Manufacturer: Deimco / Blasdel
Model: 4-GUN FLATLINE SPRAY SYSTEM
Year: 2019
Type: 4-gun flatline spray system
Stock # FS-010771
For Sale by Ex-Factory

Surplus Record Dealer Since 2022
Location: Charlotte, NC
Contact Sales Dept.
Phone Number: 704...> Show Phone Number 704-285-2223
Let the seller know you found their listing on Surplus Record!
Description
Custom-Built DEIMCO Through Feed Sprayer with a BLASDEL IR Preheat Tunnel that is available MARCH of 2023. Until then, the System can be seen in operation. -- Line was designed to preheat Fiber Cement board prior to painting and is followed by a Single-Arm Reciprocating Sprayer with 4-Spray Gun cap. Spray Guns not included.SEE ATTACHED VIDEO FOR A GOOD LOOK AT THE LINE's OPERATION!Built in 2019, the System was used for approx. (2) years; current owner changed their process and no longer requires the equipment.Oven width cap.: 60" Wide, 1-3/4" part height cap.; overall Oven dimension: 84" Wide x 12-1/2' long x 55" high, excluding the Blower & Stack. Line/Conveyor: Variable speed drive, 18.5 FPM to 26 FPM; Reciprocator operates up to 260 FPM and set by the HMI. 2-Zone Oven: -- Zone 1: (2) Upper left side wall/ceiling mounted; 18" x 60" emitters. -- Zone 2: (2) Right upper side wall/ceiling mounted 18" x 60" emitters; 8" clearance between emitters & rolls. Heaters: Natural gas using 7" WC; 480 Volt preheat; TC, FM, flange frame. - Gas Ratings: 360,000 BTUH Max. input ; 100,000 BTUH standby input; Air Exhaust on infeed & Injection Blower on outfeed. Electrical ratings: 26.6 Amps, 480 V - 3 Phase, 60 Hz.Exhaust: 980 CFM, 1 HP Motor.Control Panel: 60 AMP Disconnect switch, ALLEN-BRADLEY "Panel View Plus HM", IEC contactor & High Temp PID exhaust.NOTE: (25) New replacement conveyor rollers & (40) reconditioned rollers for IR Tunnel.DIEMCO Sprayer complete with: (1) Reciprocating Arm holds (4) guns and reads the leading & trailing edge to turn on & off the guns as the parts feed through; best to run full width loads through Sprayer; Overspray funnels into buckets.Spray Guns turn on & off based on the part leading & trailing edge; read by a light curtain on the infeed end.Dims: GFS Spray Cabin: 13' Deep x 8-1/2' wide x 9' high surround the reciprocating arm. - Filter & Exhaust Section: 13' Wide x 3' Deep x 10' High.
Get Your Price from Ex-Factory!
Buyers Who Viewed This Listing Also Viewed:
4 Stage Stainless Steel powder Coating System, Nordson, with dry cure oven, 4" conveyor, (2) Nordson powder coating booths
Category: Paint and Powder Systems
Seller: Finishing Resources
Location: Cleveland, OH
Mfr: Nordson
Model: 4 STAGE STAINLESS STEEL POWDER COATING SYSTEM
5-Gun Automatic Powder Coating System, Nordson Sure Coat, Versa Spray II IPS guns
Category: Paint and Powder Systems
Seller: American Industrial Sales LLC
Location: Berlin, WI
Mfr: Nordson
Model: 5-GUN AUTOMATIC POWDER COATING SYSTEM
3 Stage Stainless washer, 36" W x 42" H part opening, 6 FPM, enclosed conveyor
Category: Paint and Powder Systems
Seller: KoteQuip LLC
Location: Elkhart, IN
Model: 3 STAGE STAINLESS WASHER
5' W x 7' H Powder Coating Line, Nordson
Category: Paint and Powder Systems
Seller: Syntec Systems Corporation
Location: Saukville, WI
Mfr: Nordson
Model: 5'W X 7'H POWDER COATING LINE
Year: 1995
2K / 3K / 4K plural component paint systems, new
Category: Paint and Powder Systems
Seller: Buy Rite Finishing
Location: Hastings, NE
Model: 2K / 3K / 4K PLURAL COMPONENT PAINT SYSTEMS
Plural Component Paints use two or more components to create a chemical reaction which causes the paint to harden. There are many reasons as to why a Plural Component Paint System is better than hand mixing!, EFFICIENCY Hand mixing requires a lot of repetition and labor, besides that.its just messy! Painting can be ...more































