DPA Machinery & Appraisals Llc
Ormond Beach, FL 32174-1435
Surplus Record Dealer Since 2025
Contact
Daniel Abraham
22 listings in 9 categories
2 Roll Plastic Rubber Mills
7 Results
3" x 7" Farrel, high temperature lab mill
Category: 2 Roll Plastic Rubber Mills
Seller: DPA Machinery & Appraisals Llc
Location: Akron, OH
Mfr: Farrel
Farrel 3" x 3" x 7" 2-roll high temperature lab mill. 700 degree capability. Each roll is chrome plated. Each roll is electrically heated via cal rods with their own temperature controller. Each roll has electric air blowers to cool rolls and maintain set temperatures. Each roll is individually driven via 1-1/2 HP ...more
6" x 13" TMP, roller bearing lab mill, chromed rolls, 7-1/2 HP, belly bar safeties, cabinet mounted
Category: 2 Roll Plastic Rubber Mills
Seller: DPA Machinery & Appraisals Llc
Location: Akron, OH
Mfr: Tmp
Like new TMP "Technical Machine Products" 2-roll 6" x 6" x 13" lab mill with chromed rolls. "ROLLER BEARINGS". 7 1/2 hp 460VAC inverter duty gearhead motor, Triple chain drive. Front and rear belly bar safeties. Positive pullback assemblies. Flip up batch guides. Ready to go.
22" x 22" x 60" Farrel, rubber mill, left hand drive, Falk 80.55:1 reducer w/ air brake, 150 HP @ 1800 RPM, 440 VAC motor
Category: 2 Roll Plastic Rubber Mills
Seller: DPA Machinery & Appraisals Llc
Location: Akron, OH
Mfr: Farrel
1-Farrel 22"x22"x60" 2 roll rubber mill. Direct connected and unitized on a 2-piece left hand drive keyed base. Falk 2150Y3A, 80.55 to 1 gear reducer with Fawick air brake. US motors 440VAC 1800 rpm motor. Positive pullbacks with shear pins on front adjustable roll. Cored rolls and water cooled bearing housings. ...more
22" x 22" x 66" Nippon, 2-roll mill, roller bearing, variable speed, variable friction, rubber or silicone
Category: 2 Roll Plastic Rubber Mills
Seller: DPA Machinery & Appraisals Llc
Location: Ormond Beach, FL
Mfr: Nippon
1-Nippon 22" x 22" x 66" two roll rubber or silicone mill. Direct connected and unitized on a two piece base. Each roll driven via parallel shaft Hansen reducers with separate 60HP variable speed DC motors and SCR's. 120HP total horsepower. This setup has variable speed and friction up to 24 RPM on either the front or ...more
26" x 26" x 84" Adamson United, rubber or plastic mill, 2-roll, 500 HP, drilled rolls, motorized roll adjusters, dual 250 HP drives
Category: 2 Roll Plastic Rubber Mills
Seller: DPA Machinery & Appraisals Llc
Location: Akron, OH
Mfr: Adamson
1-Adamson 26" x 26" x 84" 500HP 2 - roll plastic/rubber mixing mill. Motorized roll adjusters can be replaced with hydraulic cylinders. Direct connected and unitized on a three piece heavy "I" beam steel base with leveling pads. New in 1988. Both rolls are triple pass "drilled" for heating or cooling and have 17" ...more
26" x 26" x 84" Stewart Bolling, 2-roll twin rubber mixing mill, 2-drilled front rolls
Category: 2 Roll Plastic Rubber Mills
Seller: DPA Machinery & Appraisals Llc
Location: Akron, OH
Mfr: Stewart Bolling
Year: 1988
Stewart Bolling 26" x 26" x 84" twin rubber mill. Recently removed from a rubber manufacturing facility that closed in July of 2023. This mill was rebuilt by Stewart Bolling in 2016. Both front rolls are triple pass "drilled" rolls. Rear rolls are cored. Direct connected and unitized on a 4-piece keyed base with ...more
28" x 100" Bolling, 500 HP hydraulically driven mill, hydraulic roll adjusters, drilled rolls
Category: 2 Roll Plastic Rubber Mills
Seller: DPA Machinery & Appraisals Llc
Location: Akron, OH
Mfr: Bolling
1-Bolling 28" x 28" x 100" 2 roll rubber mill with front and rear "drilled" rolls. 500HP Haaglunds hydraulic variable speed marathon motor direct connected to drive roll. 500HP AC motor inside hydraulic pump cabinet. Hydraulic roll adjusters. 27/29 tooth connecting gears generating a 1.074 friction ratio. All ...more
Extruders
2 Results
3.5" NRM #Plastiscrew, cold feed, 12:1 L/D rubber extruder
Category: Extruders
Seller: DPA Machinery & Appraisals Llc
Location: Akron, OH
Mfr: Nrm
Model: PLASTISCREW
NRM 3 1/2" Plastiscrew cold feed rubber extruder with swing head in good condition. 24.88 to 1 reducer. 75HP DC motor.
