discharge. Rubber liners and lifters. Last used in a wet grind application. Previously driven by 250 HP motor thru gear & pinion. Gears good. Lots of wear on (1) of the trunnions. Mill serial number 700. Previously used in silica sands ...more

8' x 17' Kennedy Van Saun ball mills, 400 HP, gear box 6.95 ratio, air clutch, rubber liner, (3 available)

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Kennedy
-3 Available, -Siemens 400 HP 4,000 Volt Motor, -With Falk Gear Box 6.95 Ratio, -Eaton Air Clutch, -Low & High pressure Bearing Lube system, -Rubber Liners, -Plates and guards, -Single Helical Main Gears and Pinion Gears, -Grinding Media Available Upon Request.

8.5' x 13.5' Outotec Ball Mills with450 HP, unused, never instealed or operated (2 available)

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Outotec
- Unused Outotec Ball mills, - Delivered to site, never installed or operated, - 2 units available, - 8.6 x 13.5 ft mill shell (3.2 x 5.6 m), - Trunnion supported ball mill, - Ring and pinion gear drive, - Mill drawings available, - 450 HP WEG motor (340 kW), - 575V, 60 Hz, 3 Ph, - 1800 RPM, - SF 1.0.

9' x 7' Allis-Chalmers, for wet grinding & overflow discharge, 2-doors, cast heads, 259 tooth main gear

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Allis-Chalmers
- 9 ft dia x 7 ft length ball mill, - Manufactured by Allis Chalmers, - Configured for wet grinding and overflow discharge, - Mill components disassembled, inspected, cleaned, refurbished, and painted, - mill shell with 2 doors, - Cast heads, - New rubber liner set available separately, - Herringbone cut main and ...more

9' x 10' Allis-Chalmers, ball mill with 400 HP motor, Feed and discharge heads, overflow discharge, wet grinding

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Allis-Chalmers
- 9 x 10 ft Allis Chalmers ball mill, - Feed and discharge heads, - Configured for overflow discharge and wet grinding, - 2 piece bull gear with 248 teeth and 13 inch face, - 20 tooth pinion with assembly, - 2 lubrication pumps with 0.5 HP motors and air receivers, - Discharge trommel, - Removed and in storage, - ...more

9' x 10' Allis-Chalmers, Ball Mill, 400 Ton/day, 400 HP, 257 RPM, 550 V, 2-pc. Bull gear, 5-pc. Gear guard

Machinery & Equipment Co | Brisbane, CA
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Allis-Chalmers
Allis Chalmers Ball Mill, 9' diameter x 10' long, driven by 400 HP motor. Previously used in gold mining operation at approximately 400 tons per day. s Welded Steel Shell with Feed and Discharge Heads, Bronze Main Bearings Complete with Sole Plates, 2-Piece Single Helical Bull Gear with 5-Piece Gear Guard ...more

9' x 12' Allis-Chalmers, Rod or Ball Mill with 400 HP, Herringbone bull gear and pinion

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Allis-Chalmers
9 x 12 ft. Allis Chalmers Rod or Ball Mill w/ 400 hp, - Herringbone (1 piece) bull gear, 302 teeth, 20 in. face, - Herringbone pinion, 30 teeth, 20 in. face, - Westinghouse 400hp, 750 rpm, 575 volts, - Model SR-2614 reduction gear, 720 rpm input, 160 rpm output, 4.571:1Output: 160 R.P.M., SPARES (Additional cost): ...more

9.6' x 14' Dominion Engineering, Grinding Mill, 1-1/4" thick shell, 40" diameter x 24" width babbit bearings

Machinery & Equipment Co | Brisbane, CA
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Dominion
Dominion 9'6" diameter X 14' long Grinding Mill with 500 HP, 2300 Volt, 3/60Hz Synchronous motor. Shell measures 1-1/4" thick. Includes 24" diameter Wichita Pneumatic Air Clutch and 40" diameter X 24" wide self-aligning Babbit Bearings. Includes Farval manual bearing startup lubrication system. Currently used ...more

