Bass Machinery LLC

225 KVA MGM Transformer, Voltage: 480, Hertz: 60, Phase: 3.

12.7mm NIKOM High Speed Impact Shear, 2-Plane Straightener, 100 PPM @ 2 Length, AGE: 1995, MODEL NUMBER: PSA20, Machine designed to shear at a high rate of speed, greatly, reducing plastic deformation, resulting in clean, burr-, free, square and scrap-free cuts. Machine is currently set-, up to be fed from coil or ...more

SOUTHWESTERN INDUSTRIES Trak K3-E Vertical Mill, Quill Diameter: 3.375", Table: 50" x 10", Table Capacity: 750 Lbs., Table Travel: 32", Knee Travel: 16", Ram Travel: 24", Quill Travel, Max.: 5", Spindle Taper: R8, Spindle Speed: 30 to 4200 RPM, Head Tilt, Front-Back: 45 Degrees, Head Tile, Left-Right: 90 Degrees ...more

CEMCO Model URBB-3337-MW Wet Finishing Machine, AGE: 1993, Factory Refurbished In 2008, Working Width: 36", Part Length, Min.: 12", Part Height, Max.: 6" (Est.), CONSISTS OF (3) FINISHING STATIONS:, Station 1: 36" Wide Belt Grinder, Station 2: (12) 6" Dia. Vertical Brushes With 1" Long, Grit ...more

Media Reclaim System, *** This is avialble for sale as a system or, *** as individual components, CONSISTING OF:, Sand Reclaim Pot, Overhead Cyclone, Vibratory Sifter, SYSTEM CONSISTING OF:, METAL IMPROVEMENT "Peenamatic" #613 Automatic Grit Blaster:, (8) Nozzles Mounted to a Pneumatically Operated Overhead Asembly ...more

(2) 2 Ton DEMAG Model DC-ProFC10 2000 2/1 H5 V6 Electric Chain Hoist System, AGE: 2016, MODEL NUMBER: DC-ProFC10 2000 2/1 H5 V6, Chain Hoist Lift: 16', Setup for 480/60/3 Cycle and 110 Volt Control, Lift is a Magnetek Impulse VG+ Series 4, 2-Step, Infinetly Variable, Adjustable Frequency / Vector, Crane Controls @ 0 ...more

TECHNOTRANS Model RL 7/0 SK V2 Chiller, AGE: 2023, Originally Used to Chill a Trumpf Laser, Capacity: 3.21 Ton (11.3 kW) @ 68 Deg. F @ Ambient Temperature of 90 Deg. F, Refrigerant: R513A, Digital Temperature Control, Water (Water/Glycol) Recirculating Pump:, 24.8 GPM, 95.3 PSI (Nominal), 14.6 PSI (Max.), Top Mounted ...more

12" W x 8" H CLEAN MACHINE 3-Stage Parts Washer, All Stainless Steel Construction, Belt Width: 12", Opening Height: 6-1/2", Modifiable to 10", Floor to Top of Belt: 43", 16" Load Length, 36" Long Wash Section:, (5) Top Spray Bars with 3/2/3/2/2 Nozzles, (3) Bottom Spray Bars with 3 Nozzles Each, (3) 12 kW Indeeco ...more

OBERLIN Model OPF-2 Paper Filtration System, Media Width: 20", Automatic Pressurized Coolant Filtration System, using Filter Pump Pressure to Force Liquid through, the Filter Media Building a Cake of Filtered Out Material, Thus Increasing the Filters Ability to Catch Smaller and, Smaller Fines which Greatly Improves ...more

30 Ton BUSHMAN Spreader Beam, Capacity: 30 Ton, Overall Length: 245", Available Hook Width Pin Positions: 52", 6', 8', 10', 12', 14', 16' & 19', Beam can be Picked with Sling, Holes in Welded Brackets on, Each End: 232" Apart, 3/4" Dia. Center Lift Pin is Removable, Crosby/Bullard ...more

12 Ton TISHKEN Model 21562150 Tilt Frame Cut-Off Press, MODEL NUMBER: 21562150, Stroke: 2", Shut Height: 6.5", Ram Adjustment:.5", Bed Size: 8" x 12", Adjustable Height Base, Air Clutch & Brake, OVERALL DIMENSIONS: 42" x 32" x 80" High, WEIGHT: 2,500 Lbs.