10" Farrel, hot feed dump extruder, 6:1 L\D, 17" x 30" feed opening, 150 HP Reliance DC motor
Category: Extruders
Seller: DPA Machinery & Appraisals Llc
Location: Akron, OH
Mfr: Farrel
Year: 1990
Farrel 10" hot feed 6 to 1 L\D dump extruder with a 17" x 30" feed opening. Ideal for a drop extruder from a F80 mixer. Sumitomo 62 to 1 reducer, 150HP Reliance DC motor,0 to 24 rpm screw speed, 2 attached screening swing heads with hydraulic clamp.
Extruders and Extrusion Lines
2 Results
3.5" Mitsuba #90G-12D-HBET-4294, rubber extruder, 12:1 L/D, 60 HP DC, cold feed 3-1/2", motorized puller, Cut-To-Length line cutter, under power, 1995
Category: Extruders and Extrusion Lines
Seller: DPA Machinery & Appraisals Llc
Location: Ormond Beach, FL
Mfr: Mitsuba
Model: 90G-12D-HBET-4294
Year: 1995
1-Mitsuba 3 1/2" 90MM cold feed rubber extruder with puller and automatic/manual cut to length cutter. 12 to 1 L/D ratio. 0 to 43 rpm. Swing head with multiple dies included. Power gear driven roller feed. 3 zone TCU. 60HP/45KW variable speed motor and SCR drive. Complete operators controls with separate controls for ...more
4.9" Mitsuba, rubber extruder, 12:1 L/D, 100 HP variable speed, cold feed, power roller feed, under power, 1998
Category: Extruders and Extrusion Lines
Seller: DPA Machinery & Appraisals Llc
Location: Ormond Beach, FL
Mfr: Mitsuba
Year: 1998
1-Mitsuba 125MM cold feed rubber extruder in excellent operating condition. 12 to 1 L/D ratio. 4.92 diameter screw. Power roller feed, 75KW/100HP variable speed DC motor and SCR drive controller. 4 zone TCU unit. 0 to 37 RPM screw speed. Quick change swivel head with clamp and dies. Comes with a puller/cut to lenghth ...more
Gear Reducers, With Driving Unit
1 Result
250 HP, 2000 RPM, Lufkin #THB440CH, right angle drive, 64.69:1 ratio, 1.68 service factor, coupled to a Reliance DC 500 Volts motor
Category: Gear Reducers, With Driving Unit
Seller: DPA Machinery & Appraisals Llc
Location: Ormond Beach, FL
Mfr: Lufkin
There are two of these identical units available. 1 reducer has a left hand output shaft and the other has a right hand output shaft. Both are mounted on a structural steel base. Both Lufkin reducers have modern fabricated steel housings with motorized oil pumps for the shaft roller bearings so you can run at low ...more
Gearboxes (Gear Reducers - No Driving Unit)
3 Results
300 HP @ 1200 RPM, Falk #2185YN3-B, 71.33:1 ratio
Seller: DPA Machinery & Appraisals Llc
Location: Barberton, OH
Mfr: Falk
Model: 2185YN3-B
1- Falk model 2185YN3-B parallel shaft gear reducer with a 71.33 to 1 ratio. Rated for 300HP @ 1200 input speed output speed is with a 1.5 service factor. Has dual input and output shafts and has a Fawick air brake in excellent condition still installed.
400 HP @ 900 RPM, Lufkin #T540AH, 1.5 service factor, 50.78:1 ratio
Seller: DPA Machinery & Appraisals Llc
Location: Akron, OH
Mfr: Lufkin
Model: T540AH
Lufkin T540AH with double input and single output shafts. Parallel shaft, set up for left hand drive. Will rate for 400hp @ 900 rpm input speed. Excellent condition. Gears were replaced and ratio changed in 2016. Reducer was a spare for a 84" rubber mill. It has 1/2 of a 26 tooth chain coupling still installed and the ...more
500 HP @ 1200 RPM, Lufkin #T720BHH, 62:1 gear reducer
Seller: DPA Machinery & Appraisals Llc
Location: Akron, OH
Mfr: Lufkin
Model: T720BHH
1-Lufkin T720BHH 62 to 1 gear reducer rated for 500HP @ 1200 rpm input speed. Fawick 20CB air brake installed. Dual input and output shafts. Excellent condition., DPA stocks several other Lufkin T720's, T540's, and T390's for mills and calenders.