10' x 10' Kurimoto Iron Works, Ball Mill, 1020 ton/day, 500 HP, wet overflow discharge

Machinery & Equipment Co | Brisbane, CA
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Kurimoto Iron Works
Kurimoto 10' x 10' Ball Mill - Wet overflow discharge ball mill with a 10' diameter and 10' length, manufactured by Kurimoto Iron Works Ltd in 1969. Rated to process up to 1020 tons per day with a 500 HP power requirement. Offered without motor, balls, or liners., HP: 500, Diameter: 10, Type: Wet ...more

10' x 14' Allis-Chalmers, Ball Mill, 800 HP, 275 RPM, 4160 V, helical pinon gear, rubber liners

Machinery & Equipment Co | Brisbane, CA
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Allis-Chalmers
Allis Chalmers Ball Mill - Measuring 10' in diameter and 14' in length, this ball mill is driven by an 800 HP Westinghouse synchronous motor (3-phase, 275 RPM, 4160 volts). It includes a helical pinion gear, rubber liners, trunnions, Babbitt bearings, and a lubrication system, guaranteeing optimal ...more

10' x 14' Marcy Ball Mill with 800 HP motor, Overflow discharge, Pinion, 1.5 SF

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Marcy
- Overflow discharge, - Previously NDT tested, - Lincoln gear-spray lubrication system, - March 650-AL trunnion bearing lubrication system, - New spare bronze insert, - Ring gear, - Pinion, - Eaton Airflex 28VC650 dual narrow air clutch, Falk parallel shaft gear reducer:, - 4.792:1 reduction ratio, - 1.5 SF, Motor:, - ...more

10' x 18' Allis-Chalmers, Ball Mill, 800 HP, wet overflow type

Machinery & Equipment Co | Brisbane, CA
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Allis-Chalmers
Allis-Chalmers ball mill, 10' diameter(3082 mm) x 18' long(5486 mm), wet overflow type, serial number C2482. Complete with bull gear and pinion drive through speed reducer. Motor no longer available No liners., HP: Less Motor, Diameter: 10, Type: Wet Overflow, Measurements: 10' Diameter X 18' Long ...more

10.5' x 13' (3 x 4 m) Allis Chalmers, Ball Mill parts

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Allis-Chalmers
Shell- One piece, Forty-Eight 40 mm diameter bolt holesTwo Trunnion Bearings- Bearing journal with insert- Inside diameter- 1132 mm- Two bases in good conditionRing gear cover - 5 pieces (SOLD)Trunnion and motor base plates, 2 pinion drives with couplings (SOLD), 1 drive shaft (SOLD), 1 babbitt bearing (SOLD).

10.5' x 18.5' Outotec Ball mill with 1000 HP, cast mill heads, unused surplus (2 available)

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Outotec
- Unused surplus Outotec ball mills, - 2 matching units available, - Delivered to site, never installed or operated, - 10.5 x 18.4 ft mill shell (3.2 x 5.6 m), - Cast mill heads, - Trunnion supported mill, - Ring and pinion gearset, - Overflow discharge, - Drawings available, - Mills immediately available, - 1,000 HP ...more

10.6' x 14' Marcy, Ball Mill, 1000 kW transformer, 196" teeth & 21" face helical gear, 800 HP, 1170 RPM, 4160 V, overflow discharge

Machinery & Equipment Co | Brisbane, CA
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Marcy
Marcy Ball Mill, 10' 6" diameter x 14' long, driven by 800 HP motor, 1170 RPM, 4160 V, 3-phase, 60 Hz. Includes starter and 1000 kW transformer and mill control center, helical gear with 196 teeth, 21" face, overflow discharge, Lincoln gear-spray lube system, trunnion bearing lube system, air clutch, and gear ...more

11' x 14' Hardinge Koppers, Ball Mill, 48" diameter x 15" width trunnion journals, mill shell, bull gear

Machinery & Equipment Co | Brisbane, CA
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Hardinge Koppers
Hardinge-Koppers Ball Mill, 11' x 14', no motor. Includes mill shell, bull gear, feed and discharge heads with trunnion liners, shell liners, and gear covers. Trunnion journals measure 48" diameter x 15" wide., HP: Less Motor, Diameter: 11, Measurements: 11' Diameter X 14' Long, Basis: As Is, Where Is.