SUGINO "Jet Flex" Jet Clean Center, AGE: 2010, Can also be used to Dry as the Last Function, All Wet Areas are Stainless Steel Construction, Work Envelope: 1650mm X, 500mm in Both Y and Z, Turntable for Loading and Unloading while Second Table of, Fixtured Parts are Being Deburred and/or Cleaned, Each Table has a 4th ...more

SPX-DELTECH Model RP300 Externally Heated Desiccant Air Dryer, AGE: 2014, SCFM: 300, PSIG: 100, Operating Temperature, Max.: 120 Degrees, Desiccant Type: Activated Alumin, Controls, 120/1, MOTOR DATA: 5kW Heater, 460/3.

60 Ton ROUSSELLE Model 6B60 Double Crank Gap Frame Press, Capacity: 60 Ton, Stroke: 4", Shut Height: 13-1/2", Adjustment: 3", Bed: 18" x 60", Ram: 16" x 48", Bolster: 1-7/8" Thick, 1/2" Tee-Slotted and Drilled/Tapped, Ram Plate, Full Size: 1-3/8" Thick, (6) L-R T-Slots, Strokes Per Minute: 50, Air Clutch and Brake ...more

15-3/8" / 22-7/8" x 85" cc NARDINI Model ND1585E Engine Lathe, Swing Over Bed: 15-3/8", Swing Over Cross Slide: 8-5/8", Swing in Gap: 22-7/8", Distance Between Centers: 85", Cross Slide Travel: 9-7/8", Hole Through Spindle: 2-1/32", Spindle Nose: D1-6, Spindle Taper: MT#4, Spindle Speeds: (18) 25 to 2000 RPM, Feed ...more

5" x 5" x 1/2" PEDDINGHAUS Peddimaster Model 88/120 H Hydraulic Ironworker, (4) Work Stations, Shear Cut Round or Flats, Tonnage: 88, Shear Capacity: 20" x 5/8", Length of Shear Blades: 20", Angle Shear @ 90 Degrees: 5" x 5" x 1/2", Angle Shear @ 45 Degrees: 3-1/2" x 3-1/2" x 3/8", Punch Capacity: 1-1/16" x 3/4" ...more

LABEL-AIRE Model ASDU Labeling Machine, (2) Available, AGE: 2017, MODEL NUMBER: ASDU LH 2" FSTN LPBOX and ASDU RH 2" FSTN LPBOX, Used to Feed a Label Applicator and Burn Lot #'s Onto Each Label, Takes a 2-Color Label and Burns Off the Top Color, Label Width, Max.: 2", UNWD: 20", Up to 5000 IPM, 30 Watt DOMINO Laser ...more

COLUMBIA MARKING TOOLS Model 860 Roll Stamp Marking Machine, AGE: 2009, MODEL NUMBER: 860, Air Actuated, Floor Style, Mounted To Heavy Duty Machine Base, Length of Vertical Stroke: 3", Length of Roll Stroke: Adjustable To 3 1/2" Max., Direct 1000 View with Touch Pad for Machine Operation, Programming ...more

SEPARATION DYNAMICS Extran Ultrafiltration Water Filtration Unit, Removes suspended and emulsified oils and process, contaminates in wash water., In-Line Bag Filter for Process Contaminates, Maintenance-Free Extra Cellulose Hollow Fiber Filter, Replaced 6/23, Membrane to Remove Oils While Passing Clean, Water and Wash ...more

1-1/2" x #6 x 72" STANDARD RAISED EXPANDED METAL Flattener, 4 Over 3, Flattening Rolls: 8" Dia. on 9" Centers, All (7) Rolls are Individually Driven, By Separate Motors, Pair of Driven Urethane Entry Pinch Rolls:, 6" Diameter with Upper Roll Pressure by, (2) Pneumatic Cylinders, Roll Length: 75", (1) Smaller Exit ...more