Farrel #BR82, roller bearing, 2.7 lbs. per batch, lab Banbury
Category: Lab Mixers
Seller: DPA Machinery & Appraisals Llc
Location: Akron, OH
Mfr: Farrel
Model: BR82
Year: 1987
1-Farrel "BR82" laboratory banbury mixer. 2-wing rotors. 2.7 lbs per batch. Recently removed from a GE plastics laboratory. This is a unique lab mixer as it has factory Farrel "FYH" hydraulic dust stops with it's own power unit. Roller bearings on rotors. Pneumatic swing open side discharge on operators side of mixer ...more
Farrel #OOC, roller bearing lab, 7 lb. per batch lab Banbury
Category: Lab Mixers
Seller: DPA Machinery & Appraisals Llc
Location: Akron, OH
Mfr: Farrel
Model: OOC
Farrel ''OOC'' cabinet design lab mixer. 2 wing rotors with roller bearings. 7 lb. capacity at 1.0 specific gravity. 15/30 HP 2 speed motor with starters and controls. Pneumatic side opening discharge with controls. Special HY-Comp non lubricated dust stops are available for this size mixer.
Miscellaneous Plastic and Rubber Equipment
2 Results
Midlands Millroom Supply Midlands, 20" cantilever batch-off, batch manipulator, strip cooler batch-off machine
Seller: DPA Machinery & Appraisals Llc
Location: Laurens, SC
Mfr: Midlands Millroom Supply
1-Midlands millroom supply 20" cantilever batch-off with batch manipulator and strip cooler batch-off machine. New in 2004. Still installed and can be seen fully operational to a serious buyer. Complete set of drawings and instruction manuals included. 480VAC with 110V control curcuitry.
RCM #NBC32, 32" rubber bale cutter
Seller: DPA Machinery & Appraisals Llc
Location: Laurens, SC
Mfr: Rcm
Model: NBC32
Year: 2004
Like new 32" RCM hydraulic bale cutter on stand with entrance and exit guards and roller conveyors. Complete operators control station with dual cloase buttons and self contained hydrauilc unit installed on cutter. Light curtains on front and rear of bale cutter., Can be seen operating or can make a video of cutter ...more
Mixers-blenders and Agitators for Rubber or Plastic
1 Result
Farrel #F80, 4 wing " ST" rotors 600 HP unidrive, 600 HP DC motor, 1997
Seller: DPA Machinery & Appraisals Llc
Location: Ormond Beach, FL
Mfr: Farrel
Year: 1997
1-Farrel F80 4-wing banbury with "ST" rotors. 16" hopper. Lufkin 16.43 to 1 uni-drive reducer. GE 600HP DC motor 500V with a 300V field. Hydraulic unit for drop door. Banbury is in excellent condition and there is a recent inspection report available. There are no controls or scr drives included with this mixer. New ...more
Plastic and Rubber Calenders
2 Results
16" x 48" 2-Roll Vertical Roller Bearing Calender, motorized 6 cooling drum train
Category: Plastic and Rubber Calenders
Seller: DPA Machinery & Appraisals Llc
Location: Akron, OH
Model: 16X48CAL
Year: 2015
Almost new 16" x 16" x 48" 2 - roll vertical calender for rubber, plastic, or silicone. Solid steel end frames and steel bearing housings 50hp variable speed AC Frequency motor with 480 volt AC variable speed drive. 0-25 RPM. Roller bearings on all 4 journals. Even speed herringbone connecting gears. Motorized top ...more
24" x 68" Adamson, 3 roll calender w/ a top inclined roll
Category: Plastic and Rubber Calenders
Seller: DPA Machinery & Appraisals Llc
Location: Akron, OH
Mfr: Adamson
Adamson 24" x 68" 3-roll calender with a top offset roll for easy feeding. Roller bearing. Right hand drive. Top and center rolls are "NEW" and are triple pass drilled for best heating or cooling capability. New Timken roller bearings on top and middle roll. New full circle bronze bearings on bottom roll. Handwheel ...more