11' x 14.5' Dominion Engineering, Ball Mill, mill shell, bull gear, gear covers

Machinery & Equipment Co | Brisbane, CA
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Dominion
Dominion 11' x 14.5' Ball Mill. Includes the mill shell, bull gear, trunnion, feed liner, pinion, bearings, and gear covers but no motor., HP: Less Motor, Diameter: 11, Measurements: 11' Diameter X 14-1/2' Long, Basis: As Is, Where Is.

12' x 5' Outotec, Unused Surplus SAG Mill with 350 HP

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Outotec
- Unused surplus Meso Outotec SAG mill, - Still in factory packaging, - Delivered, never installed or used, - 12.1 ft diameter (3.7 m), - 5 ft length (1.5 m), - Trunnion supported mill with ring and pinion gearset, - 350 HP (250 kW) variable speed drive, 575V, - Metallic liners, - Grate discharge, - Immediately ...more

12' x 6.5' Abb, Single Drum Mine Hoist, Type HTDE-144 inch, 2000 FPM, 1.75" diameter rope

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Abb
12 x 6.5 ft (4 x 2 m) ASEA single drum mine hoist, – Type HTDE-144 inch, – ASEA 2,100/4,080 kW, 1000 VDC drive hoist motor, – 2,000 feet per minute, – 3,000 foot depth, – For 1.75 inch diameter rope, – 66,000 Lbs. maximum static rope stress, – Double disc brakes on drum with ...more

13' x 18.6' Nordberg, Rod/ Ball mill with 1500 HP motor

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Nordberg
- 1500 hp (1125 kw) AC 60 Hz synchronous motor, 225rpm, - Eaton Fawick air clutch 46VC 1200, - Mill shell and cast heads, - Feed and discharge trunnions and liners, - Trunnion bearing assemblies, - Refurbished girth gear (2 pcs), 570 mm wide, 310 tooth, 1.25 DP helical cut., - Pinion shaft assembly, 21 tooth pinion ...more

13.5' x 4' Marcy, SAG mill with 300 HP motor, designed for dry grinding, 1787 RPM

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Marcy
- 13.5 x 4 ft shell, - Originally designed for dry grinding, - removed, disassembled, and in storage ready for inspection and shipping, - Mill trunnions and wear parts protected during storage, - Trunnion bearings cleaned and in good condition, - Gears in good condition, - Includes a Falk gearbox, air clutch, and ...more

13.5' x 4' Marcy, Dry Grind Sag Mill, 300 HP motor (not included) 1988

Machinery & Equipment Co | Brisbane, CA
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Marcy
Year: 1988
Marcy Dry Grind SAG Mill, 13' 6" Diameter x 4' Long. Includes bull gear, pinion gear, large Falk gearbox, air clutch, and lube set. No motor. Manufactured new in 1988., Diameter: 13.5', Measurements: 13'6" Diameter X 4' Long, Basis: As Is, Where Is.

13.5' x 20' Nordberg rod mill, 2000 HP

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Nordberg
- Nordberg 13.5 ft diameter x 20 ft length Rod Mill- 2,000 HP (1,500 kW) Electric synchronous motor- 60 Hz and 4000V- 210 RPM- 6000 frame, - Manufactured in Canada- Used steel liner package, removed for shell and head inspection, - Double-wave pattern liners.

