Myers Technology Co LLC

like new never used 8' x 12 ga. Apron brake, Model HB97-12, Capacity, mild steel 12 gauge /, 2.7 mm, Bending length 97 in. /, 2464 mm, Maximum lift, of beam 2-1/4 in. /, 57 mm, Front to rear, beam adjustment 1/2 in. /, 13 mm, Minimum, reverse bend 1/4 in. /, 6 mm, Minimum flange in, capacity material 1 in. /, 25 ...more

32 ton, 0 to 700 strokes per minute, fixed bed, Tonnage : 32 Ton, Bolster Size: 24 x 15, Strokes/Minute: 0-700, Length of Stroke in inches: 1.50", Slide ADJ. in inches: 2.25", Shut-height on bed Stroke Down Adjustment Up in inches: 9.50", Clutch Air Pressure for rated tonnage in pounds: 55, Voltage/Phase/Frequency: ...more

Kaltenbach Automatic, Programmable Circular Saw for Straight and miter cutting Ferrous and non-ferrous metals, 15.74" Blade 5.1" Capacity Rd. at 90 degrees, Complete with Bundle loader, Universal Automatic Circular Sawing Machine for Straight & Miter Cutting of, Ferrous & Non-Ferrous Metals - Saw New in 2007 ...more

Koolrite 2290 Soluble oil one 55 gal. drum, New Coolants, Eliminate the Stink, Deliver Better, Machining Performance, Competitive Soluble Oil, Unique BioArmor Technology, Join the thousands of shops whove switched to, KOOLRite cutting fluids. Our unique Bio Armor, Technology delivers built-in resistance to, bacterial ...more

Brother model TC-32BN=QT Vertical CNC Drilling and Tapping center with Brother B00 control, 26 ATC, 2 Pallet changer, 7.3 KW spindle motor, Built 2008, TRAVELS:, -X AXIS: 21.7", -Y AXIS: 15.7", -Z AXIS: 16.3", PALLET SIZE: 23.6" X 16.7", SPINDLE: 12,000 RPM, RIGID TAP: 8,000 RPM, TOOL-TO-TOOL TIME: 0.9 SECONDS, PALLET ...more

Dainichi, Model W-16 200X 500 CNC Flat bed lathe with Fanuc 18T Control, 78.7 Swing X 196.8 Centers, 59 Swing over Cross slide, 55 4- jaw Chuck, 30 Way span middle to middle, 30 Capacity Steady rest, 4 Way toll post programmable, Chip conveyor, Mfgd 1999, Low hour was holding critical tolerances before disconnecting. ...more

Olympia V60L CNC VTL, CNC Vertical Turning Center, VTL, VTC, Live tooled VTL, C axis, Vertical turning center, Fanuc control, ATC, Table diameter 66", Maximum Swing 70", Standard Turning Diameter 68", Chuck Diameter 66", Maximum under rail 70", Table drive power 5, "X" axis travel 60, No. Of Tools 32, Control mfg. ...more

8,250 lb. capacity Hyster S80XM, LP lift truck, HI LO with 8' Forks, Side shift, Automatic transmission, new front tires, 145" lift height, HYSTER S80XM, Side Shift, Tilt wheel, 8 foot long forks, tilt gauge, newer seat and battery, Capacity. 8,250 lb, Lift Height. 145".

automatic horizontal hobber is differential and hob Shift, power draw bar with Collet chuck and collets, Extra large coolant tank, Manual tailstock, square cycles, good production style machine with manual loading, Barber Colman, horizontal Gear Hobber, Machine catalog are as follows:, MACHINE :, * Max. Rated Work ...more

Cosen C-260NC Fully Automatic Bandsaw, Cosen fully automatic horizontal bandsaw, Cut-off saw, Production saw, wet saw, NC saw, Round Cutting Capacity 10.2", Rectangle Cutting Capacity 10.2" x 11.8", Saw Blade Dimensions 1-1/4" X 12' X.043", Blade Speed 66-328 FPM, Main Motor, Saw blade 5 H.P., Hyd. Pump Motor 1 ...more

Denison 10 Ton Multipress has a 6 Position indexer and Light Curtains., Stroke 12", 10HP, Daylight 18, Throat 10, Ram Dia 2.5, Motor 1800 RPM, 20 GAL, 440 V 3 Phase 60 HZ.