120 Ton FARGER & JOOSTEN MULTIPOWER Air/Oil Press, Built for Side-to-Side Feed, Tonnage, Est.: 120 Ton, Stroke: 7.9", the last.79" is the Power Stroke, Daylight Opening: 26", Bed: 24" LR x 17" FB x 2" Thick, Ram: 24" LR x 17" FB x 2-1/2" Thick, Force in Approach Stroke: 23.1kN, Force in Retract Stroke: 22.3kN ...more

33,000 Lb. MITCHELL Hydra-Push 2-Die Hydraulic Push Pointer, Capacity: Rated - 33,000 Lbs. @ 1989 PSI, Maximum - 41,480 Lbs. @ 2500 PSI, Die Holder: 2-Hole Swing Type Rotary, Die Pocket: Accepts 4" and 3" (with Adaptor), Die Casing Diameters, Automatic Cycle:, (1) or (2) Die Reduction, in Point Mode or Nibble Mode: ...more

CLAIR Pass Through Polishing Machine, Capacity, Width: 24" Wide Belt, Current Horizontal Brush: Scotch Brite, 25" Long x 10" Diameter, Appears to be Near New, Manual Hand Wheel for Belt Feed Table Gap Adjustment, Percent Motor Load Current Meter, Variable Speed Feed Belt Control, Pneumatic Filter, Lubricator and ...more

SCHUTTE BUFFALO Model 18-7-300 Hammer Mill, AGE: 2011, Hammer No.: 1147, Capacity: 18" Dia. x 7" Wide, RPM: 3600, 300 Degree Screen, Gravity Discharge, Load Hopper, (1) 1/8" Dia. Screen, (1) 3/32" Dia. Screen, (2) Product Collection Barrels, Duct Work, MOTOR DATA: 20 HP Hammer, 230/460/60/3, 10 HP ...more

12-Stand DAHLSTROM Model 400-12 Roll Former, AGE: 2005, 12-Stand on a 16-Stand Base, Spindle Diameter: 2", Roll Space: 8", Horizontal: 13", Vertical: 4-1/2" to 7-1/2", Keyway: 3/8", Base to Centerline: 7-3/8", Speed: 60 to 100 FPM, Roll Diameter: 8", Line Direction: Right-to-Left ...more

12" x.156" LITTELL Model 412-7 PDL Straightener, 3 Over 4, All Rolls Driven, Capacity:.156" Thick x 12" Wide, Straightener Rolls: 3" Dia. x 12-1/2" Long, Pinch Roll Diameter: 4.25", Center-to-Center: 5-1/2", Speed, Max., Approx.: 37 FPM, Feeding Line Height: 48", Direction: Right to ...more

40 Ton ROUSSELLE Model 4 OBI Press, TEMPORARY :, Capacity: 40 Ton, Stroke: 3", Shut Height: 12", Adjustment: 3-1/2", Bed Size: 16" x 26", Throat: 18", Bolster: 2-1/2" Thick Approx., (7) L-R Tee-Slots, Floor to Top of Bolster: 36", Die Shank: 2" Diameter, Strokes Per Minute: 105, Touch Type Dual Palm Buttons ...more

Our stock number: 51762, 60 Ton JOHNSON OBI Press, 4 Str, 15 SH, 56 x 22 Bed, 100 SPM, 5 HP, Updated, MODEL NUMBER: G2-60-56-22, YEAR: 1965, Stroke: 4", Shut Height: 15", Ram Adjustment: 3-1/2" - Manual, Bed Area: 56" x 22", Bolster 56" x 22" x 2 3/4" T-Slotted, Ram Area: 40" x 22", Strokes Per Minute: 100, Operator ...more

100 Ton ROUSSELLE Model S2-30-100 SSDC Press, Stroke: 4", Shut Height: 15.25", Ram Adjustment: 4", Bed Size: 100" x 30", Ram Size: 97.5" x 20.7", Speed: 50 SPM, Window: 14" x 15", Between Housings: 80", Air Clutch & Brake, Air Counterbalance, GE Fanuc Quick Panel Controller ...more

*** This is available for sale as a complete system or, *** as individual components, METAL IMPROVEMENT "Peenamatic" Model 613 Automatic Grit Blast System, AGE: 1995, MODEL NUMBER: 613, (8) Nozzles Mounted to a Pneumatically Operated, Overhead Assembly that Lowers and Lifts the Nozzles, to Allow for Ease of Loading ...more

15 HP QUINCY Model QT-15 Air Compressor, AGE: 2003, MODEL NUMBER: QT-15, Horizontal, Tank Mounted, 120 Gallon, PSI: 200, MOTOR DATA: 15 HP.