14' x 23' Kobe Steel/Allis Chalmers, Ball Mill, 120 MT/hr., 150 MT grinding media capacity

Machinery & Equipment Co | Brisbane, CA
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Allis-Chalmers
Kobe Steel/Allis Chalmers, 14' (4.2 m) diameter x 23'(7 m) long ball mill. Unit has feed & discharge trunnion Bbaring housing and inserts. Unit is missing pinion gear, pinion shaft, bull gear, lube system and motor. Grinding capacity at previous installation was 120 MT per hour, single compartment ...more

14.5' x 28' Allis-Chalmers, ball mill, 3000 HP, Configured for wet overflow discharge

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Allis-Chalmers
- 2 mills available: 14.5 x 28 ft (4.4 x 8.5 m), - Configured for wet overflow discharge, - 2 piece mill shell, - Trunnions with liners, - White metal trunnion bearing journals, - 289 tooth two-piece bull gear, - Bull gear guards, - 24 tooth pinion, - Falk gear reducers: 4.096:1 ratio, - One inching drive available ...more

15' x 19' Nordberg, Ball Mill with 3000 HP motorw, wet grinding, overflow discharge, Farwick dual clutch

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Nordberg
- 15 x 19 ft mill shell, - 2 piece shell, - Configured for wet grinding and overflow discharge, - 3,000 HP Westinghouse synchronous motor, 240 RPM 4160 V, - Containerized motor controls, - Farwick dual clutch.

15' x 20' Nordberg (Metso) ball mill shell w/cast heads (3 available)

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Nordberg
- 15 x 20 ft mill shell with cast heads, - Removed from installation and disassembled for inspection and shipment, - Spur cut main gear, - Rubber liner backing, - Steel shell and head liner package with single wave profile, Electric Synchronous Motor, - 3,000 HP 240 RPM, - 4,000 V and 3 Ph 60 Hz, - Frame 6000, - ...more

18' x 10.5' Fuller FLS, SAG mill with 1500 HP motor, Rubber-lined, 1995

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Fuller
Year: 1995
SAG mill, 18 ft diameter, 10.5 ft length.- Manufactured by Fuller 1995, - Rubber-lined, used rubber liners included, - 1500 HP, 4160 volt, 1192 RPM, continuous motor, 5010 frame Motor, rebuilt and inspected., - Spare used motor available- Moventas gear reducer, 4.5:1 gear ratio, 264.4 output RPM., - Motors are VFD ...more

18' x 27' Citic, Ball Mill with 5500 HP motor, Rubber liners

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Citic
Unused 18 x 27 ft (5.5 x 8.1 m) Citic Ball Mill with 5,500 HP (4,100 kW) 893 RPM WRIM induction motor., - Rubber liners, 2 sets, - High- and low-speed drive couplings, - Sole plates, Additional motor info:, -WRIM - 893 RPM, - 4160 Volt, - 3 Phase, - 60 Hertz.

18' x 30' Outotec, SAG Mill with 6300 HP motor, Unused surplus, 2013

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Outotec
Year: 2013
18 x 30 ft ( 5.5 x 9.15 m) Outotec SAG Mill with 6032 HP (4500 kW) motor:, - Unused surplus., - Made in 2013., - Includes: Lube system, feed chute, trommel, instrumentation, inching drive, and mill liners., - WEG 50 Hz wound Rotor Induction Motor: 11,000V, 994 RPM, Size MA710B, Enclosure CACA IC 611, 6 Pole, 3 Ph ...more

19.35' x 27.88' Morgardshammar, 550 mm width pinion, (2) 1877 HP, No liners included

Machinery & Equipment Co | Brisbane, CA
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Morgardshammar
Morgardshammar pebble/sag mill, 19.35' (5.9 m) diameter x 27.88' (8.5 m) long, 2-1,877 hp (1,400 kW) motors. Currently configured as a grate discharge sag or pebble mill. No liners included. Units consists of: shell (6 pcs, three cans, split horizontally), feed end head (1 piece), discharge end head (2 ...more

20' x 10' ANI/FLSmidth, SAG Mill with 2,500 HP motor, Enclosed gear drive, Lube system

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Ani/flsmidth
- 20 ft diameter by 10 ft shell (6.1 x 3.05 meter), - Manufactured by ANI/FLS, - Includes WEG 2,500 HP motor, - Enclosed gear drive made by David Brown, - Inching drive, - Mill is currently operational and installed, - Discharge trommel, - Lubrication systems, - Electrical control systems, - Liners installed, - Grate ...more