Very good condition Geka Hyrocrop 110 ton ironworker, with tone of tooling and "C" channel blades as well as rod shear angle shear, flat bar shear, coper/notcher and of course punch station, two foot pedals, Boxes of tooling, Electric Stop and cut length gauge, note tooling on wood table same as tooling in green box ...more

Complete with Hoist, 10" high X 15' reach, CM Hoist is 220 volt single phase, Upright has base and provisions to clamp to a Pole or I beam, Was in good running condition when professionally uninstalled, 2000 ABELL-HOWE 1/2 Ton, CM Lodestar Hoist, Electric, 220 Volt 1 Phase, Capacity. 12 T, Length of Span. 15' ...more

Marvel/Spartan PS2828/10 Plate Saw, Blade Size- 2 x.063 x 22 3.75, Speed- 50-250 fpm (15-75 m/min.), Feed Rate:.080-20/m (2-500 mm/min.), Motors:, Blade Drive 7.5 H.P. (5.5 KW), Hydraulic Pump 2 H.P. (1.5 KW), Coolant Pump 1 H.P. (0.7 KW), Shipping sizes, Main, 20'x 66" x 11'6" high, Table 16' x 66" x ...more

Precision Tool room lathe with built in DRO and electronic threading in inch and metric, S:, Series: ATL618E, Swing Over Bed: 11", Swing Over Cross Slide: 6", Spindle Speed: 150 ~ 4,000 rpm, Spindle Nose: 5C (10 degree)/4-degree Taper, Hole Thru Spindle: 1-1/4, Main Motor: 3 HP, Voltage: 230V AC/1PH/3PH, Dimensions: ...more

Supertec STP-618CII 3 axis Surface Grinder, Automatic Surface grinder, Water grinder, 6 x 18, 3 axis grinder with incremental downfeed, fully automatic surface grinder, like Chevalier, Harig, Okamoto, Mitsui, Table Working Surface: 6" X 18", Cross Slide Travel: 7" manual 6 3/4" Automatic, Table Travel: 20.9" Manual ...more

Mattison Model 24-36, Mattison Rotary surface grinder, 18" Wheel, 50HP, 36" Chuck, like Blanchard, Chuck Diameter 36", Max Swing inside guards 48", Max. vertical height of work 12" under new wheels, Grinding wheel size 18", Type of grinder wheel Segmented, Grinding wheel speed 705, Table ( Chuck Speeds) No./ range (4) ...more

Acra 1300 BV Precision Engine Lathe, AC variable speed, 40-2,000 RPM, New Precision Engine lathe Acra ATEL 1300BV With inch/Metric threading, Variable Speed, D1-4 Spindle nose, 1.9/16" Spindle Bore, 40 - 2,000 RPM, Swing over bed 13", Swing in gap 18 - 1/2", Swing over cross slide 8 - 5/16", Spindle Bore 1 - 9/16" ...more

Excellent condition Hole popper EDM, with "Z" axis control and Tooling, 2020 YOUGAR YGS 43Z, Optional 6mm capacity., Hole-Dia. (Min). 0.1 mm, Hole-Dia. (Max). 6 mm, Work-W. 650 mm, Work-L. 910 mm, X. 400 mm, Y. 300 mm, Z. 400 mm.

AD 261DF Formerly XFO10S is replaced by AD 261DF, One Case of Four one Gallon jugs Defoamer helps to break down the foam or bubbles that occur in a machine with High pressure coolant or other foaming characteristics, from ETNA Products Inc., ETNA Products has developed a new and improved defoamer to replace the ...more

HEM vertical infeed, Programmable, 60 degree mitering left or right, Fully automatic, vertical bandsaw, 2007 HEM VT120HA-60, Poer Blade guide, 2 Power vises, Power and programmable tilt, SMart Control, canted head, Swing away control, Work light and manuals, Throat. 18", Work Height. 22", Power. 7.5 hp, Blade Width. ...more

2005 Haas MDC-500, a used vertical machining center from reputable manufacturer HAAS. It boasts an X, Y and Z axis range of 20", 14" and 20" respectively along with 20 hp power. With an impressive RPM of 7,500, an automatic tool changer capacity of 24, and a CAT-40 taper, it's an asset to any operation. Its table ...more