250" x 54" SESCO Model 12-XXX 5-Roll Straightener, Capacity:.250" @ 54",.375" @ 18", Material Thickness:.030", No. of Straightener Rolls: 2 Over 3, Straightener Roll Diameter: 6", Entry & Exit Pinch Rolls: 8" Dia. w/Adjustable Pneumatic, Cylinder Pressure, Line Speed, Max.: 150 FPM, Straightener Roll Depth ...more

3" PINES Model 2 Horizontal Hydraulic Tube Bender, Capacity:, Extra Heavy Pipe IPS: 2" Schedule 80, Non-Ferrous Tube, YP: to 12,000 PSI 3-1/2" x.188", Non-Ferrous Tube, YP: to 25,000 PSI 3-1/2" x.120", Steel Tube, YP: to 40,000 PSI 3-1/2" x.083", Steel Bar Round, YP: to 40,000 PSI 1-7/8" Dia., Counter-Clockwise ...more

27" Dia. x 36" H BETTER ENGINEERING "Genesis" Model G200 Parts Washer, AGE: 2016, Capacity: 27" Dia. x 36" High, Mild Steel, Wash Only, Electrically Heated, 100 GPM Rosedale Filter (7.2" x 16"), Motorized Steam Exhaust, Ball Valve Skimmer (Weir Plate), 7-Day Timer, NOTE: Originally Built 460V, MOTOR DATA: 1/4 HP ...more

2,500 Lb. DALLAS Model 06090 Motorized Uncoiler, Variable Speed, Coil Weight: 2,500 Lbs., Coil I.D.: 16" to 20", Coil Width: 12" with Keepers, Loop Control Arm, Adapted with Roller Frame, (3) Inner and (3) Outer Keeper Arms, Manual Expansion.

9.8" x 23.6" KELLENBERGER Model 600-U-125 Universal ID/OD/End Face Cylindrical Grinder, AGE: 1986, TEMPORARY :, Swiss, High Production, Universal I.D./O.D. Cylindrical Grinder, Swing, Max., As Presently Set Up: 9.8", Swing, Max., with Factory Risers: 19.8", Distance Between Centers, Nominal: 23-5/8", Distance Between ...more

FADAL Model 904-1 Vertical CNC Mill, Table: 40" x 20", CAT-40 Spindle Taper, Fadal CNC-88 Control, 21-Position Tool Changer, New, Unused Keyboard, MOTOR DATA: 220/60/3, CONDITION: As Taken Directly from Service.

PROCECO Model MBCW 24X16-4W-2R-BO-SS Dunnage Washer, All Stainless Steel Tanks and Enclosures, Opening, Width: 10"+ (Adjustable Guide Rails Installed On Site), Width of Current Rail Settings: 6-5/8", Opening, Height: 52", Built for Standard 48" x 48" Dunnage, Tunnel: 5' Long with 26" Wide Spray Zone, Wash and Rinse ...more

18" TIMESAVERS Model 6019-1 Wood Polishing Belt Grinder, AGE: 1990, Grinding Belt Width: 18", Feed Belt Width: 19", Hour Meter: 520 Hours, Adjustable Belt Polishing Pad, Dual Belt Lower Pressure Rolls, Motor Amp Meter, Manual Bed Height Adjustment, Variable Feed Belt Speed, Electrical Drawing, Automatic Grinding Belt ...more

32" Roll Coater, Roll Length: 32", Roll Diameter, Urethane Top Roll Applicator: 9", Roll Diameter, Lower Pressure Roll: 8", Passline: 39", (2) 4-1/2" Diameter Doctor Rolls which can be Rocked into, Both Gear Drive and Contact with Applicator Roll via, Manual Handle, Variable Speed Drive Control, Liquid Pump, Upper ...more