21' x 11' Hardinge, SAG mill with 2875 HP DC Motor, w/o liners and bolt package, Nuttall gear reducer

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Hardinge
21 x 11 ft Hardinge SAG mill with 2,875 HP- Mill is currently removed and in storage, - Without liners or bolt package, - Nuttall gear reducer, - McLellan liner handler available separately, - Spare motor available, - Operated in a Newmont Goldcorp plant, Toshiba 2,875 HP D.C. motor with variable speed drive- 240 RPM ...more

22' x 7' Hardinge, SAG Mills, Motor Quoted separately, Shell reconditioned

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Hardinge
22 ft x 7 ft (7 x 2 m) Hardinge SAG Mills, - Motor Quoted separately, - Previously ran on two 800 HP motors, - Dual Flender gearboxes, - Shell reconditioned.

22' x 36.5' FL Smidth, Ball Mill, (2) 6662 HP motors, qty. 2

Machinery & Equipment Co | Brisbane, CA
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Fl Smidth
(2) Unused 22' diameter x 36.5' long FL Smidth Ball Mills, with dual pinion motor drives. s fabricated shell, cast heads, Falk girth gear and dual pinon with spherical roller bearings, gear lube system, main bearings with sole plates, hydrostatic main bearing lube system, (2) ABB 4,900 kW (6,662 HP) low speed ...more

22' x 38' Metso Ball Mill with 13400 HP, (2) 6,700 HP motor, 680 TPH hard ore, 975 TPH soft ore, Unused, 2007

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Metso
Year: 2007
Unused surplus Metso Ball Mill, - Two available, - Manufactured in 2007, - Motor: Two TECO 6,700 HP induction motors, - 6 pole - 10,000 volt, - Wound rotor motors, - Processing capacity:, - Hard ore: 680 tons/hour, - Soft ore: 975 tons/hour.

22' x 38' Metso, Ball Mill, 13410 HP motor, 6075 HP rotor, overflow ball mill, rubber liners

Machinery & Equipment Co | Brisbane, CA
Seller: Machinery & Equipment Co
Location: Brisbane, CA
Mfr: Metso
Unused 22' diameter x 38' long Metso Ball Mill, with 10,000 kW (13,410 HP) fixed speed dual motor-gearbox-pinion drive. Designed as an overflow ball mill with rubber liners. Includes lube systems, feed chute, jack cradles, currently less liners, trommel, hydraulic lifting jacks, main HV switchgear. Each of the ...more

22' x 41' Metso, Ball Mill with 13400 HP, (2) GE 6700 HP, Shell in 4 Sections, 2013

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Metso
Year: 2013
Unused surplus 22 x 41 ft ( 6.7 x 12.5 m) Metso ball mill with 13,400 HP (10,000 Kw), - Motor: Two GE 6,700 HP (5,000 Kw) motors, - Manufactured in 2013, - Bull gear: 274 tooth helical gear. 4 pieces, with an 851 mm face, - Pinion gear: 19 teeth - Liners not included, - Shell in 4 sections.

24' x 8' Hardinge, SAG Mill with 3000 HP motor, 2 Flender gearboxes, Liners quoted separately

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Hardinge
- 2 Flender gearboxes, - Liners quoted separately, - 3,000 HP GE synchronous motor, - Mill is disassembled and in storage.

24' x 9' Boliden Allis, SAG Mill with 3000 HP motor, shell in 1 section, Steel liners

D'Angelo International | Bellingham, WA
Seller: D'Angelo International
Location: Bellingham, WA
Mfr: Boliden Allis
24 x 9 ft (7.3 x 2.7 m) Boliden Allis reconditioned SAG Mill with 3,000 HP (2240 kW) GE motor, - Mill shell in 1 section, - Inching drive, 3 piece, - Feed and discharge ends, - Shell and discharge liners, - Discharge end drive, - Trunnions, and trunnion lube system, - Bull gear: 332 tooth 0.5 m gear, - Pinion gear: 20 ...more