Advanced Search
Surplus Record logo

SLITTING LINES

66" x 6.5" Stamco, 40000 lb., 2-heads, 125 HP DC, #6497

Request a Quote
More Photos & Detailed Specs
Share


General Specifications


Width: 66.0"
Arbor: 6.500"
Manufacturer: Stamco
Lbs.: 40000
Stock #: 6497
Price: Request a Price

Dealer Information
D & H Machinery Inc logo
D & H Machinery Inc
723 Phillips Ave. Bldg D2
Toledo, OH 43612

Contact: Sales
Tel: 419-841-3586
Fax: 419-841-2986
Email: sales@dnhmachinery.com
  
Gold Level Dealer Since 1963
Website: www.dnhmachinery.com

View our Equipment Listings

Detailed Product Description


This is a high speed coil slitting line.
It was originally built in 1985/6 by Monarch Stamco.
The following product mix was run on this line:

1) 5-out Can Stock
2) 10-out Can Stock
3) 12-out Can Stock
4) Brazing Stock
5) Lid Stock

Gauge and Coil Limitations:

Gauge Max: 0.075"
Gauge Min: 0.005"

Entry Coil Width: 30" - 66"
Exit Coil Width: 0.75" - 66" Slit
Entry Coil O.D.: 40" - 96"
Exit Coil O.D.: 20" - 96"
Coil Weight Max: 40,000 lbs
Approx. Cuts: 30 of 0.020"
16 of 0.030"
8 of 0.075"
Operational Modes: Tight line and single loop
Hand of Line: Right hand
Line Speed: 0 to 2000 fpm @ 20" Bare Drum Speed
50 fpm - jog/thread

Equipment Specifications

-Turnstile: Stamco
Type: 4-arms w/Power Rotation
C-Hook Type Arms will accept 16" I.D. Coils
45" Usable Arm Length
Hyd. Motor: 1 hp
8 cu.in/rev @ 113 rpm = 4 gpm
      Pump: 8 gpm @ 1000 psi
      Turnstile Detente Cylinder: 3.25" bore, 2.5" stroke
Passline Height: 46.5" from Floor to Top of Arm
Overall Length: 197.5"
Base Size: 60" Dia.
      
-Coil Car: Southworth
      Scissor lift type
72" Long "V" Cradle
Approx. 32" from Floor to bottom of "V" Cradle
      Core remove and dump feature
      System Pressure: 1800 psi
      Rise Time: 56 seconds
      Tilt Time: 2-3 seconds
      Traverse Speed: 40 fpm
Hydraulic Power Supplied by Uncoiler
Overall Size: 72" L x 78" W x 38" High

-Mandrel Type Uncoiler: Stamco
Sales Order: 404-84-9B
Machine # 4453
69.5" Mandrel Face Width
Hydraulic Expansion
Expansion Range: 16" to 20"
      Cylinder: 8" bore, 12" stroke
      Drive Motor: 125 hp DC, 300/1800 rpm, 240 V
DC Holding Brake
      Reducer w/2.972:1 Ratio
      Blower Motor: 1.5 hp, 1730 rpm
      Lube Pump Motor: 1.5 hp, 1800 rpm
      Attached Holddown Roll
       Hydro-Motor: 23.8 cu.in/rev @ 45 rpm = 6 gpm
       Lift Cylinder: 4" bore, 17" stroke
       Roll: 8" dia., 18" face, polyurethane cover, 80-90 durometer
Passline: 54" from Floor to Center of Mandrel

- Edge Guide Unit: MEA
      Type: 24" positioner with LE105 edge guide laser sensor
      Pump Drive: 20 hp, 1150 rpm
      Hyd. Tank Capacity: 150 gallons
      Pump: 20 gpm @ 1200 psi

- Coil Peeler Table

- Pinch Roll And Drive: Stamco
      Drive Motor: 20 hp, 850/2300 rpm
      Lift Cylinders (2 ea): 3.25" bore, 7" stroke
      Rolls: 1 ea, 8" dia., 72" Face, polyurethane cover, 85-95 duro.
1 ea, 16" dia., 72" face, polyurethane cover, 85-95 duro.

- Thread Table & Deflector Pinch Roll: Stamco
      Upper Cylinders (2 ea): 3.25" bore, 7" stroke
      Lower Cylinder (2 ea): 3.25" bore, 6" stroke
      Swing Roll (2 ea): 3.25" bore, 5" stroke
      Hydro-Motor: 23.8 cu.in/rev. @ 48 rpm = 6.5 gpm
      Rolls (2 ea): 8" dia., 72" face, polyurethane cover,
85-95 durometer.

- Straightener: Stamco
      Motor: Hydro-Motor,
      11.9 cu.in/rev. @ 12 gpm
      Lift Cylinders (2 ea): 3.25" bore, 4" stroke
      Work Roll: 2.5" dia., 84.5" face
      Back-up Roll: 4" dia., 72" face, 2" pitch grooved,
right-hand spiral
      Bridle Rolls (2 ea): 8" dia., 72" face, poly. cover, 85-90 duro.

- Slitter Heads: Stamco
Two Removable Heads
Sales Order 476-86-10A
      Arbors: 6.5" Dia. x 72" Face Arbors
      Drive Motor: 75 hp DC, 300/1800 rpm, 240 V
      Pinion Stand Gear Ratio: 1.5:1
      Blower Motor: 1.5 hp, 1730 rpm
      
- Scrap Baller: Stamco
      Drive Motor: 50 hp, 850/2550 rpm
      Gear Ratio: 4.067:1
      Eject Hydraulic Cylinder: 4" bore, 15" stroke
      Traverse Hydraulic Cylinder: 4" bore, 46" stroke
      Air Cylinder: 8" bore, 21" stroke
      Air Cylinder: 6" bore, 7" stroke

- Synchro-Wind Tension Stand: Stamco
Machine No.: 4460
Sales No.: 418 84 24A
Entry Separator Tooling Bar
Entry Passline Roll
Tension Rolls (2 ea): 16" dia. x 66" face
serrated polyurethane covered
      Drive Motor: 150 hp DC, 300/1500 rpm
      Gear Ratio: 1:1
      Blower Motor: 1 hp, 1725 rpm
      Lift Hydraulic Cylinder (2 ea): 3.25" bore, 25" stroke
      Air Cylinder: 2.5" bore, 2" stroke
      
- Exit Crop Shear: Stamco
S/N: 1363
Mechanical Operation
Capacity: 0.125" Mild Steel
74" Long Blade
38" Passline Height
3 HP GE AC Motor, 1145 RPM, 220/440 V
Overall Size: 125" L x 46" W x 61" High

- Exit Threading Table

- Recoiler: Stamco
Mandrels (3 ea): 12"/16"/20" Diameters x 84" Face Width
      Drive Motor: 125 hp DC, 300/1800 rpm
      Gear Ratio: 4.12:1
      Blower Motor: 1.5 hp, 1800 rpm
      Lube Pump Motor: 1.5 hp, 1800 rpm
      Mandrel Cylinder: 10" bore, 6" stroke
      Pusher Plate Cylinder: 4" bore, 107" stroke
Passline: 44" from Floor to Center of Drum
Powered Outboard Support
      
- Entry Hydraulic Unit
      Tank Capacity: 105 gallons
      Motor: 15 hp, 1200 rpm
      Pump: 26 gpm @ 1200 rpm
      System Pressure: 850 psi

- Exit Hydraulic Unit
      Tank Capacity: 150 gallons
      Motor: 25 hp, 1200 rpm
      Pump: 47 gpm @ 1200 rpm
      System Pressure: 900 psi

-Line is in Storage: Toledo, Ohio