TIMESAVERS PUMA Model 52MWT-DD-75
Wet Process Abrasive Belt Deburring/Surface Finishing Machine.
The PUMA 52MWT-DD-75 has the following specifications:
Abrasive belt size: 52" x 75"
Main motors: 30, 30 HP
Maximum width stock: 51"
Minimum part length: 10"
Maximum thickness opening: 0-6"
Infeed loading area: 27"
Feed speed: 15-45 FPM
Approximate full load amps at 460 volt: 149
Motor type: TEFC
Pass line height: 32"-38", variable
Compressed air usage: 4 CFM @ 90 PSI
Approximate shipping weight: 11,400 lbs.
Your new Timesavers PUMA Model 52MWT-DD-75 wet process metalworking machine is equipped with two top heads, each being an 8" contact roll. It includes industry leading standard features, along with the optional features needed to meet your specific application needs. Here is why the superior design and construction of the PUMA 52MWT-DD-75 gives you the competitive edge.
ï± Contact Drums: (Both positions)
The sanding heads include dynamically balanced 8" diameter contact drums with precision bearings. Hardness (durometer) and serration are chosen for general deburring and finishing applications.
ï± Main Motors:
All abrasive head drive motors and feed drive motor are precision balanced for power and long life. Motors are TEFC, Totally Enclosed Fan Cooled for durability.
ï± Cam Adjustable Contact Drums:
Adjustable contact drums allow fine-tuning of abrasive belt pressure on parts without the need to adjust hold down rolls. This also allows the possibility of running abrasive belts of different thickness without having to adjust hold down rolls.
ï± Percentage Load Meters:
A load meter on each abrasive head displays exact percentage of main motor horsepower being used during operation.
ï± Through-Beam Abrasive Belt Tracking:
Electronic photo-eye tracking monitors and controls abrasive belt movement on the grinding head. Over-travel limit switches prevent abrasive belt damage in case of mistrack.
ï± Quick Release Outboard Support:
Allows fast removal of outboard support to expedite abrasive belt change. Abrasive belts can be changed in as little as 60 seconds.
ï± Dual Infeed and Dual Outfeed Hold down Rolls:
Rubber-covered, spring-loaded rolls aid in holding sheet metal parts onto the conveyor as they pass through the machine.
ï± Infeed Stop Bar:
A sheet metal gate which acts as an emergency stop for the operator when loading the machine. The gate actuates a limit switch which shuts down the abrasive belt head and conveyor feed in emergency situations.
ï± Variable Speed Conveyor Drive:
15-45 FPM variable frequency conveyor drive includes an LED speed display.
ï± Variable Pass line Height:
0-6" bed opening capacity with a 32"-38" conveyor pass line height.
ï± Motorized Thickness Adjustment:
Conveyor bed thickness setting is motor driven. This allows quick changes of thickness settings for material to be processed.
ï± Electronic Digital Thickness Readout:
An electronic thickness set-up device includes a “go-to" function with ability to store programs for ten thickness’ The readout also indicates conveyor bed position in relation to the grinding belt for accurate set-up to .001"
ï± Automatic Advance Paper Media Filter:
An integrated automatic indexing paper media filter cleans and re-circulates coolant for efficient deburring and finishing. This system comes complete with pump, controls, media paper and flow controls to advance the media automatically when needed.
ï± Air Knife Parts Dryer:
This system includes a high efficiency blower, precision top and bottom air knives and rubber squeegee rolls to remove excess coolant as parts exit the machine.
ï± Air Operated Disc Brakes:
Floating caliper disc brakes are used to stop the contact drum and brush head to assure consistent abrasive head stoppage in approximately four seconds. The braking system will not fade under continuous braking and has non-sparking, easily replaceable linings. The brake is located on the main motor shaft for easy maintenance.
ï± Centralized Control Panel:
Simple operator controls for machine operation. Conveyor feed, speed, coolant filtration, air knife dryer and abrasive heads are controlled at this centralized location.
About the Dealer
Sanson Machinery Group has been in business since 1970 serving Northern California and Nevada, expanding machinery sales and service, to Washington, Oregon, Idaho, Alaska and British Columbia with Sanson Northwest in 1984. We sell and service New and Used Machinery which is used in the Metalworking Industry. Sanson Northwest strives for Total Customer Satisfaction through continual improvement with Teamwork, Reliable Communication and Individual Job Excellence.